• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제28회 춘계학술대회논문집
• /
• pp.34-37
• /
• 2007

액체산소를 작동유체로 하여 추진제 공급배관에 대한 충진 및 대기 시험을 수행하였다. 추진제 공급 시스템은 추진제 탱크의 출구에 필터가 장착된 형상이다. 추진제의 충진이 완료된 후 대기 과정동안 액체산소의 증발과 이것이 시스템의 재순환 성능에 미치는 영향을 살펴보았다. 추진제의 충진 속도와 탱크 얼리지의 압력이 배관 내 액체산소의 상태에 영향을 미치는 것을 확인하였다. 필터의 장착 위치로 인해 대기 과정동안 배관 내부에서 geysering 현상은 발생하지 않았다.

• 한국미생물·생명공학회지
• /
• 제19권5호
• /
• pp.487-490
• /
• 1991

효모 재순환계에 의한 당밀의 연속발효를 하였다. 단계적으로 YPD배지 농도를 10g/l에서 183.5g/l로 증가시킨 후 최종 발효배지는 당밀로 하였다. 최고의 효모농도는 25g/l였고, 운전중 평균 효모농도는 23.5g/l으로 종래 회분식보다 3.4배 높았다. 최적 발효조건은 180g/l의 당밀배지를 공급하였을 때 교반속도 500rpm, 희석을 0.037$h^{-1}$였다. 이 조건을 645시간 연속 운전하였으며 최고 알코올 생산성은 4.9g$l\cdot h$로서 이때의 희석율은 0.091$h^{-1}$, 알코올 농도는 53.9g/l이었다.

• 반도체디스플레이기술학회지
• /
• 제18권3호
• /
• pp.12-18
• /
• 2019

The protective double layer polymer coatings on silica optical fibers are realized by wet-on-wet liquid coating process and they play an important role in final quality of mass produced optical fibers. This numerical study aims to analyze the effects of secondary coating die design parameters by employing two dimensional axisymmetric model of coating cup and coating die geometry and computational fluid dynamics simulations which include temperature dependent viscosity of polymer coating liquids and viscous dissipation heating. Under high speed fiber drawing conditions and pressurized coating liquid supply, the effects of converging die angle are investigated in order to appreciate the change of coating liquid flow patterns such as flow recirculation zone near coating die as well as primary and secondary coating layer thicknesses. The auxiliary coating die to converging coating die is also tested and the results find that this concept is advantageous in achieving stable double layer coatings on silica glass fiber.

• 한국수소및신에너지학회논문집
• /
• 제30권6호
• /
• pp.578-584
• /
• 2019

The occurrence of white plume in the cooling tower is phenomenon that the steam in the air through the cooling tower fan is condensed again by the cold ambient air to become saturated moist air. Accordingly, this can cause many problems like spoiling landscape around the cooling tower, odor of ambient air, falling accident by frozenness in the winter, and traffic accident, etc. This study was to install the heat exchanger in the inside of the cooling tower in order to prevent the white plume phenomenon in the cooling tower without affecting the performance of cooling tower. In addition, this study was to discharge the part of cooling water into the atmosphere through the recirculation of heat exchanger after creating dry air by heating the saturated moist air to the dew point temperature. At that time, this study was to conduct the experimental study in order to secure the optimal design data to prevent the white plume in the cooling tower because it checked the dry·moist temperature and relative humidity in the inside·outside of cooling tower on the moist air, and evaluated the performance of the heat exchanger.

• 대한기계학회논문집B
• /
• 제29권4호
• /
• pp.469-476
• /
• 2005

Numerical modeling has been carried out to investigate the two-dimensional air flow in automobile interior with a forced exhaust close to main air inlet for typical ventilation modes. The characteristics such as streamlines and temperature fields in the passenger compartment room with the forced exhaust are analyzed with comparison of the cases without a forced exhaust. The simulation results show that air flow on the floor near the front seat is increased with the forced exhaust for all ventilation modes. Flow recirculation in the cabin is most active in mode 2 with a vertical suction inlet in comparison with other two modes. In particular, less time is taken for air temperature to reach the inlet temperature due to the forced exhaust for the ventilation modes. Finally, it could be predicted that ventilating air flow is much improved with the forced exhaust in the interior Modeling results in this study can be applied to the optimal design of automobile interior fur air ventilation system.

• 설비공학논문집
• /
• 제18권10호
• /
• pp.819-825
• /
• 2006

In a SOFC/GT (solid oxide fuel cell/gas turbine) hybrid power generation system, the recuperator is an indispensible component to enhance system performance. Since the expansion ratio to the recuperator core is very large, generally, the effective header design to distribute the flow uniformly before entering the core is crucial to guarantee the required performance. In the present study, we focus on the design of a diffuser type recuperator header with a 90 degree turn inlet port. To reduce the flow separation and recirculation flows, multiple horizontal vanes are used. The number of horizontal vanes is varied from 0 to 24. The air flow velocity is measured at 40 points just behind the core outlet by using a hot wire anemometer. Then, the flow non-uniformity is evaluated from the measured flow velocity. The experimental results showed that inlet air velocity did not effect on relative flow non-uniformity. According to increasing the number of horizontal vanes, flow non-uniformity reduced about $40{\sim}50%$ than without using horizontal vanes.

• Nuclear Engineering and Technology
• /
• 제39권4호
• /
• pp.273-286
• /
• 2007

This paper presents the research activities performed to date for the development of a supercritical pressure water-cooled reactor (SCWR) in Korea. The research areas include a conceptual design of an SCWR with an internal flow recirculation, a reactor core conceptual design, a heat transfer test with supercritical $CO_2$, an adaptation of an existing safety analysis code to the supercritical pressure condition, and an evaluation of candidate materials through a corrosion study. Methods to reduce the cladding temperature are introduced from two different perspectives, namely, thermal-hydraulics and core neutronics. Briefly described are the results of an experiment on the heat transfer at a supercritical pressure, an experiment that is essential for the analysis of the subchannels of fuel assemblies and the analysis of a system safety. An existing system code has been adapted to SCWR conditions, and the process of a first-hand validation is presented. Finally, the corrosion test results of the candidate materials for an SCWR are introduced.

• 한국물환경학회지
• /
• 제39권1호
• /
• pp.76-86
• /
• 2023

We are on the verge of paradigm shift for the design and operation of our urban water systems from treatment- and efficiency-based to recirculation- and sustainability-based. One of the most frequently suggested alternatives to embody this paradigm shift is to decentralize the currently highly centralized urban water infrastructure. However, claims for water infrastructure decentralization are often criticized due to poor economic feasibility, unstable performance, and unprofessional operation and maintenance. The current study critically reviews the literature to discuss the technical advancement needs to overcome such challenges. Firstly, decentralized water infrastructure was briefly defined and the rationale for the proposal of its introduction to the next-generation urban water systems was laid down. The main discussion focused on the following water technologies, which require special attention when working with decentralized water infrastructure: i) material collection, storage, and transport; ii) easily scalable water treatment; iii) sensor, information, and communications; and iv) system optimization. The principles, current development status, and challenges were discussed for each of the water technologies. The discussion on the water technologies has enabled the identification of future research needs for their application to the next-generation urban water systems which will be designed following decentralized water infrastructure. This paper will significantly improve the current understanding on water infrastructure decentralization and provides insight on future direction of water technology development.

• 한국지리정보학회지
• /
• 제12권2호
• /
• pp.69-81
• /
• 2009

본 연구에서는 전산유체역학 모델을 이용하여 도시 재정비에 따른 신축 건물이 주변 대기 흐름에 미치는 영향을 조사하였다. 이를 위하여 지리정보시스템 자료로부터 추출한 건물 자료를 전산유체역학 모델의 입력 자료로 사용하였고 4가지 풍향 (서풍, 남풍, 동풍, 북풍)에 대한 수치 시뮬레이션을 수행하였다. 도시 재정비가 이루어지기 전에는 저층 건물이 밀집되었기 때문에 건물에 의한 마찰 효과가 증가하면서 건물 사이 공간의 풍속이 현저하게 감소하였다. 도시 재정비 계획에 따라 고층 건축물이 신축되고 밀집된 건물이 정비되면서 보행자 고도에서는 건물에 의한 마찰 효과가 감소하였다. 그리고 질량연속방정식을 만족시키기 위한 channeling 효과가 부분적으로 나타나면서 도시 재정비 지역의 풍속이 증가하였다. 상층에서는 고층 건물이 신축되면서 건물 사이에서 일어나는 channeling 효과에 의해 부분적으로 풍속이 증가하였다. 그러나 도시 재정비 지역의 풍하지역에서는 건물에 의해 형성되는 재순환 영역 (recirculation region)과 마찰 효과에 의해 넓은 지역에서 풍속이 현저하게 감소하였다.

• 대한원격탐사학회지
• /
• 제30권6호
• /
• pp.755-767
• /
• 2014

본 연구에서는 LARIAC2 GIS 자료와 전산 유체 역학(CFD) 모델을 이용하여 미국 캘리포니아 주 Los Angeles의 두 지역(Wilshire blvd. & Carondelet and Broadway & $7^{th}$ St.)을 대상으로 수치 실험을 수행하였다. 두 지역의 상세 도시 대기 흐름의 특성을 조사하기 위해 건물 자료 구축 알고리즘을 통해 벡터 형식으로 제공되는 LARIAC2 GIS 자료로부터 건물 도메인 자료를 추출하였다. 추출한 자료를 CFD 모델 입력 자료로 사용하여, 각 지역의 오전과 오후의 주 풍향과 풍속에 대해 수치 실험을 수행하였다. 도시 지역 내에서는 건물에 의해 국소적인 2차 흐름이 발생하면서 유입류와 비교하였을 때, 풍향과 풍속의 차이가 두드러졌다. 유입류와 평행한 방향으로 형성된 도시 협곡에서는 채널링 효과가 나타나면서 풍속이 국지적으로 증가하였고, 수직인 방향으로 형성된 도시 협곡에서는 연직 방향으로 잘 발달한 소용돌이가 형성되었다. 도시 협곡을 이루지 않은 건물의 풍상측에서는 말편자 소용돌이가 지면 근처에서 형성되었고, 풍하측에서는 재순환 영역이 형성되었다. 이와 같은 2차 순환(도시 협곡 소용돌이, 말편자 소용돌이, 재순환 영역)이 형성된 구역에서는 지면 근처의 풍속이 크게 증가하였다. 평균 풍속과 풍향 변화율을 조사한 결과, 대체적으로 풍속 증가율이 높은 곳에서 풍향 변화율이 비교적 낮았고 풍속 감소율이 높은 곳에서는 풍향 변화율이 높게 나타났다.