• Current Photovoltaic Research
• /
• 제8권1호
• /
• pp.27-32
• /
• 2020

CuS thin films were deposited on glass substrates at room temperature by RF magnetron sputtering. The structural and optical properties of CuS thin films grown by varying RF-power from 40 W to 100 W were studied. From the XRD analysis, we confirmed hexagonal crystal structures grown in the preferred orientation of the (110) plane in all CuS thin films, and the intensity of the main diffraction peak increased in proportion to the increase of RF-power. In the case of CuS thin film deposited at 40W, small-sized particles formed a thin and dense surface morphology with narrow pore spacing, relatively. As the power increased, the grain size and grain boundary spacing increased sequentially. The peaks for the binding energy of Cu 2p_3/2 and Cu 2p_1/2 were determined at 932.1 eV and 952.0 eV, respectively. The difference in binding energy for the Cu²⁺ states was the same at 19.9 eV regardless of process parameters. The transmittance and band gap energy in the visible region tended to decrease with increasing sputtering powers.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1133-1136
• /
• 1995

RF-magnetron sputtering 방법으로 형성한 $BaTa_2O_6$의 공정변수에 따른 전기, 광학적 특성변화를 관찰하여 $BaTa_2O_6$ 박막의 TFELD(thin film electroluminescent display) 절연막으로서 응용 가능성을 연구하였다. $BaTa_2O_6$ 박막의 유전특성은 증착시의 $O_2$ 함량과 sputtering 압력의 변화에는 큰 영향을 받지 않으나 기판온도에는 영향을 받는 것으로 확인되었다. 이들 공정변수를 가변하여 실험한 결과, $BaTa_2O_6$ 박막 형성의 최적조건으로 플라즈마 압력을 6 mtorr, sputtering gas 내의 $O_2$ 혼합비율은 40%, 기판온도는 $100^{\circ}C$로 결정하였다. 이상의 조건에서 제조된 $BaTa_2O_6$ 박막은 10.2 ${\mu}C/cm^2$의 매우 우수한 성능지수를 보였다. 이상의 $BaTa_2O_6$ 박막을 하부절연층으로, 절연파괴강도가 높은 $SiO_xN_y$를 상부 절연층으로 사용하여 제조된 EL 소자는 1 kHz, 삼각파 구동시 발광 임계전압은 약 32 volts, 최대휘도는 54 $cd/m^2$으로 측정되었다.

• Transactions on Electrical and Electronic Materials
• /
• 제15권6호
• /
• pp.328-332
• /
• 2014

Thin film transistors (TFTs) with an amorphous silicon zinc tin oxide (a-2SZTO) channel layer have been fabricated using an RF magnetron sputtering system. The effect of the change of excitation electron on the variation of the total interfacial trap states of a-2SZTO systems was investigated depending on sputtering power, since the interfacial state could be changed by changing sputtering power. It is well known that Si can effectively reduce the generation of the oxygen vacancies. However, The a-2SZTO systems of ZTO doped with 2 wt% Si could be degraded because the Si peripheral electron belonging to a p-orbital affects the amorphous zinc tin oxide (a-ZTO) TFTs of the s-orbital overlap structure. We fabricated amorphous 2 wt% Si-doped ZnSnO (a-2SZTO) TFTs using an RF magnetron sputtering system. The a-2SZTO TFTs show an improvement of the electrical property with increasing power. The a-2SZTO TFTs fabricated at a power of 30 W showed many of the total interfacial trap states. The a-2SZTO TFTs at a power of 30 W showed poor electrical property. However, at 50 W power, the total interfacial trap states showed improvement. In addition, the improved total interfacial states affected the thermal stress of a-2SZTO TFTs. Therefore, a-2SZTO TFTs fabricated at 50 W power showed a relatively small shift of threshold voltage. Similarly, the activation energy of a-2SZTO TFTs fabricated at 50 W power exhibits a relatively large falling rate (0.0475 eV/V) with a relatively high activation energy, which means that the a-2SZTO TFTs fabricated at 50 W power has a relatively lower trap density than other power cases. As a result, the electrical characteristics of a-2SZTO TFTs fabricated at a sputtering power of 50 W are enhanced. The TFTs fabricated by rf sputter should be carefully optimized to provide better stability for a-2SZTO in terms of the sputtering power, which is closely related to the interfacial trap states.

• 한국진공학회지
• /
• 제5권2호
• /
• pp.139-146
• /
• 1996

rf 마그네트론 스파터링법을 이용하여 투명 전도성 Sb-doped $SnO_2$ 박막을 증착하였으나 박막표면에서 막손상현상이 발생하였다. 특히 기판 중심부 및 타게트 부식부위에 대응하는 부분에서 발생된 막손상을 방지하고자 , 환원형의 마스크 유리가 타게트표면에서 1.5cm지점에 설치되었다. 또한 마그네트론 스파터링의 작동조건인 rf전력, 스파터링 가스압력 및 기판온도를 최적으로 조절하면서 박막의 균일성과 전기적 특성을 평가하였다. 작동조건을 이용한 실험결과에서 균일하고 막손상이 없는 박막을 증착하는 최적온도는 압력 변화에 따라 변하며, 비율은 50w의 rf전력에서 5mTorr당 약 $100^{\circ}C$정도였다. 유사하게 rf 전력？ md가에 대한 보상에서 최적온도는 적절한 비율로 내려간다.

• 반도체디스플레이기술학회지
• /
• 제9권4호
• /
• pp.83-86
• /
• 2010

The transparent electrode properties of ITO films deposited by RF magnetron sputtering with process pressure were investigated. The ITO thin films was deposited on a glass substrate using a target with 3in diameter sintered at a ratio of $In_2O_3$ : $SnO_2$ (9 : 1). 200-nm-thick ITO thin films were manufactured by various process pressures ($2.0{\times}10^{-2}$, $7.0{\times}10^{-3}$ and $2.0{\times}10^{-3}$ Torr). The optical transmittance and resistivity of the deposited ITO thin films showed a relatively satisfactory result under $10^{-2}$ Torr. For high process pressure, the optical transmittance was below 80%, while for low process pressure, the optical transmittance was above 85%. As a result of of mobility, resistivity and carrier concentration by Hall measurement, we obtained satisfactory properties to apply into a transparent conducting thin film.

• 한국안광학회지
• /
• 제3권1호
• /
• pp.115-120
• /
• 1998

RF(radio-frequency) magnetron 스퍼터링 장치에 질소가스와 아르곤가스를 동시에 주입하면서 Ti 타켓을 스퍼터링하여 $TiN_x$ 박막을 유리기판위에 제작하였다. 박막제작시 RF power supply 출력을 240W로, 증착기 내부의 온도는 $200^{\circ}C$를 유지하였다. $TiN_x$ 박막은 알곤 가스를 20sccm으로 고정시킨 상태에서 질소를 3sccm부터 9sccm까지 변화시켜가며 증착시켰다. 이때 박막의 화학적 조성과 성분비를 분석하기 위하여 XPS를 사용하였다.

• 한국안광학회지
• /
• 제4권1호
• /
• pp.21-25
• /
• 1999

RF(radio-frequency) magnetron 스퍼터링 장치에 질소가스와 아르곤가스를 동시에 주입하면서 Ti 타켓을 스퍼터링하여 TiN, 박막을 유리기판위에 제작하였다. 박막제작시 RF power supply 출력은 240W로, 증착기 내부의 온도는 $200^{\circ}C$를 유지하였다. TiN, 박막은 알곤 가스를 20sccm으로 고정시킨 상태에서 질소를 3sccm부터 9secm까지 변화시켜가며 증착시켰다. 이때 박막의 면저항과 화학적 조성과의 관계를 분석하기 위하여 XPS depth profiling과 4점 탐침법을 사용하였다.

• 한국재료학회지
• /
• 제16권7호
• /
• pp.445-448
• /
• 2006

Highly c-axis oriented ZnO thin films were grown on Si(100)substrates with Zn buffer layers. Effects of the Zn buffer layer thickness on the structural and optical qualities of ZnO thin films were investigated using X-ray diffraction (XRD), photoluminescence (PL) and Atomic force microscopy (AFM) analysis techniques. It was confirmed that the quality of a ZnO thin film deposited by rf magnetron sputtering was substantially improved by using a Zn buffer layer. The highest ZnO film quality was obtained with a Zn buffer layer 110 nm thick. The surface roughness of the ZnO thin film increases as the Zn buffer layer thickness increases.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권2호
• /
• pp.73-78
• /
• 2004

AIN thin film has been deposited on the $AI_2$$O_3$substrate with reactive radio frequency( RF) magnetron sputtering method. In this work, elelctromechanical coupling coefficient of AIN thin film was increased with an increase of AIN thin film thickness, and the maximum value was 0.11%. Insertion loss of SAW device was decreased with an increase of AIN thin film thickness and the minimum value was 33［㏈］. SAW velocity of IDTs/AIN/$AI_2$$O_3$structure and IDTs/AIN/$AI_2$$O_3$/Si structure were about 5480［㎧］and 5040［㎧］respectively.

• 한국전기전자재료학회논문지
• /
• 제33권6호
• /
• pp.450-453
• /
• 2020

In this study, ZnO:Ga thin films were fabricated on a glass substrate using various Ar flows by an RF magnetron sputter system at room temperature. The dependencies of Ar flow on different properties were investigated. An appropriate control over the Ar flow led to the formation of a high-quality thin film. The ZnO:Ga films were formed as a hexagonal wurtzite structure with high (002) preferential orientation. The films exhibited a typical columnar microstructure and a smooth top face. The average transmittance was 85~89% within the visible area. By decreasing the Ar flow, the sheet resistance was decreased due to an increase in the grain size and a decrease in the root mean square roughness. The lowest sheet resistance of 86 Ω/□ was obtained at room temperature for the 40 sccm Ar flow.