• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.57-65
• /
• 2006

An approximate function approach has been developed using the subsystem synthesis method for real-time multibody vehicle dynamics models. In this approach, instead of solving loop closure constraint equations of the suspension linkage, approximate functions are used. The approximate function represents the functional relationship between dependent coordinates and independent coordinates of the suspension subsystem. This kinematic relationship is also included in the suspension subsystem equations of motion. Different order of polynomial functions are tried to find out the best candidate functions. The proposed method is also compared with the conventional subsystem synthesis method to verify its efficiency and accuracy.

• International Journal of Automotive Technology
• /
• v.6 no.6
• /
• pp.599-604
• /
• 2005

A functional suspension model is proposed as a kinematic describing function of the suspension, that represents the relative wheel displacement in polynomial form in terms of the vertical displacement of the wheel center and steering rack displacement. The relative velocity and acceleration of the wheel is represented in terms of first and second derivatives of the kinematic describing function. The system equations of motion for the full vehicle dynamic model are systematically derived by using velocity transformation method of multi-body dynamics. The comparison of test and simulation results demonstrates the validity of the proposed functional suspension modeling method. The model is computationally very efficient to achieve real-time simulation on TMS 320C6711 150 MHz DSP board of HILS (hardware-in-the-loop simulation) system for ECU (electronic control unit) evaluation of semi-active suspension.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.199-206
• /
• 2006

Real time vehicle dynamics models have been developed with the subsystem synthesis method for intelligent vehicle HILS system. Three different models for solving subsystem equations are compared in order to find out the best suitable model for HILS applications. The first model is based on the generalized coordinate partitioning technique, and the second one is on the approximate function approach, and the last one is on the constraint stabilization method. To investigate the theoretical efficiency of three proposed methods, arithmetic operators used in the formulations of three models are counted. Bump run simulations with half-sine bump have also carried out with three different models to measure the actual CPU time to validate theoretical investigation.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1714-1717
• /
• 2003

ECCOMAS Thematic Conference Multibody 2003 was held at IST (Instituto Superior Technico), Lisbon, Portugal from July 1 to July 4. 2003. And MBDV(Multibody Dynamics and Vibration) in the 2003 ASME DETC was held at Chicago, U.S.A. from September 2 to September 6. In this paper, the presented papers in these conferences were reviewed and the trends in the multibody dynamics are summarized. The session titles in these conferences include Flexible Multibody Dynamics, Vehicle Dynamics, Contact, Biomechanics, Real-time Challenges, Spatial manipulator and Control, Multidisciplinary Applications, and Advanced Education. The poster session was also organized for more discussions in the Multibody2003 conference.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.4
• /
• pp.359-364
• /
• 2012

Real-Time Traversability should be analyzed from the equiped sensors' data in real time for autonomous outdoor navigation. However, it is difficult to find out such traversability that considers the terrain roughness and the vehicle dynamics especially in case of skid type vehicle. The traversability based on real time dynamic analysis was proposed to solve such problem but in navigation with strait driving path. To adapt the method into the navigation with curved driving path, a path following controller should be incorporated into the dynamic model even though it cause the real time problem. In this paper, a dynamic model is proposed to solve the real time problem in the traversability analysis based on real time dynamic simualtion. The dynamic model contains the control dummy which is connected to the vehicle body with a universal joint to follow the curved path without controller. Simulation and experimental results on $6{\times}6$ articulated unmanned ground vehicle demonstrate the method's effectiveness and applicability into the traversability analysis on terrain with bumps.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.2
• /
• pp.170-176
• /
• 2008

Anti roll bar model for real time multibody vehicle dynamics model has been proposed using kinematic constraint. Anti roll bar have been modeled by kinematic relationship, and mass properties are neglected. Relative angle of torsion bar spring is computed by constraint about drop-link using Newton-Raphson iteration, and then the torque of torsion bar spring can be computed with the angle and torsion spring stiffness. Finally anti roll bar force acting on both knuckle can be calculated. To validate the proposed method, half car simulations of McPherson strut suspension and full car simulations are also carried out comparing with the ADAMS vehicle model with anti roll bar. CPU times are also measured to see the real-time capabilities of the proposed method.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.3
• /
• pp.441-450
• /
• 2022

The introduction of autonomous underwater gliders (AUGs) specifically addresses the reduction of operational costs that were previously prohibited with conventional autonomous underwater vehicles (AUVs) using a "scaling-down" design philosophy by utilizing the characteristics of autonomous drifters to far extend operation duration and coverage. Long-duration, wide-area missions raise the cost and complexity of in-water testing for novel approaches to autonomous mission planning. As a result, a simulator that supports the rapid design, development, and testing of autonomy solutions across a wide range using software-in-the-loop simulation at faster-than-real-time speeds becomes critical. This paper describes a faster-than-real-time AUG simulator that can support high-resolution bathymetry for a wide variety of ocean environments, including ocean currents, various sensors, and vehicle dynamics. On top of the de facto standard ROS-Gazebo framework and open-sourced underwater vehicle simulation packages, features specific to AUGs for ocean mapping are developed. For vehicle dynamics, the next-generation hybrid autonomous underwater gliders (Hybrid-AUGs) operate with both the buoyancy engine and the thrusters to improve navigation for bathymetry mappings, e.g., line trajectory, are is implemented since because it can also describe conventional AUGs without the thrusters. The simulation results are validated with experiments while operating at 120 times faster than the real-time.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.2
• /
• pp.18-28
• /
• 2001

Super computers has been utilized to carry out vehicle dynamics in real time. This research propose an implicit integra-tion method for vehicle state variables. Newton chord method is empolyed to solve the equations of motion and con-straints. The equations of motion and constraints are formulated such that the Jacobian matrix for Newton chord method is needed to be computed only once for a dynamic analysis. Numerical experiments showed that the Jacobian matrix generat-ed at the initial time could have been utilized for the Newton chord iterations throughout simulations under various driving conditions. Convergence analysis of Newton chord method with the proposed Jacobian updating method is carried out. The proposed algorithm yielded accurate solutions for a prototype vehicle multibody model in realtime on a 400 MHz PC compatible.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.5
• /
• pp.666-672
• /
• 2003

This paper presents a design of the controller for vehicle lateral dynamics using active yaw moment. Vehicle lateral motion is incorporated with directional controllability and stability. These are conflicting each other from the view of vehicle handling performance. To compromise the trade-off between these two aspects, we suggest a new control algorithm based on the sliding mode with time-varying switching surface according to the body side slip angle. The controller can deal with the nonlinear region in vehicle driving condition and be robust to the parameter uncertainties in the plant model. Control performance is evaluated from the simulation for the vehicle of real parameters on the road with various tire-road frictions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.1
• /
• pp.109-118
• /
• 2005

A functional suspension model is proposed as a kinematic describing function of the suspension that represents the relative wheel displacement in polynomial form in terms of the vertical displacement of the wheel center and steering rack displacement. The relative velocity and acceleration of the wheel is represented in terms of first and second derivatives of the kinematic describing function. The system equations of motion for the full vehicle dynamic model are systematically derived by using velocity transformation method of multi-body dynamics. The comparison of field test results and simulation results of the ADAMS/Car demonstrates the validity of the proposed functional suspension modeling method. This model is suitable for real-time vehicle dynamics analysis.