• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.2
• /
• pp.113-121
• /
• 2013

In this paper, quadruple polarized antenna system with a reconfigurable feeding network is presented. The proposed antenna system consists of the reconfigurable feeding network for fourth polarization such as vertical/horizontal linear polarization and right-handed/left-handed circular polarizations or 45 degree tilted vertical/horizontal linear polarization and patch antenna to receive the signals with various polarizations. In order to receive a signal in any direction, the proposed antenna is designed by electrical switches for reconfigurable polarization. The insertion loss of the designed feeding network in the proposed antenna system is approximately 1.2 dB. The measured 3 dB axial bandwidth and gain of the proposed antenna are about 2 % and 4 dBi(c).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.5C
• /
• pp.469-477
• /
• 2007

Most multimedia source coders exhibit unequal bit error sensitivity. Efficient transmission system design should therefore incorporate the use of matching unequal error protection (UEP). In this paper, we present and evaluate a flexible space-time coding system with unequal error protection. Multiple transmit and receive antennas and bit-interleaved coded modulation techniques are used combined with rate compatible punctured convolutional codes. A near optimum iterative receiver is employed with a multiple-in multiple-out inverse mapper and a MAP decoder as component decoders. We illustrate how the UEP system gain can be achieved either as a power or bandwidth gain compared to the equal error protection system (EEP) for the identical source and equal overall quality for both the UEP and EEP systems. An example with two/three transmit and two receive antennas using BPSK modulation is given for the block fading channel.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.8
• /
• pp.1805-1811
• /
• 2005

We analyzed of the receiver which received OOK and the FSK transmission signal that were a general digital transmission technique in a WDM system. We expressed various error probability with the m which was bandwidth and a bit numerical function and carried out performance evaluation of a receiver in a performance evaluation way. When error probability was $10^{-4}$ which is m=10, as for the receive sensitivity of OOK, the $1.7{\times}10^2$, FSK got $2.2{\times}10^2$ through simulation. And the receive sensitivity of OOK and FSK was able to get each $2.15{\times}10^2$ and $3.07{\times}10^2$ when it was error probability of $10^{-9}$ which is m = 25. Transmission of 23Gb/S showed that it was possible when we does the $10^{-9}$ that was basis error probability of a light communication system with a basis through this, and a coding profit was with for and transmission capacity of 75Gb/s confirmed that it was possible if a code rate was with 0.8.

• Journal of Advanced Navigation Technology
• /
• v.26 no.6
• /
• pp.487-495
• /
• 2022

This paper describes the design and development of a high-power transmit receive module(TRM) for mounting on X-band synthetic aperture radar(SAR) of the NEXTSat-2. The TRM generates a high-power pulse signal with a bandwidth of 100 MHz in the target frequency range of X-band and amplifies a low-noise on the received signal. Tx. path of the TRM has output signal level of more than 200 watts (53.01 dB), pulse droop of 0.35 dB, signal strength change of 0.04 dB during transmission signal output, and phase change of 1.7 ˚. Rx. path has noise figure of 3.99 dB and gain of 37.38 ~ 37.46 dB. It was confirmed the TRM satisfies all requirements. The TRM mounted on the NEXTSat-2 flight model(FM) which will be launched using the KSLV-II (Nuri).

• International Journal of Internet, Broadcasting and Communication
• /
• v.16 no.2
• /
• pp.10-21
• /
• 2024

Recently, audio systems are changing the configuration of conventional sound reinforcement (SR) systems and public address (PA) systems by using audio over IP (AoIP), a technology that can transmit and receive audio signals based on internet protocol (IP). With the advancement of IP technology, AoIP technologies are leading the audio market and various technologies are being released. In particular, audio networks and control hierarchy over peer-to-peer (Anchor) technology based on AoIP is a system that transmits and receives audio signals over a wide bandwidth without an audio mixer, creating a novel paradigm for existing audio system configurations. Anchor technology forms an audio system by connecting audio sources and output equipment with On-site audio center (OAC), a device that can transmit and receive IP. Anchor's receiving OAC is capable of receiving and mixing audio signals transmitted from different IPs, making it possible to configure a novel audio system by replacing the conventional audio mixer. However, Anchor technology does not have the ability to provide audio effects to input devices such as microphones and instruments in the audio system configuration. Due to this, when individual control of each audio source is required, there is a problem of not being able to control the input signal, and it is impossible to individually affect a specific input signal. In this paper, we implemented a tone control module that can individually control the tone of the audio source of the input device using the audio processor core in the audio system based on Anchor technology, tone control for audio sources is possible through a tone control module connected to the transmitting OAC. As a result of the study, we confirmed that OAC receives the signal from the audio source, adjusts the tone and outputs it on the tone control module. Based on this, it was possible to solve problems that occurred in Anchor technology through transmitting OAC and tone control modules. In the future, we hope that the audio system configuration using Anchor technology will become established as the standard for audio equipment.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.10
• /
• pp.1737-1743
• /
• 2006

OCR(On channel repeater) provides the high frequency reuse efficiency for allocating frequency bands to repeaters because the frequency of input and output signals of OCRs is the same. However the oscillation probability of OCRs is high due to the same input and output frequency. In order to prevent a repeater from oscillating, we must keep the antenna isolation higher than the gain of the repeater with a some margin. In this paper we simulated the effects of the amplitude, phase and time delay of feedback signals (m the characteristics of non-regeneration OCR. Simulation results show that the highest probability of oscillation is occurred when the gain of a repeater is the same value of the isolation. From the simulation results, we know that the phase of feedback signals can be adjusted to reduce the possibility of oscillation if a non-regeneration repeater has a narrow operation bandwidth or a signal bandwidth is narrow. As the time delay increases, the probability of oscillation and the fluctuation of gain over a certain frequency band increase also. The effects of the amplitude and phase of feedback signals on S/N of 8-VSB signal for generation and non-generation repeater were tested. The measured results show that the set-top can receive 8-VSB signal when the received signal power is $17{\sim}18dB$ higher than the noise power. When the isolation is almost same as the gain of the repeater, then the set-top can not receive 8-VSB signals due to the oscillation of the repeater. And the phase of feedback signals affects S/N at the output of the repeater when the isolation is $11.75{\sim}13.75dB$ larger than the gain of the repeater. In this case the set-top can not receive 8-VSB signal of at $48^{\circ}\;and\;347^{\circ}$ of the phase of feedback signals. However the phase of feedback signals can not affect the S/N of 8-VSB signals of the generation repeater because of the demodulation and modulation process of the generation repenter. The set-top can not receive 8-VSB signals when the amplitude of feedback signals is $12.6{\sim}13.6dB$ larger than the wanted signal power at the input port of the repeater. It's because that the amplitude of feedback signals saturates the front end of the repeater.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.6
• /
• pp.57-62
• /
• 2008

In this paper, a folded helical monopole antenna for TDMB receiving and a trapezoidal fractal microstrip patch antenna for GPS were designed and fabricated for the vehicle shark antenna. To minimize null which is generating toward antenna axis direction and to receive both vertical polarization and horizontal polarization for TDMB antenna, we fold 90 degree helical monopole element. GPS antenna to get wide bandwidth and gain improvement was designed an air substrate trapezoidal microstrip patch antenna. Fabricated TDMB and GPS antenna were measured for S11 and radiation pattern, and compared with a commercialized antenna. TDMB antenna shows 3 dB higher antenna gain and receiving signal strength than the commercial one. GPS antenna shows the gain of 4.31 dBi at the resonant frequency, which is $3{\sim}5\;dB$ higher gain over whole operating band and 135MHz wide bandwidth at 2:1 VSWR than the conventional ceramic antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.2
• /
• pp.144-150
• /
• 2012

In this paper, circularly polarization patch array antenna of RSE(Road-side Equipment) base station for DSRC(Dedicated Short Range Communication) of ITS(Intelligent Transport System) is proposed. The antenna of RSE base station for DSRC is designed to operate circularly polarization to receive reflected signal from multiplex path effectively. The proposed antenna consisted of microstrip patch and feed line, the slit is inserted in the proximity of the slot of feed structure to generate circularly polarization. The $2{\times}2$ array structure is designed to satisfying gain that DSRC RSE base station antenna required. Measured impedance bandwidth and axial-ratio bandwidth are satisfied by all DSRC band of 5.795~5.855 GHz. Vertical and horizontal HPBW of the proposed antenna are both about 43 degrees, it showed gain characteristic of about 11.21 dBi.

• Journal of IKEEE
• /
• v.16 no.1
• /
• pp.62-68
• /
• 2012

The planar microstrip antenna for the safety communication of life at sea is designed and manufactured to effectively receive the emergency wireless signal from the transmitter on the life vest. The proposed microstrip antenna in this paper is easy to make, light weight and cheap compared to other antennas because of printed antenna fabrication. To overcome the narrow bandwidth, large size and low gain characteristics of microstrip antenna, we use the IDMA(Identical Dual Patch Microstrip Antenna with Air-Gap) structure. The proposed antenna was fabricated with the use of 1.6mm FR4 and measured with the 28.7MHz(6.6%) of bandwidth and 3.04dBi of gain at the frequency of 426MHz. To validate the proposed antenna, we experimented the possible distance range at sea using the commercial UHF transceiver module and obtained over 5km distance for stable communication. This antenna can be widely applied to application of the UHF wireless mobile communication.

• Journal of Broadcast Engineering
• /
• v.23 no.5
• /
• pp.606-613
• /
• 2018

This study is concerned with implementing an external memory expansion device for large-scale image processing. It consists of an external memory adapter card with a PCI(Peripheral Component Interconnect) Express Gen3 x8 interface mounted on a graphics workstation for image processing and an external memory board with external DDR(Dual Data Rate) memory. The connection between the memory adapter card and the external memory board is made through the optical interface. In order to access the external memory, both Programmable I/O and DMA(Direct Memory Access) methods can be used to efficiently transmit and receive image data. We implemented the result of this study using the boards equipped with Altera Stratix V FPGA(Field Programmable Gate Array) and 40G optical transceiver and the test result shows 1.6GB/s bandwidth performance.. It can handle one channel of 4K UHD(Ultra High Density) image. We will continue our study in the future for showing bandwidth of 3GB/s or more.