• International Journal of Aeronautical and Space Sciences
• /
• v.12 no.2
• /
• pp.175-178
• /
• 2011

An optical fiber-based beam width measurement technique is presented. The proposed system can be applied to the optical fiber industry in applications such as lensed fiber, optical fiber based laser beam source, and fiber optic sensor. The measurement system is composed of optical fiber, which is used as a transceiver, and a single grating panel which consists of a multi-reflection area with an even non-reflection area. The grating panel is used to vary the reflected light. When the widths of the reflection area and non-reflection area are larger than the optical beam width, the reflected light is varied at the interface between the reflection area and the non-reflection area by the movement of the grating panel. Experiments were conducted in order to verify the feasibility of the proposed technique. Multi-mode fiber combined with a collimator was selected as an emitter and a receiver, and the beam width measurement system was contrived. Subsequently, the proposed method and the system were verified by comparing the experimental results with the results of the conventional charge-coupled device technique.

• Nuclear Engineering and Technology
• /
• v.52 no.4
• /
• pp.856-862
• /
• 2020

Defect inspection system for industrial applications takes the important portion. Non-destructive inspection method has been significantly improved. Infrared thermography, as one of method for non-destructive inspection, can provide relatively precise data and quick inspection time. This study, it was performed to measure defect according to the measurement limit of the non-visible areas such as the back surface of the pipe using reflection plate using reflection plate based on Infrared thermography. The materials of the reflection plate were determined in consideration of the space limitation and the thermal characteristics, and defects were detected by the manufactured reflection plate. Detection of defect in non-visible area using the candidate materials for reflection plate was conducted.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.303-309
• /
• 2000

Seismic reflection method is applied to detect shallow location of limestone in Chechon area. The data using hammer source is compared with that of weight drop. Small size hammer and weight-drop are used as energy source and 100Hz geophones are used for data aquisition. Data processing is conducted utilizing the available processing technique of "Geobit", which is seismic data processing software developed by KIGAM. The result of above data processing, the velocity of topsoil layer is 1,250m/sec. The velocity of this area is higher than other area because loading trucks pass this area and make this layer compact. And in limestone area, hammer is proposed to energy source instead of weight drop because the energy propagates the layer very well.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.5
• /
• pp.852-857
• /
• 2006

This paper presents a precision method to calculate the electric field density of mountain area using digital terrain elevation data(DTED). Generally we calculate the electric field density of a point adding a direct field density and horizontal reflection field density between two points. In this paper, we consider a vertical reflection field density from vertical surface near the wave propagation line between transmitter and receiver. The vertical reflection electric field have different propagation path and polarization from a horizontal reflection field. And the total electric field density adding horizontal field density and vertical reflection value is more accurate than a direct path electrical field density or direct field density adding a horizontal reflection field density.

• 대한공업교육학회지
• /
• v.39 no.2
• /
• pp.1-18
• /
• 2014

This study took existing invention intellectual property related textbooks being utilized in secondary vocational education, analyzed the formation status of 'key learning elements' reflection ratio and drew optimum key learning elements formation ratio by invention intellectual property education content required in secondary vocational education in the future. For this, the study task was set up as 'what kind and how much of invention intellectual property key learning elements are in the invention intellectual property textbook education content now and what is the desirable ratio of each key learning elements in the future'. To resolve this task, 3 specialists analyzed the invention intellectual property education content reflection status and optimum reflection ratio by invention intellectual property education content required in the future is suggested by Delphi survey. The results of this study are as following. First, the result of analysis on invention intellectual property key learning elements included in the invention patent recognition books being utilized in secondary vocational education was that the books included all key learning elements; however, some textbooks have the trend of concentrating in D area (problem-solving activities). Second, the result of analysis on the reflection ratio by invention intellectual property education content area in the invention patent recognition books being utilized in secondary vocational education was that there was the trend in most textbooks that they concentrate in intellectual property creation area; while some textbooks deal with intellectual property protection area and intellectual property utilization area. Regarding by achievement type, knowledge area was main in all textbooks. Meanwhile, function area is dealt in invention patent basic, invention and problem-solving and design textbooks. Attitude area is not dealt or is dealt insufficiently in most textbooks. Third, the optimum reflection ratio of invention intellectual property education key learning elements required in secondary vocational education in the future as obtained by specialists' delphi survey was that it is necessary to decrease D (problem-solving activities) 17.7% area, E(invention fusion knowledge) 2.9% area, K(patent application) 6.9% and L(patent information investigation) area 9.6%. Regarding the optimum reflection ratio of invention intellectual property education content, it is suggested that the invention literacy area 3.1%, intellectual property creation area 4.5% and intellectual property protection area 10.6% would be decreased; while intellectual property utilization area 17.7% would be increased. Regarding optimum reflection ratio of achievement type, it is suggested that knowledge area 52% would be decreased; while function area 32.3% and attitude area 19.6% would be increased.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.09a
• /
• pp.35-38
• /
• 2000

Reflection cracks can be occurred in the asphalt layer overlaid on portland cement concrete pavements, because this layer is sensitive to environmental conditions including temperature changes and displacements of the pavement. A result of trial applications using glass fiber grids is introduced in this paper. Glass fiber grids were used between the asphalt layer and the concrete base to reduce the reflection crack of the asphalt layer. No cracks were observed in the glass grid installed area about 2 years later from trial constructions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.6
• /
• pp.471-476
• /
• 2010

This paper has studied dissymmetrical light distribution design using the secondary optics in the simulation. fundamental Lambertian radiation distribution based on LED has been cut off by the secondary optics, and the first surface slope of lens and second surface slope of total reflection area have been calculated through formula. PMMA (the index of refraction: 1.49361) which is material of lens has been selected. critical angle($42.02993^{\circ}$) between Air and PMMA has been calulated by snell's law, and total reflection angle slope has been selected about $16.67^{\circ}$ to occur the total reflection. when the first surface slope and the second surface slope has been set up, Rays of all total reflection area have generated the total reflection. finally, designed LED Module has been estimated by Korean Industrial Standards for LED safety street lighting. dissymmetrical light distribution have been analyzed with reached effect of road illuminance, and average road illuminance which are each 70.6 lx, 40.35 lx, and 25.88 lx have been satisfied with Korean Industrial Standards for LED safety street lighting.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.807-814
• /
• 2004

Land seismic reflection survey has been increasingly demanded in various civil engineering works because of its own ability to delineate layers, water table, to detect cavities or fracture zones, to estimate seismic velocities of each layer. However, our shallow subsurface structures are very complex. The relatively thin layer(mostly soil) to the wavelength directly followed by a basic rock with high impedance used to generate complicated surface waves, kind of channel waves with high amplitude that is dominate in entire seismograms and hence the useful reflection events will be almost hopelessly immersed in the undesired surface waves. Thus, it would seem that the use of traditional seismic survey could not be likely to provide in itself a satisfactory information about our exploration targets. This paper hence introduces an efficient measuring strategy illustrating a properly controlled arrangement of the vertical single force sources commonly used, yielding a very sharply elongated form of P-energy with a minimum of S radiation energy, what we call, P-beam source. Abundant experiments of physical modeling showed that in that way the surface waves could be enormously reduced and the reflection events would be additive and thus reinforced. Examples of field data are also illustrated. The contribution of P-beam source will be great in civil engineering area as well as in general geological exploration area.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2009.01a
• /
• pp.644-648
• /
• 2009

Accurate rendering of a virtual scene in real time has been one of important issues for virtual reality (VR) technology. Specular reflection of light has been studied a long time, which is always seen on a metallic object and causes occasionally very strong brightness (highlight). Due to restriction of number of gradation of brightness (usually 256), maximum brightness and contrast ratio, the highlight is relatively weakly represented by displays and projectors. In addition, specular reflection will be take influence of binocular parallax and motion parallax, because it is light to reflect in a specific course. Therefore in this paper, an emphasized highlight model of a metallic object on the CAVE system is proposed. Decreasing brightness slightly on neighbor area of highlighted area, the proposed method increases contrast ratio between the highlighted area and neighbor area. Furthermore, using features of CAVE, the proposed method also represents glance (blink). When a metallic object moves, the method alternatively represents images with highlight and without highlight for both eyes. Since the difference of images for both eyes influences binocular parallax and motion parallax, a userfeels glance more realistically.

• Journal of Platform Technology
• /
• v.10 no.3
• /
• pp.60-68
• /
• 2022

As AI-technology develops, interest in the safety of autonomous driving is increasing. Recently, autonomous vehicles have been increasing, but efforts to solve side effects have been sluggish. In particular, night autonomous vehicles have more problems. This is because the probability of accidents is higher in the night driving environment than in the day environment. There are more factors to consider for self-driving at night. Among these factors, reflection of light or reflected light of lighting may be a fundamental cause of night accidents. Therefore, this study proposes method to reduce accidents and improve safety by reducing reflected light generated by the headlights of opposite vehicles or various surrounding light that appear as an important problem in night autonomous vehicles. Therefore, first, in an image obtained by a sensor of a night autonomous vehicle, illumination reflected light is extracted using reflected light characteristic information, and a color of each pixel using a reflection coefficient is found to reduce a special area generated by geometric characteristics. In addition, we find a new area using only the brightness component of the specular area, define it as Illuminated Reflection Light (IRL), and finally present a method to reduce it. Although the illumination reflection light could not be completely reduce, generally satisfactory results could be obtained. Therefore, it is believed that the proposed study can reduce casualties by solving the problems of night autonomous driving and improving safety.