• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.827-831
• /
• 2008

In this paper, kinematic analysis for a planar 3-DOF redundant stage which has four actuators is presented by using SimMechanics software package. SimMechanics is a block sets of the Matlab/Simulink package. The SimMechanics enables a simplified model for a complex kinematic mechanism, since kinematic relationship between joints and linkages for the kinematic chains are expressed as line vectors and block diagrams. Here, positional error and limit values of movement ranges of the stage are evaluated by using the SimMechanics. The validity of the kinematic characteristics model was compared with theoretical kinematic analyses for the 3-DOF stage.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.605-610
• /
• 1994

This paper discusses the solution to the precise positioning control problem applied to a simple model of a dual stage or redundant positioner. The dual stage actuator presented here uses a VCM(Voice Coil Motor) as a coarse actuator and a piezoelectric actuator as a fine actuator. By adopting controllers with two-degree-of-freedom and by optimizing H$_{2}$ faster precise tracking can be realized. Experimental and numerical results are presented to demonstrate the control effects.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10a
• /
• pp.69-72
• /
• 1996

This paper considers a global resolution of kinematic redundancy under inequality constraints as a constrained optimal control. In this formulation, joint limits and obstacles are regarded as state variable inequality constraints, and joint velocity limits as control variable inequality constraints. Necessary and sufficient conditions are derived by using Pontryagin's minimum principle and penalty function method. These conditions leads to a two-point boundary-value problem (TPBVP) with natural, periodic and inequality boundary conditions. In order to solve the TPBVP and to find a global minimum, a numerical algorithm, named two-stage algorithm, is presented. Given initial joint pose, the first stage finds the optimal joint trajectory and its corresponding minimum performance cost. The second stage searches for the optimal initial joint pose with globally minimum cost in the self-motion manifold. The effectiveness of the proposed algorithm is demonstrated through a simulation with a 3-dof planar redundant manipulator.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2594-2599
• /
• 2003

We consider some problems of the Modified SPRT(Sequential Probability Ratio Test) method for fault detection and isolation of inertial redundant sensor systems and propose an Advanced SPRT method to solve the problems of the Modified SPRT method. One problem of the Modified SPRT method to apply to inertial sensor system comes from the effect of inertial sensor errors such as misalignment, scale factor error and sensor bias in the parity vector, which make the Modified SPRT method hard to be applicable. The other problem is due to the correlation of parity vector components which may induce false alarm. We use a two-stage Kalman filter to remove effects of the inertial sensor errors and propose the modified parity vector and the controlled parity vector which removes the effect of correlation of parity vector components. The Advanced SPRT method is derived form the modified parity vector and the controlled parity vector. Some simulation results are presented to show the usefulness of the Advanced SPRT method to redundant inertial sensor systems.

• Structural Engineering and Mechanics
• /
• v.63 no.6
• /
• pp.799-808
• /
• 2017

Failure of a redundant long-span bridge is often described by innumerable failure modes, which make the structural system reliability analysis become a computationally intractable work. In this paper, an innovative procedure is proposed to efficiently identify the dominant failure modes and quantify the structural reliability for a long-span bridge system. The procedure is programmed by ANSYS and MATLAB. Considering the correlation between failure paths, a new branch and bound operation criteria is applied to the traditional stage critical strength branch and bound algorithm. Computational effort can be saved by ignoring the redundant failure paths as early as possible. The reliability of dominant failure mode is computed by FORM, since the limit state function of failure mode can be expressed by the final stage critical strength. PNET method and FORM for system are suggested to be the suitable calculation method for the bridge system reliability. By applying the procedure to a CFST arch bridge, the proposed method is demonstrated suitable to the system reliability analysis for long-span bridge structure.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.12
• /
• pp.60-69
• /
• 2000

This paper describes a single-chip full-custom implementation of pipelined adaptive decision-feedback equalizer(PADFE) using a 0.25-${\mu}m$ CMOS technology for wide-band wireless digital communication systems. To enhance the throughput rate of ADFE, two pipeline stages are inserted into the critical path of the ADFE by using delayed least-mean-square(DLMS) algorithm. Redundant binary (RB) arithmetic is applied to all the data processing of the PADFE including filter taps and coefficient update blocks. When compared with conventional methods based on two's complement arithmetic, the proposed approach reduces arithmetic complexity, as well as results in a very simple complex-valued filter structure, thus suitable for VLSI implementation. The design parameters including pipeline stage, filter tap, coefficient and internal bit-width, and equalization performance such as bit error rate (BER) and convergence speed are analyzed by algorithm-level simulation using COSSAP. The single-chip PADFE contains about 205,000 transistors on an area of about $1.96\times1.35-mm^2$. Simulation results show that it can safely operate with 200-MHz clock frequency at 2.5-V supply, and its estimated power dissipation is about 890-mW. Test results show that the fabricated chip works functionally well.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1281-1284
• /
• 1997

In this article, the configuration of weight lifer is analyzed using manipulibility polytope. After modeling body as 7-link redundant robot, optimal joint angles during first stage are searched by dynamic programmi technique and compared with standard reference data.

• Structural Engineering and Mechanics
• /
• v.52 no.5
• /
• pp.919-935
• /
• 2014

In this study, the control of the shape of pre-stressed cable structures and the effective control element were examined. The process of deriving the displacement control equations using the force method was explained, and the concurrent control scheme (CCS) and the sequence control scheme (SCS) were proposed. To explain the control scheme process, the quadrilateral cable net model was adopted and classified into a regular model and an irregular model for the analysis of the control results. In the control analysis of the regular model, the CCS and SCS analysis results proved reliable. For the SCS, the errors occur in the control stage and varied according to the control sequence. In the control analysis of the irregular model, the CCS analysis result also proved relatively reliable, and the SCS analysis result with the correction of errors in each stage was found nearly consistent with the target shape after the control. Finally, to investigate an effective control element, the Geiger cable dome was adopted. A set of non-redundant elements was evaluated in the reduced row echelon form of a coefficient matrix of control equations. Important elements for shape control were also evaluated using overlapping elements in the element sets, which were selected based on cable adjustments.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.29B no.9
• /
• pp.68-75
• /
• 1992

In this paper the back-propagation algorithm through omitting redundant learning has been proposed to improve learning speed. The proposed algorithm has been applied to XOR, Parity check and pattern recognition of hand-written numbers. The decrease of the number of patterns to be learned has been confirmed as learning proceeds even in early learning stage. The learning speed in pattern recognition of hand-written numbers is improved more than 2 times in various cases of hidden neuron numbers. It is observed that the improvement of learning speed becomes better as the number of patterns and the number of hidden numbers increase. The recognition rate of the proposed algorithm is nearly the same as that conventional method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.6
• /
• pp.1169-1181
• /
• 1994

The Gamma Network contains the redundant path thereby is provides the ability to tolerate the faults occured. However, in case of identical the source and destination number, only a single path exists, therefore there is no way of connecting for the fault situation. In addition, for the dynamic packet routing strategy, it shoed perform backtracking analysis to find the redundant path. In this paper we proposed a new network, Dual Network, to resolve these drawbacks. The Dual Network uses switching elements about the same network size as the Gamma Network except first and last stage, and it is more efficient than the Gamma Network, for it has reduced the switching stage by one. And since is used a destination tag routing scheme for the control algorithm, it has on advantage of becoming of simpler and faster routing control.