• 한국시뮬레이션학회논문지
• /
• 제11권3호
• /
• pp.49-58
• /
• 2002

It takes 2 or 3 months to manufacture memory device. Defect has to exist owing to hundreds of processes. If there are too many defects, the memory has to be rejected. But if there are a few defects, it will be more efficient and cost reducing for the company to use it by repairing. Therefore, laser-repair process is needed for such a reason and redundancy analysis is needed to establish correct target of laser-repair process. The equipment development company had provided the redundancy analysis and each development company had developed and provided separately. So, to analyze the similar type of defects, redundancy analysis time can be very different by the manufacture. The purpose of this research is to strengthen the competitive price and to apply correlation concept in business for reducing the redundancy analysis time to repair the defects

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 가을학술발표대회논문집
• /
• pp.107-108
• /
• 2023

In this study, the tensile adhesion strength was evaluated according to KS F 4932 to assess the suitability of MMA-based repair materials for concrete roads. Two types of MMA were used. Mortar mock-ups were made and tested for adhesion strength in three different surface conditions: air, water, and salt water. Both showed strengths above the standardized strength of 0.6 MPa. Type B, which has a relatively low adhesion strength, is considered more suitable.

• Journal of Chest Surgery
• /
• 제22권4호
• /
• pp.630-637
• /
• 1989

Author studied 30 cases of remained heart murmur patients after VSD repair. The age ranged from 7months to 27 years, and sex ratio was 29: 1 in male and female. Perimembranous trabecular type of VSD was the most common causes of remained murmur after operation 11 cases, and the next was subpulmonic type 9 cases. The VSD size between 1.1 and 2.0cm in diameter was the most common in 15 cases. The operative method frequently used was patch closure in 21 cases, and commonly used surgical approaching way was through right atrium. Mechanisms of origin of postoperative remained murmur was from TR 9 cases, PI 6 cases, PS 5 cases, remnant shunts 5 cases, pulmonary artery dilatation 2 cases, MR 2 cases, and subaortic stenosis 1 cases.

• Journal of Chest Surgery
• /
• 제44권6호
• /
• pp.427-431
• /
• 2011

Successful thoracic endovascular repair for complicated Stanford type B acute aortic dissection in two patients is herein reported. The true lumen flow was immediately restored following stent graft deployment in the descending thoracic aorta with subsequent resolution of the distal malperfusion syndrome. One patient is doing well more than 15 months after surgery and another patient who was treated more recently is also doing well 7 months postoperatively.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.305-308
• /
• 2006

This paper is to investigate the strength, impact endurance and shrinkage of wet spraying type fiber composite mortar for repair material depending on fiber type and product kinds. Fiber composite mortar containing PVA fiber had the highest strength compared to that using any other fiber. Especially, The use of PVA fiber results in a remarkable enhancement in impact strength and an improved volumetric stability. Accordingly, it is confirmed that fiber composite mortar containing PVA fiber has remarkable performance as repair material of damaged section of concrete.

• Journal of Chest Surgery
• /
• 제49권4호
• /
• pp.298-301
• /
• 2016

Thoracic endovascular aortic repair (TEVAR) has emerged as an effective therapy for a variety of thoracic aortic pathologies. However, various types of endoleak remain a major concern, and its treatment is often challenging. We report a case of type I endoleak occurring 19 months after zone II hybrid TEVAR. The endoleak was successfully repaired by the frozen elephant trunk technique, without removal of a previous stent graft, combined with ascending aorta and total arch replacement.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2003년도 학술.기술논문 발표회
• /
• pp.37-40
• /
• 2003

This present paper mainly contains adhesion part disconnection type exposure composition waterproof method using embossing PVC sheet. The existing polymer resin coating and sheet waterproofing construction method have, however, some weak point such as being decrease life cycle of concrete with water leaking from materials be affected by crack and movement dash bond concrete through the whole-adhere construction. Above the reason, this paper has particular method increasing crack-defending performance from stress occurred concrete movement by part disconnection, adds maintain waterproofing performance subordinate sheet, that can be contributed a convenience of maintenance which is decreasing industrial waste and repair construction cycle through the part repair in case of leaking water.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 추계 학술논문 발표대회
• /
• pp.79-83
• /
• 2005

In the reinforced concrete structure, Even if speak that water leakage occurrence is no problem to material, there is a lot of reasons construction factor, material damage by behavior structure, properties of matter change by years and water leakage part by environment condition. so, waterproofing technological consideration should be gone ahead. In this research, we will study about stick performance, concrete surface adhesive, damage and blow. we will check all things and test it. The stick expansion type complex of flexible material passed on result of standard. It is conducive to concrete of durability by waterproofing layer performance demobilitation technology on the water leakage structure for solution of problem and repair

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2003년도 학술.기술논문발표회
• /
• pp.37-40
• /
• 2003

This present paper mainly contains adhesion part disconnection type exposure composition waterproof method using embossing PVC sheet. The existing polymer resin coating and sheet waterproofing construction method have, however, some weak point such as being decrease life cycle of concrete with water leaking from materials be affected by crack and movement dash bond concrete through the whole-adhere construction. Above the reason, this paper has particular method increasing crack-defending performance from stress occurred concrete movement by part disconnection, adds maintain waterproofing performance subordinate sheet, that can be contributed a convenience of maintenance which is decreasing industrial waste and repair construction cycle through the part repair in case of leaking water.

• The Journal of Advanced Prosthodontics
• /
• 제12권5호
• /
• pp.322-328
• /
• 2020

PURPOSE. This study evaluated the shear bond strength between 3D printed provisional resin and conventional provisional resin depending on type of conventional provisional resin and different surface treatments of 3D printed resin. MATERIALS AND METHODS. Ninety-six disc-shaped specimens (Ø14 mm × 20 mm thickness) were printed with resin for 3D printing (Nextdent C&B, Vertex-Dental B. V., Soesterberg, Netherlands). After post-processing, the specimens were randomly divided into 8 groups (n=12) according to two types of conventional repair resin (methylmethacrylate and bis-acryl composite) and four different surface treatments: no additional treatment, air abrasion, soaking in methylmethacrylate (MMA) monomer, and soaking in MMA monomer after air abrasion. After surface treatment, each repair resin was bonded in cylindrical shape using a silicone mold. Specimens were stored in 37℃ distilled water for 24 hours. The shear bond strength was measured using a universal testing machine at a crosshead speed of 0.5 mm/min. Failure modes were analyzed by scanning electron microscope. Statistical analysis was done using one-way ANOVA test and Kruskal-Wallis test (α=.05). RESULTS. The group repaired with bis-acryl composite without additional surface treatment showed the highest mean shear bond strength. It was significantly higher than all four groups repaired with methylmethacrylate (P<.05). Additional surface treatments, neither mechanical nor chemical, increased the shear bond strength within methylmethacrylate groups and bis-acryl composite groups (P>.05). Failure mode analysis showed that cohesive failure was most frequent in both methylmethacrylate and bis-acryl composite groups. CONCLUSION. Our results suggest that when repairing 3D printed provisional restoration with conventional provisional resin, repair with bis-acryl composite without additional surface treatment is recommended.