• Economic and Environmental Geology
• /
• v.53 no.5
• /
• pp.529-542
• /
• 2020

The cesium (Cs) sorption characteristics of a bead-type polysulfone carrier contained HNO₃-treated bamboo charcoal (3 - 5 mm in diameter) in water system were investigated and its Cs removal efficiency as an adsorbent from water was also identified by various laboratory experiments. From the results of batch sorption experiments, the bead-type polysulfone carrier with only 5% HNO₃-treated bamboo charcoal (P-5NBC) represented the high Cs removal efficiency of 57.8% for 1 hour sorption time. The Cs removal efficiency of P-5NBC in water after 24 hours reaction maintained > 69% at a wide range of pH and temperature conditions, attesting to its applicability under various water systems. Batch sorption experiments were repeated for P-5NBC coated with two cultivated microorganisms (Pseudomonas fluorescens and Bacillus drentensis), which were typical indigenous species inhabited in soil and groundwater. The Cs removal efficiency for two microorganisms coated polysulfone carrier (BP-5NBC) additionally increased by 19% and 18%, respectively, compared to that of only P-5NBC without microorganisms coated. The average Cs desorption rate of P-5NBC for 24 h was lower than 16%, showing the Cs was stably attached on HNO₃-treated bamboo charcoal in so much as its long-term use. The maximum Cs sorption capacity (q_m) of P-5NBC calculated from the Langmuir isotherm model study was 60.9 mg/g, which was much higher than those of other adsorbents from previous studies for 1 h sorption time. The results of continuous column experiments showed that the P-5NBC coated with microorganisms packed in the column maintained > 80% of the Cs removal efficiency during 100 pore volumes flushing. It suggested that only 14.7 g of P-5NBC (only 0.75 g of HNO₃ treated bamboo charcoal included) can successfully clean-up 7.2 L of Cs contaminated water (the initial Cs concentration: 1 mg/L; the effluent concentration: < 0.2 mg/L). The present results suggested that the Cs contaminated water can be successfully cleaned up by using a small amount of the polysulfone carrier with HNO₃-treated bamboo charcoal.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.12
• /
• pp.1347-1352
• /
• 2005

[ $H_2S$ ] removal reaction using $Li_2ZrO_3/honeycomb$ has been carried out in a fixed bed reactor for the cleaning of syngas from the waste gasifier. $Li_2ZrO_3$ was synthesised using reagent-grade $Li_3CO_3$ and $ZrO_2$ with suitable amount of ethanol in a 1:1 ratio. And then $Li_2ZrO_3$ were calcined in air at $850{\sim}1000^{\circ}C$ for 14 h. The optimum condition of $H_2S$ removal reaction is around 20 wt% $Li_2ZrO_3$/honeycomb at 300 mL/min and $700^{\circ}C$. At this condition, removal amount of $H_2S$ was about 0.337 $g^{H_2S}/g^{sorbent}$. Addition of $K_2CO_3$, $Na_2CO_3$, NaCl and LiCl in the $Li_2ZrO_3$ remarkably improves the $H_2S$ removal capacity of modified $Li_2ZrO_3$/honeycomb up to 23%. Analyses of $Li_2ZrO_3/honeycomb$ sorbent by SEM and XRD showed that $Li_2ZrO_3$ was uniformly impregnated into honeycomb up to considerable amounts. Furthermore, the physicochemical properties of the sorbent did not vary much up to $1000^{\circ}C$.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.2
• /
• pp.59-65
• /
• 2012

Solidification/Stabilization(S/S) is one of the remediation technologies that have been applied for treating inorganic hazardous wastes. This study investigated the reduction of arsenic concentration of arsenic-contaminated soil using by S/S. The binder plays a role in controlling the mobility and solubility of the contaminants in S/S process, so it is important to determine the optimum binder content. Therefore, this study evaluated the effectiveness of S/S using four different binders(cement, zero valent iron, and monosulfate and ettringite(cement-based synthesized materials) at the binder content ranged between 5%(wt.) and 20%(wt.). The leachability of arsenic in 1 N HCl was different depending on the types of binders: cement(71.41%) > monosulfate(47.45%) > ettringite(46.36%) > ZVI(33.08%) at the binder content of 20%. Additionally, three kinds of a mixture binder were prepared using cement and additives(monosulfate, ettringite, calcium sulfoaluminate(CSA)) and tested for arsenic reduction. The highest arsenic removal capacity was found at the mass ratio of cement to the additive, 4:1 in all experiments using a mixture binder, regardless of the additives types. A mixture binder(cement and additives) resulted in higher arsenic removal relative to the arsenic removal when cement was used alone.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.3
• /
• pp.206-213
• /
• 2014

Nutrients such as phosphorus and nitrogen have been widely known as important source of algal appearance in eutrophic water. In order to prevent lake eutrophication, it is required to remove these nutrients not only presented in the lake water, but also released from the sediment. In order to solve this problem this study, the trivalent lanthanum ions and ammonia Nitrogen ($NH_4{^+}-N$) for the adsorption capacity of a zeolite support as it combines the lake water has dissolved in the nutrient removal, as well as deposits in the eluted in the continuously adsorbing the complex to develop and study was to inhibit the growth of algae. In experimental results, lanthanum complexes when the adsorption characteristics were evaluated $PO_4{^{3-}}-P$ and the $NH_4{^+}-N$ removal was confirmed that has an excellent ability, when it applied lake water the time of Chl-a and the turbidity decreased. In this study, these results suggest that the lanthanum complexes produced inhibitory effects on algae in the lake water is determined to excellent. Further, when applied to a complex of lanthanum in lake water to a standard 48 hours Acute Toxicity Method of toxicity were measured, and the results for the toxic effect was not observed.

• Journal of Wetlands Research
• /
• v.17 no.1
• /
• pp.38-44
• /
• 2015

In Korea, most rainfall events occur during summer which then leads to an increasing concern regarding high influx of non-point source pollutants since the pollutant loadings from these non-point sources are very significant. In particular, the first flush of roof-harvested rainfall is said to contain the most highest concentration of nutrients and heavy metals. Accordingly, it is important to develope the possible water quality management options in treating the contaminants and considering reclaimed water reuse. The rain garden could be one of suitable alternatives in addressing this issue. In this study, the development of an effective adsorption media and its application to a lab-scale rain garden was tested to evaluate the removal rate of various nutrient and organic matter (TN, TP, CODcr), and heavy metals (Cu, Cd, Pb). Results showed that carbonized peatmoss produced at higher temperature have better adsorption capacity as compared to the one produced at a lower temperature. When the carbonized peatmoss was applied as rain garden media, the highest removal of TN, TP, and CODcr was observed compared to no carbonized peatmoss applied rain garden. Therefore, this study showed that the carbonized peatmoss would be effectively applied to the rain garden for removing nutrients and heavy metals from roof-harvested rainwater.

• The Journal of Engineering Geology
• /
• v.13 no.1
• /
• pp.29-50
• /
• 2003

Physicochemical Properties of acid mine water of the Chonam-ri Creek and the Sagok-ri Creek in the Kwangyang Au-Ag mine area were determined using geochemical approaches. Metal contamination (Cd, Cu, Pb, Zn) is more serious in the Chonam-ri Creek than in the Sagok-ri Creek. However, the contents of Al and Fe is higher in the Sagok-ri Creek. Such differences between the two creeks probably reflect the abundance and composition of ore minerals. The attenuation processes for acid mine water in both creeks were investigated. In the Chonam-ri Creek, a small retention pond which contains limestone plays an important role in the removal of heavy metals by adsorption or coprecipitation due to increase of pH. The capacity of metal scavenging in this pond depends on the seasonal variation of inflow volume. Reddish yellow precipitates sampled in the Chonam-ri Creek were analyzed by XRD, SEM-EDS, EPMA, and chemical decomposition. The precipitates mainly consist of goethite and are also enriched in Al, Mn, Cu and Zn. This inditates that precipitation of goethite is important for scavenging those trace elements, possibly due to adsorption or coprecipitation. In the Sagok-ri Creek, on the other hand, hydrologic mixing of uncontaminated tributaries results in removal of heavy metals with iron hydroxides precipitation due to the pH increase. The mechanisms proposed for metal attenuation at the confluence between contaminated mine water and uncontaminated tributary water are also explained by the property-property plots.

• Journal of Chest Surgery
• /
• v.8 no.2
• /
• pp.109-118
• /
• 1975

This is a report on four cases of the lobar emphysema due to proximal bronchial obstruction in the Department of Thoracic Surgery, Hanyang University Hospital, during the period of three and half years from 1972 to 1975. First case, a two years old male child was referred to our Department with the lobar emphysema of the lower lobe of the right lung with pneumonia. This emphysema was developed after aspiration of a piece of peanut. Bronchoscopy revealed that the bronchus of the right lower lobe was obstructed with the foreign body, however removal of the peanut through bronchoscope was not attempted because of corruption and softening of the peanut. The removal of the peanut by bronchotomy was performed after subsiding of acute phase of pulmonary infection. Postoperative course was uneventful and the emphysema was disappeared. Second case, a twenty months old female baby was referred to our Department with lobar emphysema of the lower lobe of the left lung. The emphysema was suddenly developed with coughing and dyspneic symptoms and the diagnosis was made roentgenologically. She gave a history of reccurrent infections of the respiratory tract after birth. Bronchoscopy showed an obstruction of the left main bronchus with the growing of fibrinous tissue on the bronchial mucosa. The protruded tissue in the left main bronchus taken out about O.8ml with biopsy forceps for histological examination. After this procedure, the emphysema of the left lung was disappeared. Histological finding was reported to be a chronic inflammatory granulation tissue. Third case, a two and half years old male child was referred to our Department with roentgenological lobar emphysema. Two weeks prior to admission he had an episode of sudden onset of coughing attack with dyspnea. Bronchoscopy revealed that the bronchus of the left lower lobe was obstructed with a mass which was strongly suspected of a neoplastic tissue. At operation, there was found a perforation of enlarged tuberculous lymph node in the bronchus of the left lower lobe and protrusion of granulation tissue into the bronchus. Ruptured orifice on themembranous wall of the left lower lobe bronchus was closed with interrupted suture after the" removal of a perforated tuberculous lymph node. Postoperative course was uneventful and antituberculous chemotherapy was given. Fourth case, a 47 years old man was admitted to our Department with the complaint of severe dyspnea of few months duration. Twenty years ago, he had a history of lung tuberculosis and was treated for many years. X-ray examination including tomography and bronchography revealed that the upper lobe of the right lung was destroyed with cavities, the lower lobe was completely shrunk, and the right middle lobe was strongly overdistended with narrowing bronchial trees. Differential bronchospirometry and lung scanning confirmed that the respiratory function of the affected lung was impaired almost totally. The value of the right lung was calculated on 6% of oxygen uptake, 1% of Minute volume, and 32% of vital capacity. The right pneumonectomy was performed under the careful consideration of anesthetic and surgical procedures. Postoperative course was uneventful and the respiratory function was improved nearly to the normal level.evel.

• Korean Journal of Environmental Agriculture
• /
• v.27 no.3
• /
• pp.231-238
• /
• 2008

This study proposed the method of phosphate recovery from municipal wastewater by using ferrous iron waste, generated from the mechanical process in the steel industry. In the analysis of XRD, ferrous iron waste was composed of $Fe_3O_4$ (magnetite), practically with $Fe^{2+}$ and $Fe^{3+}$. It had inverse spinel structure. In order to identify the adsorption characteristic of phosphate on ferrous iron waste, isotherm adsorption test was designed. Experimental results were well analyzed by Freundlich and Langmuir isotherm theories. Empirical constants of all isotherms applied increased with alkalinity in the samples, ranging from 1.2 to 235 $CaCO_3/L$. In the regeneration test, empirical constants of Langmuir isotherm, i.e., $q_{max}$ (maximum adsorption capacity) and b (energy of adsorption) decreased as the frequency of regeneration was increased. Experiment was further performed to evaluate the performance of the treatment scheme of chemical precipitation by ferrous iron waste followed by biological aerated filter (BAF). The overall removal efficiency in the system increased up to 80% and 90% for total phosphate (TP) and soluble phosphate (SP), respectively, and the corresponding effluent concentrations were detected below 2 mg/L and 1 mg/L for TP and SP, respectively. However, short-circuit problem was still unsolved operational consideration in this system. The practical concept applied in this study will give potential benefits in achieving environmentally sound wastewater treatment as well as environmentally compatible waste disposal in terms of closed substance cycle waste management.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.12
• /
• pp.1287-1292
• /
• 2006

Constructed wetlands are well known as highly efficient system to treat wastewater from different sources. Among the constructed wetlands, upflow types of constructed wetlands have become a common selection of wastewater during the last decade. We conducted a pilot scale study at peen house on treating potential of nutrients by upflow vegetated filter(UVF) pilot wetland which was combined with hydrodynamic separator and used the cattail plant(Typha angustifolia), and operated with artificial nutrients influent. This study evaluate the performances of upflow vegetated fille, in removal of nutrients. The objectives of this study were two-fold: (i) to evaluate the nutrients removal performance of pilot-scale upflow vegetated filter, filled with a mixture of perlite and soil media and planted with cattails and (ii) to design of scale-up upflow vegetated filter using Froude number. Results indicated that, under the condition of the ranges of hydraulic surface load rate were $22.7{\pm}9.6\;m^3/m^2/day$, the average removal of $COD_{Mn}$, and TN, TP were 57.5%, 40.0% and 41.5%, respectively. Computational fluid dynamics, FLUENT 6.0 program was used to predict the distribution of velocity in UVF and hydrodynamic separator. Full scale UVF was designed using the Froude number scale-up method that was assumed geomertic similarity between model and prototype. Result shows that the UVF with 3 m diameter has capacity of design sewage flowrate 75 $m^3/day$.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.8
• /
• pp.603-610
• /
• 2009

This research was performed to improve removal efficiency of toluene and methyl ethyl ketone (MEK) using Candida tropicalis, one of the yeast species. An airlift loop bioreactor (ALB) was employed to enhance the capability of mass transfer for toluene and MEK from the gas phase to the liquid, microbial phase. Polymer gel media made from PAC, alginate and PEG was applied for the effective immobilization of the yeast strain on the polymer gel media. The experimental results indicated that the mass transfer coefficient of toluene without polymer gel media was 1.29 $min^{-1}$ at a gas retention time of 15 sec, whereas the KLa value for toluene was increased to 4.07 $min^{-1}$ by adding the media, confirming the enhanced mass transfer of volatile organic compounds between the gas and liquid phases. The removal efficiency of toluene and MEK by using yeast-immobilized polymer gel media in the ALB was greater than 80% at different pollutant loading rates (5, 10, 19 and 37 g/$m^3$/hr for toluene, 4.5, 8.9, 17.8 and 35.1 g/$m^3$/hr for MEK). In addition, an elimination capacity test conducted by changing inlet loading rates stepwise demonstrated that maximum elimination capacities for toluene and MEK were 70.4 and 56.4 g/$m^3$/hr, respectively.