• 한국강구조학회 논문집
• /
• 제15권5호통권66호
• /
• pp.571-578
• /
• 2003

본 논문에서는 중심가새골조 가운데 가정 널리 사용되는 역V형 철골 가새골조의 내진거동을 탄소성 후좌굴해석에 의해 고찰하고, 압축가새의 좌굴이 최초로 발생한 층에 소성화가 집중되는 약층화 현상을 완화할 수 있는 효과적 내진보강 방안을 제시하고자 하였다. 즉 좌굴이 발생한 층에 집중되는 비탄성변형을 건물전체로 재분재하는 기능을 갖는 인장재(tie bar)를 삽입하여 내진성능을 효과적으로 개선할 수 있음을 입증하였다. 아울러 압축가새의 좌굴발생 순서를 감안하여 보강 인장재를 경제적으로 설계할 수 있는 실용적 설계방안을 제시하였다.

• 한국압력기기공학회 논문집
• /
• 제7권3호
• /
• pp.1-7
• /
• 2011

The analysis shows that the vibration is one of the main reasons of turbine failure. Especially, the problems caused by vibration occur right after retrofit of the turbine-generator and restarting the turbine. Through the case study of high vibration caused by after the turbine trip and restart, turbine vibration was identified to be influenced by startup condition. Turbine startup at high casing temperature right after unscheduled turbine trip cause radial expansion in rotor by contraction in axial direction, while casing continues to contract by steam flowing into casing. Consequently, gap between rotor and casing decrease until to metal contact to cause high vibration. Through the case study of high vibration of turbine-generator system after generator retrofit, it was identified that generator replacement could cause high vibration in turbine-generator system if the influence of generator replacement on entire system was not considered properly. To prevent startup delay caused by high vibration, it is important to keep the gaps at the design standard and start the turbine after thermal equilibrium.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 봄 학술발표회 논문집
• /
• pp.571-578
• /
• 1997

In the repair and repair works, epoxy resins are widely used as repair materials. The successful concrete repairs and retrofit works depends on the quality of the repair and retrofit materials. Although many materials for the repairs and retrofit have been developed in many contries, information on the repair methods are somewhat limited. Futhermore, the repairs and retrofit methods are also largely dependent on those froms in other developed contries, it is necessary to initiate rather fundamental repair-related research. The purpose of this study is to investigate th physical and mechanical properties of epoxy resin which is commonly used in repairing concrte crack in RC structures. The basic physical properties such as specific gravity, gel point and shrinkage ratio as well as the mechanical properties such ad the tensile and compressive strength, elastic modulus were acquired by the standard test method (KS code). For the test results, the great deviations of physical and mechanical properties among the test materials were discovered and is, therefore, recommended that careful attentions should be give in selecting the epoxy resin by considering the characteristics of the repair materials and repair works.

• 설비공학논문집
• /
• 제24권9호
• /
• pp.663-670
• /
• 2012

Recently, energy saving in building sector is of great important to meet national $CO_2$ reduction goals in Korea. In this sense, it is crucial to improve the energy performance for existing building. The energy efficiency investments, ESCO business, can be beneficial to expand the chance of energy retrofit for existing building. However, ESCO business hardly expand in Korea because it has many limitations in guarantee for energy saving. Also, it is more difficult to apply the energy retrofit measures in existing building than new building. Therefore, the retrofitting methods for existing small-and medium-sized buildings should be improved to initiate ESCO business and expand it in Korea. In this study, the energy retrofit methods for small sized office building were suggested and the case study for a small sized office building located in Suwon was accomplished.

• 한국환경보건학회지
• /
• 제33권1호
• /
• pp.36-42
• /
• 2007

Diesel PM can be controlled using Diesel Particulate Filter, which can effectively reduce the level of soot emissions to ambient background levels. In the Heavy Duty Diesel area, the Continuously Regeneration trap has been widely applied in the retrofit market. As the Special act for the improvement of air quality in the capital area, the retrofit program for DPF to used diesel vehicle has progressed favorably and there are currently over 1,000 of these DPF in use in retrofit applications in korea. These DPF comprise a specially formulated Diesel Oxidation Catalyst upstream of a DPF. The $NO_2$ generated by the DOC is used to combust the carbon collected in the DPF at low temperature. To certificate DPF device that is suitable to domestic circumstances, it is necessary to evaluate exactly the DPF devices according to the regulation of DPF certificate test procedure for retrofit(ministry of environment(MOE) announcement NO. 2005-16). To do so the understand of that regulation like the standard of PM reduction rate is needed. In this study the test procedure including test cycle and BPT test condition was examined and also the test result for specific DPF was analyzed. In every test like field test, PM reduction efficiency test and seoul-10 mode test, no defect could be showed.

• 한국구조물진단유지관리공학회 논문집
• /
• 제11권5호
• /
• pp.71-80
• /
• 2007

기존 시멘트에 비해 우수한 인장변형성능을 가지는 고인성 시멘트 복합체(HPFRCC)를 보수, 보강에 적용 시키려는 연구가 최근 활발히 진행되고 있다. 본 연구에서는 HPFRCC의 일종인 ECC와 초속경 숏크리트인 MDF의 보강성능을 알아보고자 한다. 실험체는 실존하는 철근콘크리트 구조물의 전단벽을 1/2 축소하여 제작하였으며 개구부를 가지고 있다. 실험결과 WB-MDF, ECC는 WB-0.23에 비해 각각 28.4%, 48.4%의 강도증가를 보였으며, 특히 WB-ECC가 WB-MDF에 비해 연성면에서 우수하게 나타났다.

• 한국지진공학회논문집
• /
• 제8권2호
• /
• pp.9-17
• /
• 2004

기존 교량 중 내진 설계가 되어 있지 않은 교량의 내진 성능에 관한 평가는 향후 발생 가능한 지진에 대한 대비로써 중요하다. 성능평가 결과, 소요의 내진 성능을 보유하고 있지 못하다면 그에 대한 보강이 필요하며 보강방법으로는 여러 가지가 있다. 그 중 지진격리증기를 이용한 내진 보강은 교량에서 교각이나 기초 등에 추가적인 시공 없이 기존 받침을 교체함으로써 비교적 간단하게 수행할 수 있다. 본 논문에서는 최근 그 시공사례가 증가하고있는 지진격리증기를 기존 비내진 교량의 보강에 사용할 때 교량의 내진 성능향상을 합리적으로 규명하기 위해 기존상태의 교량 및 지진격리장치로서 내진 보강된 교량의 내진 성능을 비교하였다. 이를 위해 기존 교량 및 내진 보강된 교량에 대해 비선형 정적ㆍ동적 해석을 수행하였으며 목표 수준의 지진에 대하여 각각의 응답을 산정하고 이를 비교하여 내진 성능 향상을 확인하였다.

• 설비공학논문집
• /
• 제26권8호
• /
• pp.394-400
• /
• 2014

Several models and methods have been developed to verify the improvement of energy performance in retrofit buildings. The verification is important to confirm the effectiveness of new technologies or retrofits. Inverse model toolkit proposed by ASHRAE evaluates the changes of the energy performance of retrofit buildings by using actual energy consumption data. In this study, the inverse model toolkit was used to analyze heating and cooling energy performance of an office building. Analyzed coefficients of correlation of actual energy consumption with estimated energy consumption was above 0.92 and well fitted. It was confirmed that energy consumption of natural gas decreased by 43.4% and also that electricity decreased by 13.8%, after the retrofit of the case building. For the energy usage, cooling energy was increased by 7.4%, heating energy was decreased by 42.3%, hot water and cooking were increased by 3.4%, lighting and electronics were decreased by 19.3%, and the total energy was decreased by 18.9%.

• 한국태양에너지학회 논문집
• /
• 제38권3호
• /
• pp.29-36
• /
• 2018

The goal of this study is to retrofit the windows of residential buildings and to activate the green remodeling by verifying energy saving and indoor thermal environment. As a result of analysis of the energy saving effect of 458 units window retrofits, it was possible to reduce the energy requirement by 48.20% ~ 54.97%. According to the improvement on indoor environment, it was possible to operate by reducing heating temperature and supply time. The actual gas consumption of the heating period was reduced by 25% compared with that of the window retarder to save 28,968 thousand won of heating energy cost. Resident's satisfaction surveys were conducted one year after window retrofit. More than 80% of the respondents answered that they satisfied the improvement on window performance, indoor thermal environment and indoor sound environment. As a result, we verified the energy saving effect and the improvement on the indoor environment through window retrofits.

• 한국공간구조학회논문집
• /
• 제20권4호
• /
• pp.131-139
• /
• 2020

In this paper, the hybrid prefabricated retrofit method is suggested and examined. Six specimens were manufactured in order to evaluate their flexural performance of RC beams. Test parameters include the added beam depth, the thickness of bottom plate, the number of the steel plate with openings. The effects of these parameters on the flexural performance of reinforced concrete beams were examined. The load-deflection behavior and modes of cracks are presented from the test results. At the test result, the flexural capacity and the ductility of the hybrid prefabricated retrofit method was increased satbly. Also, comparing the flexural performance of RC beam and retrofitted RC beams, it was increased that the flexural strength is about 3.3 times, the ductility is about 2.55 times, and energy dissipation capacity is about 7.34 times.