• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.2
• /
• pp.283-288
• /
• 1996

This paper presents the development technology of standard shielded resistor divider for full lightning impulse voltage. The ability of large-capacity power apparatus to withstand lighting stroke is usually evaluated by means of full lightning impulse voltage. Lightning impulse voltage test has been essential to evaluate the insulation performance of electrical power apparatus. Recently international standard (IEC 60) on high voltage measurement techniques is being revised and requests a formal traceability of high voltage measurements. Therefore, general interest for this area has grown considerably during last years, and several international intercomparisons have already completed worldwide, i.e. Europe, Japan, America etc., In this viewpoint, we have also investigated the step response of the standard shielded resistor divider, which satisfies the IEC recommendation.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1948-1949
• /
• 2007

This paper presents the characteristics and effects of grounding resistor and impedance. In grounding system, Grounding resistor is governed neutral currents and voltage. It seems that, grounding resistor has 0 value, then circuit has no faults. While if grounding resistor has large value, then neutral current has large value of fault current and it is made a damage to the utility. In order to analyze the grounding impedance characteristic, EMTP simulation has been used. The grounding impedance characteristic has been analyzed and tested for various grounding arrangements and electrode circuit shapes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.23-25
• /
• 2005

Infrared bolometer sensor's variation is detected by voltage drop between reference resistor and bolometer resistor in this architecture. One of the serious problems in this architecture is that these resistors value has a process variation. So common-mode level could be different from expectation in room temperature. Different common-mode level could lead to wrong output at the end of readout circuit. We suggest useful method to solve this problem. Difference correction using capacitor has reduced CM level difference to 86% for 1 $M\Omega$. bolometer and reference resistor's 10% variation.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.306-307
• /
• 2010

본 논문에서는, 동기 전동기 구동을 위해 Three Shunt Resistor를 이용하여 전류를 피드백 받는 방법에 대하여 분석한다. 특히 Three Shunt Resistor를 이용하여 전류를 피드백 받는 경우 Modulation Index (MI)의 크기에 따라 피드백 받은 상전류 정보의 왜곡이 발생하는 문제점에 대하여 분석하고 이를 해결하기 위한 새로운 방법을 제안하며, 컴퓨터 시뮬레이션을 통하여 검증한다.

• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.411-416
• /
• 2010

In this research, we intended to improve the tolerance of thick film resistor using photosensitive polymer resistor paste which was fabricated with alkali-solution developable photosensitive resin and conductive carbon black. At first, we investigated the effect of the selection of carbon black and photosensitive resin on the resistance range and tolerance level of polymer thick film resistor (PTFR). And then, a difference in resistance tolerance was evaluated according to the coating methods of photosensitive resistor paste on test board. In case that the photosensitive resistor paste was coated on whole surface of test board using screen printing, large positional tolerance was obtained because the formation of the thick film with uniform thickness was difficult. On the other hand, when the paste was coated with roller, the resistive thick film with uniform thickness was formed on the whole board area and the result of resistance evaluation showed low tolerance in ${\pm}10%$ range. The tolerance of PTFR could be improved by combination of the precise patterning using photo-process and the coating process for the resistive thick film with uniform thickness.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1983.04a
• /
• pp.45-47
• /
• 1983

In integrated circuit, for a saving in total chip area per circuit, stably high value resistor was fabricated. Hence this paper explained that the measurement and fabrication of high value semiconductor resistor using ITO thin film. It is also used special material and new method fabrication.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.598-599
• /
• 2017

In motor application, High efficiency is important. So Design engineer select small gate resistor for lower switching. But There is side effect with small gate resistor. It makes large dv/dt and system request large EMI filter. It makes price increase. This paper introduce about gate drive IC which have solution both of lower loss and EMI issue.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.11
• /
• pp.2495-2502
• /
• 2012

This paper presents a new structure of phase looked loop (PLL) for replacing a process sensitive resistor in loop filter with an additional charge pump (CP). The additional charge pump works as a resistor in a loop filter. The output of two charge pumps changes same direction according to process variation. The simulation results according to process conditions(SS/TT/FF) demonstrate that the proposed PLL works properly with process variations. It has been designed with a 1.8V $0.18{\mu}m$ CMOS process and proved by simulation with HSPICE.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.2
• /
• pp.133-138
• /
• 2014

This paper proposes a low power-loss averaging current mode control using a resistor and bypass switch. Generally, current sensing method using a resistor has a disadvantage of power loss which degrades the efficiency of the entire systems. On the other hand, proposed measurement technique operating with bypass-switch connected in parallel with sensing resistor can reduce power loss significantly the current sensor. An analog-circuited bypass driver is implemented and used along with an average-circuit mode controller. The bypass switch bypasses the sensing current with a small amount of power loss. In this paper, a 50[W] prototype average current mode boost converter has been implemented for the experimental verification.

• Journal of Veterinary Clinics
• /
• v.35 no.5
• /
• pp.206-210
• /
• 2018

The purpose of this study was to evaluate the reliability and validity of the Force-Sensing Resistor (FSR) for measurement of static hindlimb weight distribution in beagle dogs and to compare these results to a Digital Weighing Scale (DWS). Nine healthy beagle dogs were recruited for this study. Static weight distribution was evaluated four times at intervals of 5 days with each device and two observers to calculate the intra- and interobserver reliability. The intraclass correlation coefficient (ICC) values of the FSR for intraobserver reliability were moderate to good (0.74). The results for the DWS showed poor to moderate (0.56) ICC values for intraobserver reliability. The ICC values for interobserver reliability were 0.53 and 0.61 for FSR and DWS, respectively, indicating poor to moderate agreement. Our findings suggest that the Force-Sensing Resistor can be used to measure static weight distribution in veterinary medicine. However, caution should be taken when comparing measured values of static weight distribution obtained utilizing both the FSR and DWS due to their low positive correlation (R = 0.41, p < 0.01).