• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.167-174
• /
• 2001

Reflection method using ultrasonic source has been attempted to obtain the information about tunnel lining structures composed of lining, shotcrete, water barrier and voids at the back of lining. In this work, two different types of sources, i.e. single-pulse source and sweep source, can be used. Single-pulse source with short time duration has the frequency content whose amplitudes tend to be concentrated around the dominant frequency, whereas sweep source with long time duration denotes a flat distribution of relatively larger amplitude over a broad frequency band, although the peak to peak amplitude of single-pulse source wavelet is equivalent to that of sweep source one. In traditional seismic application, a single-pulse source(weight drop, dynamite) is typically used. However, to investigate the fine structure, as it is the case in the tunnel lining structure, the sweep wavelet can be also a desirable source waveform primarily due to the higher energy over a broad frequency band. For the investigation purposes of sweep source, a physical modeling is a useful tool, especially to study problems of wave propagation in the fine layered media. The main purpose of this work was using a physical modeling technique to explore the applicability of sweep source to the delineation of inner layer boundaries. To this end, a two-dimensional physical model analogous to the lining structure was built and a special ultrasonic sweep source was devised. The measurements were carried out in the sweep frequency range 10 ∼ 60 KHz, as peformed in the regular reflection survey(e.g. roll-along technique). The measured data were further rearranged with a proper software (cross-correlation). The resulting seismograms(raw data) showed quitely similar features to those from a single-pulse source, in which high frequency content of reflection events could be considerably emphasized, as expected. The data were further processed by using a regular data processing system "FOCUS" and the results(stack section) were well associated with the known model structure. In this context, it is worthy to note that in view of measuring condition the sweep source would be applied to benefit the penetration of high frequency energy into the media and to enhance the resolution of reflection events.

• Journal of Platform Technology
• /
• v.10 no.3
• /
• pp.60-68
• /
• 2022

As AI-technology develops, interest in the safety of autonomous driving is increasing. Recently, autonomous vehicles have been increasing, but efforts to solve side effects have been sluggish. In particular, night autonomous vehicles have more problems. This is because the probability of accidents is higher in the night driving environment than in the day environment. There are more factors to consider for self-driving at night. Among these factors, reflection of light or reflected light of lighting may be a fundamental cause of night accidents. Therefore, this study proposes method to reduce accidents and improve safety by reducing reflected light generated by the headlights of opposite vehicles or various surrounding light that appear as an important problem in night autonomous vehicles. Therefore, first, in an image obtained by a sensor of a night autonomous vehicle, illumination reflected light is extracted using reflected light characteristic information, and a color of each pixel using a reflection coefficient is found to reduce a special area generated by geometric characteristics. In addition, we find a new area using only the brightness component of the specular area, define it as Illuminated Reflection Light (IRL), and finally present a method to reduce it. Although the illumination reflection light could not be completely reduce, generally satisfactory results could be obtained. Therefore, it is believed that the proposed study can reduce casualties by solving the problems of night autonomous driving and improving safety.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.5 s.335
• /
• pp.9-14
• /
• 2005

Simulation method for a pure radio-frequency (rf) mode of reflection-type and a pure rf mode of transmission-type radio-frequency single-electron transistor (RF-SET) operation is introduced. In this method, the solutions of differential equations based on Kirchhoff's law are obtained self-consistently at frequency-domain. Also, the steady-sate single-electron transistor (SET) current model and the time-dependent SET current model are used in this method. The reflected wave of a typical reflection-type RF-SET and the transmitted wave of a typical transmission-type RF-SET are calculated, and the accuracy of our developed method including the steady-state SET current model is verified with the method introduced by reference 2. At high frequency over GHz, results of our developed method including the time-dependent SET current model are considerably different from that including the steady-state SET current model. At high frequency over GHz, an exact time-dependent SET current model is needed to analyze RF-SET operation.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.3
• /
• pp.191-198
• /
• 2017

To study the behavior of structures subject to blast loads it is important to calculate the loads due to the explosives accurately, especially in the case of interior explosions. It is known that numerical method based on computational fluid dynamics can estimate relatively accurate blast load due to the interior explosion including reflection effect. However, the numerical method has disadvantages that it is difficult to model the analysis and it takes much time to analyze it. Therefore, in this study, the analytical method which can include the reflection effect of the interior explosion was studied. The target structures were set as the slabs of residential buildings subject to interior explosion that could lead to massive casualties and progressive collapses. First, the numerical method is used to investigate the interior explosion effect and the maximum deflection of the slab which was assumed to be elastic, and compared with the analytical method proposed in this study. In the proposed analytical method, we determine the weighting factor of the reflection effect using the beam theory so that the explosion load calculation method becomes more accurate.

• International Journal of Highway Engineering
• /
• v.5 no.3 s.17
• /
• pp.1-9
• /
• 2003

This study was performed to evaluate the effect of various joint sealant on reducing the reflection cracking of asphalt concrete overlay on cement concrete pavement. The test method used was an accelerated reflection cracking test in shear mode, which was developed for evaluation of reflection cracking resistance of overlaid asphalt concrete in laboratory. The test results showed that use of joint sealants resulted in a significant reduction of reflection cracking. When sealant E was used, the fatigue life was the highest, with relatively larger horizontal deformation. When Sealant B was used, the dynamic stability was the highest with the smallest horizontal deformation. In general, the greater the tensile strength of sealant, the better the crack resistance of the mixture.

• Journal of Ocean Engineering and Technology
• /
• v.28 no.3
• /
• pp.227-235
• /
• 2014

Using a 3-D numerical scheme (LES-WASS-3D) that considered wave-structure-sandy seabed interactions in a 3-D wave field, we analyzed the wave reflection and hydraulic characteristics inside a slit caisson with two chambers in a 3-D oblique wave field. To verify the 3-D numerical analysis method suggested in this study, we compared the numerical results with existing experimental results and found good agreement. The numerical analysis revealed that a standing wave field is generated on the front side of the slit caisson due to the effect of wave reflection. For incident waves propagating perpendicular to the slit caisson, the nodes and anti-nodes of the standing wave are apparent and symmetrical. However, in an oblique wave field, as the incident wave angle decreases, the nodes and anti-nodes of the standing wave become ambiguous and unsymmetrical. It was also found that the wave reflection coefficient decreases as the incident wave angle decreases. It can be pointed out that as the incident wave angle decreases, the turbulent intensity in the chamber increases. Thereby, the increased wave energy dissipation by the increased turbulent intensity reduces the rate of wave reflection. In addition, a strong turbulent intensity generally occurs in the first chamber.

• Economic and Environmental Geology
• /
• v.19 no.4
• /
• pp.277-282
• /
• 1986

Accoustic impedances of subsurface layers are determined from the amplitudes of reflections from the layers. Densities of the layers can also be calculated from the accoustic impedances in case where velocities are known by velocity analysis of reflection data or any other method. The accoustic impedance is a good information for direct identification of the kind of some subsurface material like coal or oil.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.5
• /
• pp.211-217
• /
• 2001

Czochralski법에 의한 ZnWO₄단결정을 [100], [101], [001] 방향으로 성공적으로 성장시켰다. 각 축 방향에 따른 성장조건이 rotation speed, pulling rate, 성장된 결정의 직경 등의 변수를 가지고 조사되어졌다. 성장된 결정의 냉각시 발생되는 균열을 annealing 효과에 의하여 방지할 수 있었다. 성장된 결정의 방위는 Laue back reflection으로 결정하였다. 각 축 방향으로 성장된 결정의 미세구조적 특징이 논하여졌으며, 경도, 열팽창계수 및 유전상수의 물리적 특성이 평가되어졌다.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1993.10a
• /
• pp.5-8
• /
• 1993

The purpose of this study is indused to visibility of visual task when a park of visual task covered with veiling reflection by the transparent materials. As a way, we induce the evaluating systems to the visual task by grasping the rolation between the physical factors and visibility.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.129-132
• /
• 1998

In this paper, we have studied the effect of electron reflection on shadow mask on which tungsten oxide film is coated and have studied the variation of beam mislanding with coating thickness in CRT. We found the method to be able to control coating thicknessed and optimum coating thickness of tungsten oxide film was 1∼2$\mu\textrm{m}$. Mislanding of electron beam was reduced about 20∼48% with increasing coating thickness in CRT