• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.382-385
• /
• 2003

Introduction of digital broadcasting service does not only mean the change of information transmission method but also the change of total broadcasting system. In past day, Television was only received one-sided information from broadcasting station, but digital broadcasting means that digital television becomes the most important means of information transmission by the introduction of new programming, lots of channels, data service, multi communication. In the age of the digital broadcasting, the recording and replay medium's interest is getting higher. The medium is able to record more than 24 hours' digital broadcasting programs without additional tapes. In this paper the recording and replay device using HDD was implemented and device driver based on linux was programmed. It has Intel PXA250 processor and hard disk is used as storage equipment. And transport Stream is saved on hard disk through PXA250's data bus. FIFO is added to solve the different saving speed and FPGA is also added to display the saved data.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.309-312
• /
• 1997

The Ce-Cr(-Ta) film are one of the most suitable candidates for perpendicular magnetic media. the control of the preparation conditions, such as Ar gas pressure P$\_$Ar/ substrates temperature T$\_$s/, films thickness $\delta$, deposition speed R$\_$d/, is considered to be important to attain ultra high density recording far perpendicular magnetic recording media. In this study, the Co-Cr thin films and Co-Cr-Ta thin films were deposited on the glass side substrates by using Facing Targets Sputtering apparatus(FTS). Crystallographic characteristics and magnetic characteristics were evaluated by X-ray diffractometry(XRD), Vibrating Sample Magnetometer(VSM) respectively.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.6 s.123
• /
• pp.539-546
• /
• 2007

Information storage devices using disks have a disk vibration at the frequency which is equivalent to the disk rotational speed. They also have a track vibration due to the disk eccentricity at the same frequency. In near field recording systems, the former affects the air-gap servo and the latter affects the tracking servo. In this paper, we introduce a novel control algorithm based on the internal model principle to both servos. A controller block designed by the principle is connected to the base lead-lag type compensator in parallel in order to cancel the repeatable run-out due to the disk vibration or eccentricity. Simulation and practical application of the algorithm on a near field recording system show good servo performance.

• Journal of the Institute of Convergence Signal Processing
• /
• v.19 no.3
• /
• pp.125-132
• /
• 2018

KVN(Korean VLBI Network) introduced the Mark6 system of the MIT haystack observatory as a recorder for data recording up to 32 Gbps for VLBI(Very Long Baseline Interferometry) observation. The Mark6 recorder can record data at up to 32Gbps when two systems and 64 HDDs are installed. However, because of the unique recording method that is characteristic of Mark6, we are introducing a large amount of data into a virtual file system, or using a general RAID method, which causes data loss when reading and transferring files at the highest recording speed or file system have. The Flexbuff system, a software recorder developed by JIVE(Joint Institute for VLBI ERIC), can be configured to operate as a data recorder through RAID configuration and network upgrades. In particular, when installed in the Mark6 system, it can record VLBI data at a maximum speed of 32 Gbps with less loss of data compared to the existing Mark6 by utilizing Mark6 resources well. In this paper, we propose that the existing Mark6 system can be operated as Mark6-Flexbuff by installing jive5ab software, and it is verified through experiment that it can be effectively used for VLBI observation operation through data recording test.

• Journal of Welding and Joining
• /
• v.17 no.1
• /
• pp.71-76
• /
• 1999

The real-time holographic interferometer with digital high-speed camera is applied to the experimental study of laser induced plasma/plume in pulsed Nd:YAG laser welding. A pulsed Nd:YAG laser with 1.2 kW average power is applied to generate laser induced plume. The recording speed of the high-speed camera is 3,000 f/s. The high speed photographs of weld plume without another visualization method, are compared with the visualization photographs with holographic interferometer. The radiation intensity from the laser induced plume is recorded by the high speed photographs, which fluctuated during laser radiation and disappeared after laser end. The density distribution of the plume is recorded by the holographic visualization method. The experimental results show the process of generation of the laser induced plasma/plume, and give the feasibility of quantitative measurement of laser induced plume in laser welding.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.378-380
• /
• 2002

There has been lower the tilt margin by the increase of coma aberration due to the reduction of wave-length and the increase of numerical aperture for high density recording. The RF signal degradation is increased as the decrease of tilt margin. To compensate the tilt margin, the optical pick-up actuator for high-speed CD/DVD re-writable system should be able to drive the radial-tilt motion. We announce that the 3-axis drive actuator for high-speed CD/DVD rewritable system. And what was more, the DC/AC sensitivities of this actuator are suitable fur the low-speed playability, the high-speed readability and the high-speed rewritability.

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.165-170
• /
• 2009

The Korean high-speed rail network has been made a remarkable growth recording the world's 4th rank passenger transportation scale during last 5 years after opening the revenue service of Kyoung-bu high-speed line in 2004. However, in spite of it's outstanding growth, Korean Rail technology should meet a demand of intensive technology development in order to prepare a severe competition with an advance parties of worldwide high-speed rail technology. In this paper, the characteristics and new trend of world's rail industry was reviewed based on the most recent statistics and papers of worldwide rail network from UIC and WCR32008. In conclusion, new R&D strategy with choice an concentration for the Korean high-speed rail industry was suggested based on an analysis on the trend of evolution of the state of the art technologies in worldwide high-speed rail system.

• 전기의세계
• /
• v.22 no.3
• /
• pp.79-80
• /
• 1973

This is the abstract of lecture on Electro-optic characteristics of D-KDP crystal and its application for high speed shutter made by Dr. Naomi Furuya; The professor of Yamanashi University in Kofu Japan on March 31, 1973 for KEEI in the auditorium of Korea Electric Company. His lecture is listened by KEEI members that KDP Z-cut crystal can be utilized as a high speed shutter of 10$^{-6}$ second, combining special camera and 2-3KV electrical impulse generator and also recording slide photographs on tungoten lamp crystal voltage and melting fuse phenomena due to over-current taken by this special equipment had been demonstrated.

• 유체기계공업학회:학술대회논문집
• /
• 1997.02a
• /
• pp.188-195
• /
• 1997

The application of PIV to the studies of fluid-machines, especially focused on turbo-machinery is reviewed by scrutinizing the previous investigation. Owing to the inevitable high-speed analysis of turbo-machinery consisting of rotating impellers, the importance of optical setups to cope with illumination problem is frequently mentioned as main ingredient affecting the PIV performance. And the acquisition of the relative velocity and absolute velocity is determined mainly by the optical recording conditions. A few studies cast satisfactory extension of the PIV data to quantitative pressure estimation and related noise assessment.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.57-68
• /
• 1987

The driving pattern was studied in Seoul along nineteen representative routes using a test car equipped with all the instruments required for recording traffic flow and measuring fuel consumption. Speed histories, gear shift points, instantaneous fuel consumption rates, etc. were recorded and the data were anlyzed to determine the traffic characteristics for Seoul. The Seoul-14 Mode has been developed to simulated actual driving conditions in Seoul with respect to fuel consumption. The average speed of the Seoul-14 Mode is 30.1 Km/h and the Mode length is 11.94 Km.