• Journal of the Korean Institute of Telematics and Electronics A
• /
• 제33A권4호
• /
• pp.11-17
• /
• 1996

In the case of redundancy control performed by a netowrk management system, it can not be ignored some delay of control time and break of control by failure of the system. This paper proposed a new method to improve the performacne of a redundancy control system interfaced to the network management system. At first, it produced the modelling of the total system and analyzed the functional relation of reliability and failure rate for a transmission system having an one-to-one active redundancy structure controlled by itself. After describing the loss rate of transmission data and the time required for the redundancy control process of the network management system when a failure is occurred, it proposed the new redundancy method of complex system control mode as an effective redundancy control method to improve reliability of a redundancy control system. Finally, it proved the effect by comparing the new result to the previous result.

• Journal of IKEEE
• /
• 제21권2호
• /
• pp.130-135
• /
• 2017

Normally, in data transmission, extra parity bits are added to the input message which were derived from its input and a pre-defined algorithm. The same algorithm is used by the receiver to check the consistency of the delivered information, to determine if it is corrupted or not. It recovers and compares the received information, to provide matching and correcting the corrupted transmitted bits if there is any. This paper aims the following objectives: to use an alternative error detection-correction method, to lessens both the fixed number of the required redundancy bits 'r' in cyclic redundancy checking (CRC) because of the required polynomial generator and the overhead of interspersing the r in Hamming code. The experimental results were synthesized using Xilinx Virtex-5 FPGA and showed a significant increase in both the transmission rate and detection of random errors. Moreover, this proposal can be a better option for detecting and correcting errors.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• 제23권10호
• /
• pp.75-80
• /
• 2009

In order to prevent loss of communication packets and drop of transmission speed owing to the network fault occurrence, it should be considered network redundancy. That is why a messages of IED GOOSE is the critical signal in charge of protection and control of the substation. So most of users implement the substation automation system with Hybrid network topology ant IED supporting double ethernet ports. Because IEC 61850 GOOSE conformance test is limited in the functional test, this paper suggests how to test the performance of IED GOOSE transmission considering Network redundancy, and describes the analysis of an example test on real IEDs and how to impact the IED GOOSE performance to the substation automation system.

• KIPS Transactions on Computer and Communication Systems
• /
• 제4권9호
• /
• pp.321-326
• /
• 2015

In this paper, we proposed an algorithm which could transmit reliable data between smart devices by using inaudible high frequency of audible frequency range and cyclic redundancy check method. The proposed method uses 18 kHz~22 kHz as high frequency which inner speaker of smart device can make a sound in audible frequency range (20 Hz~22 kHz). To increase transmission quantity of data, we send mixed various frequencies at high frequency range 1 (18.0 kHz~21.2 kHz). At the same time, to increase accuracy of transmission data, we send some mixed frequencies at high frequency range 2 (21.2 kHz~22.0 kHz) as checksum. We did experiments about data transmission between smart devices by using the proposed method to confirm data transmission speed and accuracy of the proposed method. From the experiments, we showed that the proposed method could transmit 32 bits data in 235 ms, the transmission success rate was 99.47%, and error detection by using cyclic redundancy check was 0.53%. Therefore, the proposed method will be a useful for wireless transmission technology between smart devices.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• 제63권12호
• /
• pp.1640-1648
• /
• 2014

This paper proposes a switching frequency reduction method for MMC (Modular Multilevel Converter) utilizing redundancy operation of sub-module, which can offer reduction of voltage harmonics and switching loss. The feasibility of proposed method was verified through computer simulations with PSCAD/EMTDC software. Based on simulation analysis, a hardware scaled-model of 10kVA, DC-1000V MMC was designed and manufactured in the lab. Various experiments were conducted to verify the feasibility of proposed method in the actual hardware system. The hardware scaled-model can be effectively utilized for analyzing the performance of MMC according to the modulation scheme and redundancy operation.

• Journal of Communications and Networks
• /
• 제11권6호
• /
• pp.564-573
• /
• 2009

In this paper, we consider a wireless multiple path network in which a transmitting node would like to send a message to the receiving node with a certain probability of success. These two nodes are separated by N erasure paths, and we devise two algorithms to determine minimum redundancy and optimal symbol allocation for this setup. We discuss the case with N = 3 and then extend the case to an arbitrary number of paths. One of the algorithms minimum redundancy algorithm in exponential time is shown to be optimal in several cases, but has exponential running time. The other algorithm, minimum redundancy algorithm in polynomial time, is sub-optimal but has polynomial worstcase running time. These algorithms are based off the theory of maximum-distance separable codes. We apply the MRAET algorithm on maximum-distance separable, Luby transform, and Raptor codes and compare their performance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• 제25권7호
• /
• pp.930-939
• /
• 2021

In recent years, the use of broadband bandwidth and redundant links for stable transmission in networks has resulted in excessive energy consumption and reduced transmission efficiency. In this paper, we propose an optimization algorithm that reduces the number of transmission links and minimizes transmission energy by removing redundant traffic in networks where traffic redundancy is allowed. The optimization algorithm proposed in this paper uses the meta-heuristic method using Tabu search algorithm. The proposed optimization algorithm minimizes transmission energy by designing a neighborhood generation method that efficiently routes overlapping traffic. The performance evaluation of the proposed optimization algorithm was performed in terms of the number of links used to transmit all traffic generated in the network and the transmission energy consumed. From the performance evaluation results, it was confirmed that the proposed algorithm is superior to other algorithms previously proposed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제12권4호
• /
• pp.347-356
• /
• 1987

This paper is to propose a new line code suitable for a high speed unipolar pulse transmission system, such as a high speed optical digital transmission system. The original information speed can be converted into the transmission speed $\frac{(m+1)}{m}$ by the speed converter. Then this code, named mBiZ code, is generated by means of an Exclusive NOR between the bit stream inserted a space into every m bits and the bit stream delayed by the time slot allocated a single bit at the output coded sequence. Therefore, a mBiZ code can reduce a redundancy in the line code for transmission and its conversion circuits can be devised easily. The mBiZ code can also suppress undesirable long consecuitive identical digits and make line code balance in the mark and space ratio. Therefore, high frequency and low frequency components in power spectrum of a mBiZ code can be suppessed.

• Journal of Electrical Engineering and Technology
• /
• 제10권2호
• /
• pp.474-486
• /
• 2015

This paper proposes a multi-objective optimal placement method of Phasor Measurement Units (PMUs) in large electric transmission systems. It is proposed for minimizing the number of PMUs for complete system observability and maximizing measurement redundancy of the buses, simultaneously. The measurement redundancy of the bus indicates that number of times a bus is able to monitor more than once by PMUs set. A high level of measurement redundancy can maximize the system observability and it is required for a reliable power system state estimation. Therefore, simultaneous optimizations of the two conflicting objectives are performed using a binary coded firefly algorithm. The complete observability of the power system is first prepared and then, single line loss contingency condition is added to the main model. The practical measurement limitation of PMUs is also considered. The efficiency of the proposed method is validated on IEEE 14, 30, 57 and 118 bus test systems and a real and large- scale Polish 2383 bus system. The valuable approach of firefly algorithm is demonstrated in finding the optimal number of PMUs and their locations by comparing its performance with earlier works.

• Proceedings of the IEEK Conference
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 Ⅳ
• /
• pp.1920-1923
• /
• 2003

This paper presents compression rate improvement for SPIHT algorithm though redundancy bit removing. Proposed SPIHT algorithm uses a method to select of optimized threshold from feature of wavelet transform coefficients and removes sign bit if coefficient of LL area. Experimental results show that the proposed algorithm achieves more improvement bit rate and more fast progressive transmission with low bit rate.