• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.32-38
• /
• 1998

In order to investigate the relationship between the stiffness and structure of the automotive roof panels, two kinds of glass fiber reinforced plastic(GFRP) roof panels without and with insert material were fabricated by resin transfer molding(RTM) method. The stiffness test was performed at the same condition as it of actual driving. The structural design and material selection for improving the recyclability of GFRP roof panels were also covered.

• Korea-Australia Rheology Journal
• /
• v.12 no.1
• /
• pp.83-92
• /
• 2000

In resin transfer molding (RTM) process, preplaced fiber mat is set up in a mold and thermoset resin is injected into the mold. An important interest in RTM process is to minimize cycle time without sacrificing part quality or increasing cost. In this study, the numerical simulation and optimization process in filling stage were conducted in order to determine the optimum gate locations. Control volume finite element method (CVFEM) was used in this numerical analysis with the coordinate transformation method to analyze the complex 3-dimensional structure. Experiments were performed to monitor the flow front to validate simulation results. The results of numerical simulation predicted well the experimental results with every single, simultaneous and sequential injection procedure. We performed the optimization analysis for the sequential injection procedure to minimize fill time. The complex geometry of an automobile bumper core was chosen. Genetic algorithm was used in order to determine the optimum gate locations with regard to 3-step sequential injection case. These results could provide the information of the optimum gate locations in each injection step and could predict fill time and flow front.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.04a
• /
• pp.223-231
• /
• 1997

내열성복합재료와 Steel 구조물 사이의 좁고 긴 원통형 공간을 내열성 폴리우레탄 재료로 충전하는 연구를 수행하였다. 충전재료를 결정하기 위하여 3종의 폴리우레탄과 에폭시수지를 선정, 시험하여 내열성, 흐름성, 접착성, 경도측정 등을 통하여 최종 결정하였으며 선정된 폴리우레탄을 충전하기 위하여 Resin Transfer Molding(RTM) 방법을 사용하였다. 충전 공정의 적용여부를 판단하기 위하여 아크릴을 이용한 RTM치구를 설계, 제작하여 시험하였다. 충전된 조립체는 비파괴 검사를 통하여 접착, 기공 등을 검사하였으며 지상연소시험을 통하여 내열성능을 평가하였다.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.134-136
• /
• 2005

Homogenization method is adopted to predict the permeability tenor for glass fiber plain woven fabrics. Calculating the permeability tensor numerically is an encouraging task because the permeability tensor is a key parameter in resin transfer molding (RTM). Based on multi-scale approach of the homogenization method, the permeability for the micro-unit cell within fiber tow is computed and compared with that obtained from flow analysis for the same micro-unit cell. It is found that they are in good agreement. In order to calculate the permeability tensor of macro-unit cell for the plain woven fabrics, the Stokes and Brinkman equations which describe inter-tow and intra-tow flow respectively are employed as governing equations. The effective permeabilities homogenized by considering intra-tow flow are compared with those obtained experimentally. Control volume finite element method (CVFEM) is used as a numerical method. It is shown that the asymptotic expansion homogenization method is an attractive method to predict the effective permeability for heterogeneous media.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.83-86
• /
• 2003

Complete prediction of second order permeability tensor for three dimensional preform such as plain woven fabric and braided preform is critical to understand the resin transfer molding process of composites. The permeability can be obtained by various methods such as analytic, numerical, and experimental methods. For several decades, the permeability has studied numerically to avoid practical difficulty of many experiments. However, the predicted permeabilities are a bit wrong compared with experimentally measured data. In this study, numerical calculation of permeability was conducted for two kinds of preforms i.e., plain woven fabric and circular braided preform. In order to consider intra-tow flow in the unit cell of preform the proposed flow coupled model was used for plain woven fabric and the Brinkman equation was solved in the case of the braided preform.

• Composites Research
• /
• v.30 no.3
• /
• pp.169-174
• /
• 2017

Demand of glass fiber reinforced composites (GFRC) increased with developing aircraft and defense industries using resin transfer molding (RTM) process to produce complex product. In this research, wetting, interfacial, and mechanical properties were evaluated with different Cross-linking Density by Molecular Weight of Hardener. Epoxy resin as matrices was used bisphenol-A type and amine-type hardeners with different molecular weight. Specimens were manufactured via RTM and wetting property of resin and glass fiber (GF) mat was evaluated to viscosity of epoxy and injection time of epoxy matrix. Mechanical property of GFRC was determined via flexural strength whereas interfacial properties were determined by interlaminar shear strength (ILSS) and interfacial shear strength (IFSS). The difference in mechanical property depends upon the fiber weight fraction (wt %) of GFRC by RTM as well as the different Molecular Weight of Hardener.

• Fibers and Polymers
• /
• v.4 no.3
• /
• pp.135-144
• /
• 2003

Permeability of the preform is one of key factors in design of RTM (Resin Transfer Molding) mold, determination of processing conditions, and modeling of flow in the mold. According to previous studies, permeability measured in the unsaturated fiber mats are higher than that in the saturated fiber mats by about 20% because of the capillary pressure. In this study, permeabilities of several fiber preforms are measured for both saturated and unsaturated flows. A saturated experiment of radial flow has been adopted to measure the permeability of anisotropic fiber preforms with high fiber content, i.e., circular braided preforms. In this method, four pressure transducers are used to measure the pressure distribution. Permeabilities in different directions are determined and the experimental results show a good agreement with the theory. Since permeability is affected by the capillary effect, permeability should be measured in the unsaturated condition for the textile composites to be manufactured under lower pressure as in the Vacuum Assisted Resin Transfer Molding (VARTM).

• Composites Research
• /
• v.12 no.2
• /
• pp.70-81
• /
• 1999

Resin transfer molding(RTM) as a composite manufacturing process is currently of great interest in the aerospace industry requiring high performance composite parts. In this study, an analysis of mold filling in the RTM process was carried out by numerical simulation using finite element/control volume technique. Experimental work for the visualization of resin flow through fibrous preform was also conducted in order to quantitatively measure the permeabilities of the fiber mats and to evaluate the validity of the developed numerical code. The different types of fiber mats and silicon oils were selected as reinforcements and resin materials, respectively. The effects of fibrous preform structure, mold geometry, and preplaced insert on the flow front patterns during mold filling were examined by integrating the model predictions and experimental results. The flow fronts predicted by numerical simulation were in good agreement with those observed experimentally. However, according to the regions of the mold, some deviations between predicted and observed flow fronts could be found because of non-uniform fiber volume fraction. Weldline locations for the resin flow through round insert preplaced in the mold could be qualitatively deduced based on predicted flow fronts.

• Applied Chemistry for Engineering
• /
• v.32 no.4
• /
• pp.449-455
• /
• 2021

Composite materials are substances that are configured to have excellent physical properties by combining the properties of a single substance, and are in the limelight as materials that exceed the performance of metals and polymers. However, it has the disadvantages of long cycle time and high unit price, and much research is being performed to overcome these disadvantages. In this study, we developed an epoxy resin curing agent that can shorten the time required for mass production of composite materials, and tried to expand the applicability of objections by imparting flame retardancy. The epoxy resin used as a basic substance utilized two types of bisphenol F and resorcinol structure, which was further modified using 9,10-dihydro-9-oxa-10-phosphaphenantrene-10-oxide (DOPO) to impart flame retardancy. Triethylphosphate (TEP) and bis [(5-ethyl-2-methyl-1,3,2-dioxaphosphorinan-5-yl)methyl] methyl phosphonate P,P'-dioxide (FR-001) were used as additives, seven kinds of compositions were blended, thermal characteristics (gelation time, glass transition temperature) and flame retardant performance were evaluated. We successfully developed an epoxy matrix that can be applied to high pressure resin transfer molding (HP-RTM) process.

• Composites Research
• /
• v.28 no.6
• /
• pp.372-377
• /
• 2015

In this study, we analyzed process numerically when a bogie frame skin is manufactured by applying resin transfer molding process using composite material instead of steel. Processing time was compared based on the various thickness of bogie frame skin and the weight variation of a skin was also considered. As a result, RTM processing time decreases and the weight of a bogie reduces as the thickness of frame skin increases with the assumption that fiber volume is constant inside the skin. By considering these results as the information to estimate the production cost, trade-off between two fields, processing time and structural properties, can be performed in design optimization to produce bogie frame.