• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.8
• /
• pp.905-910
• /
• 2014

The steel grating discussed in this study is a drain cover that enhances the rigidity of the steel frame using an inclined inflow tract for wastewater, facilitates smooth drainage, and prevents the escape of bad smell from the drain. Recently, the urban problem of bad smell in sewerage lines has been hindering the improvement of living standards. Moreover, the frequent failure of existing products deters bad smell prevention measures and results in administrative power and budget wastage. The pressure to reduce budgets propels the increased demand for functional steel grating. Thus, this study focused on optimizing the design parameters of a steel grating by simultaneously considering its rigidity and drainage efficiency.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.507-512
• /
• 2000

This paper presents a design procedure using the moment magnifier method that is applicable to RC flat plates subjected to combined axial compressive and uniform or non-uniform floor load. Based on the numerical results, the design values of the buckling coefficient and the effective flexural rigidity, that define the buckling force, have been proposed. Using these design values, this paper provides the design procedure for the moment magnifier method.

• Korean Journal of Computational Design and Engineering
• /
• v.12 no.5
• /
• pp.376-381
• /
• 2007

The geometric configuration in the weight-reduced structure is very required to be started from the conceptual design with low cost, high performance and quality. In this point, a structural-topological shape concerned with conceptual design of structure is important. The method used in this paper combines three optimization techniques, where the shape and physical dimensions of the structure and material distribution are hierachically optimized, with the maximum rigidity of structure and lightweight.

• Wind and Structures
• /
• v.11 no.2
• /
• pp.153-178
• /
• 2008

Based on the empirical formulas for power spectra of generalized modal forces and local fluctuating wind forces in across-wind and torsional directions, the wind-induced lateral-torsional coupled response analysis of a representative rectangular tall building was conducted by setting various parameters such as eccentricities in centers of mass and/or rigidity and considering different torsional to lateral stiffness ratios. The eccentricity effects on the lateral-torsional coupled responses of the tall building were studied comprehensively by structural dynamic analysis. Extensive computational results indicated that the torsional responses at the geometric center of the building may be significantly affected by the eccentricities in the centers of mass and/or rigidity. Covariance responses were found to be in the same order of magnitude as the along-wind or across-wind responses in many eccentricity cases, suggesting that the lateral-torsional coupled effects on the overall wind-induced responses can not be neglected for such situations. The calculated results also demonstrated that the torsional motion contributed significantly to the total responses of rectangular tall buildings with mass and/or rigidity eccentricities. It was shown through this study that the framework presented in this paper provides a useful tool to evaluate the wind-induced lateral-torsional coupled responses of rectangular buildings, which will enable structural engineers in the preliminary design stages to assess the serviceability of tall buildings, potential structural vibration problems and the need for a detailed wind tunnel test.

• Journal of Distribution Science
• /
• v.18 no.11
• /
• pp.5-13
• /
• 2020

Purpose: This research investigates the cost behavior of the distribution industry. Specifically, we investigate if the ratio of the increase in costs with an increase in sales is consistent with the ratio of the decrease in costs when sales decrease. Traditionally, cost is assumed to be symmetrical. In the case of the distribution industry, it was expected that the downward rigidity of the cost would be shown because it would be very difficult to decide to adjust resources when sales temporarily decrease. Therefore, studies have looked at Korean capital markets based on manufacturing and steel industries. However, no research has been done on the distribution industry. Research design, data, and methodology: To verify the hypothesis of this study, the asymmetry of cost was measured by Anderson et al. (2003). The sample used 28,695 firm-year data from 2002 to 2019 for the KOSPI and KOSDAQ stock markets. Results: The empirical analysis results are as follows. First, asymmetry of cost was observed in the case of the distribution industry. We confirm cost rigidity when sales decreased. Conclusions. This is the first study to look at cost behavior in the distribution industry, and the downward rigidity of cost in the distribution industry is observed.

• Steel and Composite Structures
• /
• v.14 no.4
• /
• pp.313-333
• /
• 2013

The web-encased steel-concrete composite (WESCC) beam is a new developed steel-concrete composite beam. Experiments of six simply supported WESCC beam specimens were conducted. The effects of the shear-span ratio and steel section type were all investigated on the static behaviors such as failure modes, failure mechanism and bearing capacity. The experimental results denoted that all specimens failed in bending mode and the degree of combination between the bottom armor plate of steel shape and concrete were very well without any evident slippage, which demonstrated that the function of bottom armor plate and web were fully exerted in the WESCC beams. It could be concluded the WESCC beams have high stiffness, high load carrying capacity and advanced ductility. The design methods are proposed which mainly consist the bearing capacity calculation of bending and flexural rigidity. The calculation results of the bearing capacity and deflection which take the shear deflection into account are in agreement with the experimental results. The design methods are useful for design and application of the innovative composite beams.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.34 no.1
• /
• pp.49-56
• /
• 1992

This study was carried out to investigate the mechanical behaviour of the plate on a Winkler's foundation according to the soil-structures relative stiffness and the applicability of the conventional analysis method. For the above purpose, Winkler's constant of 4, 15, 25 and 100kg/$cm^2$/cm was considered and the plate thickness of 20, 30, 50, 100 and 150cm was adopted. Results obtained from the numerical examples are summarized as follow: 1. The effects of elastic foundation is considerable for plates with small flexural rigidity. 2. As the Winkler's constant increases, the bending moment in the plate becomes localized near the loading point. 3. The stresses evaluated by the conventional method not correct even for rigid ground such as rock. 4. If the relative stiffness of the plate is very large, for example the plate thickness is larger than 100cm, the conventional analysis method can be justified for the design purposes. 5. On assumption the flexural rigidity of the plate is infinite, the interaction of soil and plate can be ignored in design consideration. The numerical examples in this paper show that when the plate thickness is more than 100cm, the effects of elastic foundation almost disappear. In practical design, soil-plate interaction should be taken into account, because the 100cm-thickness of the plate will not be practical value in usual sites.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.2
• /
• pp.78-83
• /
• 2016

The development of an exclusive 8-axis multi-tasking machine to finish multiple cutting processes by a single piece of power equipment for securing the high-precision machining and high productivity of the series of shafts (a core part of the automotive powertrain that delivers engine power) is needed. The rigidity of the structure must be improved and the weight of the structure must be reduced to develop a multi-tasking machine with high precision and high productivity. In this paper, we perform a static structural analysis of the initial design of the multi-tasking machines and compare the results of the multi-tasking machines improved by the reinforced design and the results of the initial one. According to the results of the structural analysis, the rigidity of the reinforced machine was increased and the overall weight was decreased. Therefore, the productivity was increased.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.6 s.144
• /
• pp.644-653
• /
• 2005

In general the loads due to ocean wave are considered as main design parameters governing the global structural safety of VLFS (Very Large Floating Structure). In order to predict design wave loads accurately, hydro-elastic analysis must be conducted considering the initial global flexural rigidity of VLFS. However, in order to determine the structural scantling of major members (deck, bottom, side panels and longitudinal / transverse BHD etc.), static load and design wave loads must be given as explicit form generally. Therefore in order to determine a proper structural arrangement and scantlings of VLFS at initial design stage, both calculations of structural scantling and hydro-elastic analysis for wave conditions must be conducted iteratively and the convergence of their results must be checked. On this paper, based on the case design of a 500×300 m size's floating marina resort, the details of structural design technique using hydro-elastic analysis are explained and discussed. At first, the environmental conditions and the system requirements of the design of marina resort are described. The scantling formulas for the major members of pontoon type VLFS are proposed from the local and global design points of view. Considering the design wave loads as well as static design loads, the structural safety is checked iteratively.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.3 s.55
• /
• pp.145-154
• /
• 2009

Steel-Concrete Composite Deck with I-beam welded is lighter and easier to construct than conventional in situ reinforced concrete slabs due to the I-beam embedded in the corrugated slab. For the calculation of effective flexural rigidity of conventional reinforced concrete structures, methods suggested in Design Standard for Roads and Bridges and ACI have been used. In this paper, the calculation methods were applied to steel-concrete composite deck with I-beam welded and then results of the steel-concrete composite deck were compared with those of reinforced concrete slabs. In addition, applicability of the methods to steel-concrete composite deck with I-beam welded was estimated. In order to compare the effective flexural rigidity, flexural experiments were conducted. Fifteen slabs were built and the variables considered in the experiments were studs, length of the slab, shape of the section and connecting methods.