• Journal of Korean Institute of Industrial Engineers
• /
• v.36 no.1
• /
• pp.69-77
• /
• 2010

The failure rate model of External Environment Maintenance(EEM) for a system under severe environment is investigated. EEM, which is recently introduced concept, is a maintenance activity controlling external environment factors that potentially cause system failure such as cleaning equipment, controlling temperature (humidity) and removing dust inside of electronic appliances. EEM can not have any influence on the inherent failure rate of a system but reduce the severity of the external environment causing failure since it deals with only external environment factors. Therefore, we propose two failure rate models to express the improvement effect of EEM: The intensity reduction model and age reduction model. The intensity and age reduction models of EEM are developed assuming the quality of improvement effect is proportioned to an extra intensity or age respectively. The validation of proposed failure rate models is performed in order of data generation, parameter estimation and test for goodness-of-fit.

• Journal of Korean Society for Atmospheric Environment
• /
• v.26 no.3
• /
• pp.245-252
• /
• 2010

For the purpose of evaluating to remove elemental mercury using SCR (Selective Catalytic Reduction) catalysts, the result of the concentration variation of elemental mercury in lab experiment and field measurement was compared. The effect of the elemental mercury oxidation on commercial catalysts was studied in simulated gas. Three species of SCR catalyst, $V_2O_5-TiO_2$ type, were selected. The elemental mercury reduced 30% without HCl gas in SCR operating condition. But the width of reduction increased 60% at 20 ppm HCl gas. According to the result of field measurement, reduction rate of elemental mercury at SCR outlet showed 60%. The total mercury concentration decreased about 20%. The results were similar to the lab test. The results of chemical analysis of test sample showed increase of mercury concentration but surface change was not observed.

• Journal of Korea Society of Industrial Information Systems
• /
• v.23 no.3
• /
• pp.131-142
• /
• 2018

Since income growth rate and poverty level are related, there is a possibility that the poverty rate may converge in the long run steady state as well. If the poverty rate converges, then for this study the state that begins with the high poverty rate would have a higher poverty reduction rate. To examine the convergence of poverty rate among the US states, this study uses two times series methodologies. First, in order to prevent the power loss from ignoring the structural break when testing for a unit root in a single time series, this study employs the newly developed panel LM unit root tests with level and trend shifts. The results of unit root tests of the log of poverty rate without allowing for structural breaks show that twenty six states reject the null hypothesis of unit root test for the ADF test, twenty five states for the LM test, and thirty five states for the RALS-LM test. The result of unit root tests that allow one structural break shows that the null hypothesis of a unit root test is rejected for twenty two states with the LM test, and thirty three states with the RALS-LM test. This supports poverty rates are converging among US states.

• The Journal of Asian Finance, Economics and Business
• /
• v.7 no.7
• /
• pp.229-239
• /
• 2020

This article aims to measure the impact of economic growth and urbanization on poverty reduction in Vietnam, and verify whether economic growth and urbanization will help reduce poverty rates. Data for this study are tabular data related to growth, urbanization and poverty at the provincial level for the period of nine years, from 2006 to 2014 provided by the Vietnam General Statistics Office and the Vietnam General Department of Customs. The level of economic growth and urbanization mentioned in the study is reflected in such indicators as GDP value, exports value, imports value, urbanization rate and employment rate. The authors used logistic regression models with fixed-effects and logistic regression models with random effects. With 5% confidence level tested by the Chi-Square test of Hausman trial with the fixed-effect model, research results show that: (1) factors with significant negative impact on the poverty rate include imports value, urbanization rate and, employment rate; (2) factors that do not affect the poverty rate include exports value and GDP value. Based on the research results, this study proposes a number of policy recommendations to help promote economic growth, to sustain the urbanization process, and to contribute directly and positively to poverty reduction in Vietnam.

• Journal of Environmental Science International
• /
• v.32 no.1
• /
• pp.1-9
• /
• 2023

In this study, a horticultural therapy program was performed by employing the anger experienced by people during daily life activities in the emotion regulation strategy-based program to identify the influence of the horticultural program on anger control in the caregivers for patients with dementia. To measure this influence, two tools were used: a self-administered questionnaire survey, which is a subjective test, and an instrumental test, which can measure the physical index that detects the physical changes through anger. For the preliminary test, depression, stress, self-esteem, anxiety, and anger state-characteristic were tested using the self-administered questionnaire. For the follow-up test, the self-administered survey and the test using the physical index were performed in a manner similar to that of the preliminary test. The self-administered questionnaire comprised questions suitable to this study and considered the age, education level, and economic aspect of the subjects. The test results indicated that the experimental group subjected to the emotion regulation strategy-based horticultural therapy showed very significant reduction in depression and anger and significant reduction in stress, self-esteem, and anxiety. In the physical index test, the systolic and diastolic blood pressures were reduced, and the pulse rate and respiration rate reduced before and after the therapy, thus, proving the effectiveness of the therapy in anger control.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.11 s.176
• /
• pp.45-50
• /
• 2005

In this study, the casting/forging process was applied in manufacturing a low control arm, in order to prove that application of casting/forging process to Al6061 is likely to get the effect of light weight compared with existing steel products and to reduce the cost of materials. Firstly, In order to set up the optimum casting condition of the forging material, Al6061, casting experiments were carried out by controlling pouring temperature of the aluminum for casting, mold temperature, and pouring time. $700^{\circ}C$ pouring temperature, $300^{\circ}C$ mold temperature and 10-second pouring time were taken into account as the optimum casting conditions. With respect to a hot forging test, it is practiced on the basis of a temperature of materials, strain rate, and reduction rate so as to observe each microstructure and examine strain-stress curve simultaneously; examine tensile test and hardness test; eventually set up the optimum hot forging condition. A hot forging test, tensile test, hardness experiment, and microstructure observation were carried out on condition of $70\%$ reduction rate, $500^{\circ}C$ temperature of materials, and 1 strain rate. As a result of those experiments, 330MPa tensile strength, $16.4\%$ elongation, and 122.8Hv hardness were recorded. In oder to get a sound preform which has no unfitting cavity and less flash, two preforms were proposed on the basis of volume rate of the final product; the optimum volume rate of preform for the low control arm was $115\%$. In conclusion, it is confirmed that using the forging material rather than casting materials in casting/forging process is likely to get more superior mechanical properties. Compared with Al6061, performed by means of general forging, moreover, cast/forged Al6061 can not only stimulate productivity by reducing production processes, but cut down the cost of materials by reusing forging scraps.

• Journal of ILASS-Korea
• /
• v.29 no.2
• /
• pp.68-74
• /
• 2024

As awareness of environmental pollution problems increases worldwide, interest in air pollutants is increasing. In particular, NOx and PM, which are major pollutants in diesel vehicles, are contributing significantly to emissions. As a result, its importance is increasing. In this study, based on research results applied to large diesel vehicles, the problem of natural regeneration caused by low exhaust gas temperature during low speed and low load operation is solved by applying a complex regeneration DPF that is not affected by temperature conditions to small diesel vehicles. The feasibility of application to small diesel vehicles was reviewed by measuring the emission reduction efficiency. As a result of the engine test, the power reduction rate and fuel consumption rate before and after device installation under full load conditions were 2.9% decrease and 3.5% increase, respectively, satisfying the standard for a 5% reduction, and as a result of the regeneration equilibrium temperature (BPT) test, the regeneration temperature was 310℃. appeared at the level. The reduction efficiency test results for the actual vehicle durability test equipment showed 97.3% PM, 51.0% CO, and 31.1% HC, while the city commuter vehicle had PM 97.5%, CO 61.7%, HC 40.0%, and the school bus vehicle had PM 96.8%, CO 44.4%, HC 34.3%, and low-speed logistics vehicles showed a reduction efficiency of 98.2% for PM, 36.0% for CO, and 45.7% for HC. Based on the results of this study, in the future, it is necessary to secure DPF technology suitable for all vehicle types through actual vehicle application research on temperature condition-insensitive composite regenerative DPF for medium-sized vehicles.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.24 no.3
• /
• pp.63-71
• /
• 2022

This paper aims to compare and verify the antibacterial effects of cotton fabrics naturally dyed with extracts of Ulmus davidiana var. japonica Nakai, Caesalpinia sappan, Saururus chinensis, and Artemisia princeps against antibiotic-resistant strains of bacteria. After natural dyeing of the test fabric, Al, Cu, Fe mordants were used. The color fastness against washing, rubbing, and perspiration of the cotton fabrics dyed with the 4 types of extracts were mostly excellent. However, the color fastness against light showed poor results for all four types. As for the antibacterial test method, MRSA (ATCC 33591) was applied to the cotton fabrics dyed with the four kinds of extracts and cultured for 24 hours. After that, the bacteria that proliferated on the fabrics were collected and spread on a solid medium. The bacteria were measured to find out the bacteriostatic reduction rate for the antibiotic-resistant strains. As a result of the analysis, all four extracts showed a high bacteriostatic reduction rate of more than 99% when the copper mordant was used. Even with the lack of a mordant, the bacteriostatic reduction rate was high, at 99.9% for Caesalpinia sappan and 94.6% for Saururus chinensis.

• Korean Journal of Agricultural Science
• /
• v.37 no.3
• /
• pp.491-499
• /
• 2010

This study was carried out to investigate the consolidation characteristics of the remolded clay by the oedometer and the constant rate of strain(CRS) consolidation tests. As the rate of strain increases, the settlement rapidly decreased. As the ratio of the sand in the specimen increases, its effect on the rate of strain to the settlement was reduced. As the effective stress increased, the void ratio decreased, while the rate of strain increased, it did not show a clear variation. The reduction of the void ratio was shown to be less than the oedometer test. The coefficient of vertical consolidation with effective stress showed very large variation around preconsolidation stress, but the rate of strain did not provide significant effects. The rate of strain with effective stress gradually decreased at all tests and mixed ratio of sand. The rate of strain at the constant rate of strain tests showed smaller than in the oedometer test. The coefficient of consolidation at the constant rate of strain tests showed much more increase than in the oedometer test. The ratio of the vertical coefficient of consolidation by the odometer and the constant rate of strain tests showed a large difference according to various tests method and mixing ratio. Therefore, it is recommended that careful attention should be paid to designing the soft ground improvement.

• Journal of Environmental Health Sciences
• /
• v.33 no.1 s.94
• /
• pp.36-42
• /
• 2007

Diesel PM can be controlled using Diesel Particulate Filter, which can effectively reduce the level of soot emissions to ambient background levels. In the Heavy Duty Diesel area, the Continuously Regeneration trap has been widely applied in the retrofit market. As the Special act for the improvement of air quality in the capital area, the retrofit program for DPF to used diesel vehicle has progressed favorably and there are currently over 1,000 of these DPF in use in retrofit applications in korea. These DPF comprise a specially formulated Diesel Oxidation Catalyst upstream of a DPF. The $NO_2$ generated by the DOC is used to combust the carbon collected in the DPF at low temperature. To certificate DPF device that is suitable to domestic circumstances, it is necessary to evaluate exactly the DPF devices according to the regulation of DPF certificate test procedure for retrofit(ministry of environment(MOE) announcement NO. 2005-16). To do so the understand of that regulation like the standard of PM reduction rate is needed. In this study the test procedure including test cycle and BPT test condition was examined and also the test result for specific DPF was analyzed. In every test like field test, PM reduction efficiency test and seoul-10 mode test, no defect could be showed.