• 품질경영학회지
• /
• 제26권4호
• /
• pp.143-150
• /
• 1998

We propose an adaptive monitoring a, pp.oach for serially correlated data. This algorithm uses the adaptive linear prediction lattice filter (ALPLF) which makes it compute process parameters in real time and recursively update their estimates. It involves computation of the forward and backward prediction errors. CUSUM control charts are a, pp.ied to prediction errors simulaneously in both directions as an omnibus method for detecting changes in process parameters. Results of computer simulations demonstrate that the proposed adaptive monitoring a, pp.oach has great potentials for real-time industrial a, pp.ications, which vary frequently in their control environment.

• 산업경영시스템학회지
• /
• 제37권1호
• /
• pp.33-40
• /
• 2014

Air compressor is an important facility with electric power in the industry. However, because of the noise and vibration of air compressor and is installed outside the building management difficulty. In this study, MCP (Micro Control Processor) to remote monitoring of the air compressor via the compressed air through improved quality and allows stable maintenance were designed. So, increase the productivity improvement of energy-saving effect can be obtained. Remote real-time information stored on your PC to manage air compressor equipment was higher reliability. Monitoring system is developed in this study was applied to embedded systems. It is easy to install air compressor, and low maintenance costs was to raise the economic impact.

• 한국산업융합학회 논문집
• /
• 제26권5호
• /
• pp.867-874
• /
• 2023

In this paper, a wireless communication-based sensor data monitoring device with an explosion-proof (Exd IIC) case was implemented to enable installation at explosion-risk industrial sites such as plants. In existing industrial plant sites, most of the temperature sensors and vibration and impact sensors are wired up to several kilometers, which takes a lot of time and money to bury long pipes and cables. In addition, there are not many cases where some wireless devices have been applied to actual plant industry sites due to communication quality problems. Therefore, in order to solve this problem, zigbee mesh wireless communication was applied to provide high reliability wireless communication quality to industrial plant sites, and the time and cost incurred in new or additional installation of sensors could be greatly reduced. In particular, in the event of loss or error of some wireless communication devices, the communication network is automatically bypassed or recovered to enable real-time data monitoring.

• 대한안전경영과학회지
• /
• 제20권3호
• /
• pp.11-19
• /
• 2018

This study suggests a model of production information system that can reduce manufacturing lead time and uniformize quality by using DNC S/W as a part of constructing production information management system in the industrial field of the existing marine engine block manufacturing companies. Under the effect of development of this system, the NC machine interface device can be installed in the control computer to obtain the quality information of the workpiece in real time so that the time to inspect the process quality and verify the product defect information can be reduced by more than 70%. In addition, the reliability of quality information has been improved and the external credibility has been improved. It took 30 minutes for operator to obtain, analyze and manage the quality information when the existing USB memory is used, but the communication between the NC controller computer and the NC controller in real time was completed to analyze the workpiece within 10 seconds.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.564-567
• /
• 2005

For the application of monitoring system of the machine tool to industry, the requirements such as high reliability and low cost need to be satisfied. In this study, a reliable but inexpensive monitoring method for machine tool is introduced. To improve the monitoring reliability, several kinds of information related to machining and operation are selected; real-time video clip from USB camera, operation data and signal from CNC and feed motor torque. Especially, to improve the quality of real-time video clip, a camera housing is developed, it can significantly reduce the vibration effect and prevent from coolant and chip. The collected information are transferred to the monitoring terminals in remote sites using OPC and TCP/IP protocol over Ethernet, which give us convenience of development and interoperability.

• 산업공학
• /
• 제23권3호
• /
• pp.246-256
• /
• 2010

As wireless and mobile technologies have advanced significantly, lots of large sized healthcare organizations have implemented so called mobile hospital (m-Hospital) which provides a location independent and point of care (POC) clinical environment. Implementation of m-Hospital enhances quality of care because health professionals such as physicians and nurses can use hospital information systems at the very place where patients are located without any delay. This paper presents a real-time patient monitoring system based on wireless network technologies. A general framework for the patient monitoring process is introduced and the architecture and components of the proposed monitoring system is described. The system collects and analyzes biometric signals of in-patients who suffer from cancer. Specifically, it continuously monitors oxygen saturation of patients in bed and alarms health professionals instantly when an abnormal status of the patient is detected. The monitoring system has been used and clinically verified in a university hospital.

• 센서학회지
• /
• 제31권2호
• /
• pp.102-106
• /
• 2022

Currently, the demand for real-time monitoring of water quality has increased dramatically. Total organic carbon (TOC) analysis is a suitable method for real-time analysis compared with conventional biochemical oxygen demand (BOD) and chemical oxygen demand (COD) methods in terms of analysis time. However, this method is expensive because of the complicated internal processes involved. The photocatalytic titanium dioxide (TiO2)-based TOC method is simpler as it omits more than three preprocessing steps. This is because it reacts only with organic carbon (OC) without extra processes. We optimized the rate between the TiO2 photocatalyst and binder solution and the TiO2 concentration. The efficiency was investigated under 365 nm UV exposure onto a TiO2 coated substrate. The optimized conditions were sufficient to apply a real-time monitoring system for water quality with a short reaction time (within 10 min). We expect that it can be applied in a wide range of water quality monitoring industries.

• KIEE International Transactions on Power Engineering
• /
• 제4A권4호
• /
• pp.214-220
• /
• 2004

Power quality monitoring is the cornerstone for power quality analysis, diagnosis and improvement. The measurement of power quality (PQ) evolves from instantaneous metering to continuous monitoring. Furthermore, recent technologies enable us to construct more flexible, reliable, rapid and economical power quality monitoring system (PQMS). Therefore, this paper presents an improved PQMS with a new distributed monitoring structure. The proposed PQMS consists of a PQ meter, PQ analyzer and GUI. The PQ meter only collects raw data and the PQ analyzer performs power quality analysis. It has several advantages compared to conventional structures in economic efficiency, modularity, speed, etc. PQ monitoring algorithms to catch steady-state trends and to detect PQ events are also adapted to the proposed structure. Using the proposed structure and monitoring algorithm, a prototype PQMS is constructed and real-time testing is performed.

• 한국환경보건학회지
• /
• 제43권4호
• /
• pp.267-272
• /
• 2017

Objectives: The purposes of the study were to analyze the temporal variation of carbon dioxide ($CO_2$) and particulate matter (PM) in daycare centers and evaluate the appropriateness of the official test method of one-time measurement. Methods: Indoor air quality in 46 daycare centers in the Seoul Metropolitan Area was measured as specified in the official test method of Indoor Air Quality Management law. In addition, indoor air quality in the 46 daycare centers was measured over 37 days using a real-time monitor (AirGuard K). Results: The daily means of $CO_2$ and PM in the 46 daycare centers were $1042.74{\pm}134.45ppm$ and $67.60{\pm}18.25{\mu}g/m^3$, respectively. Indoor air quality in the daycare centers showed significant temporal fluctuation. Measurements for single days were significantly different from the 37-day average exposure. Relative error of short term exposure decreased with an increase in the number of sampling days. The noncompliance rate for $CO_2$ using the official testing method was 2.17%, and none exceeded the $PM_{10}$ standard of $100{\mu}g/m^3$. With monitoring over 37 days, the daily noncompliance rate for $CO_2$ was 50.4% and the daily noncompliance rate for PM was 13.8%. Conclusions: When the official test method evaluates the indoor air at daycare centers one day per year, the results may not represent actual indoor air quality over a longer period of time. Real-time monitoring devices could be an alternative for managing indoor air quality.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2022년도 춘계학술대회
• /
• pp.306-309
• /
• 2022

최근 우리나라에서도 지진 발생빈도가 급격히 증가하면서 지진에 대한 관심도가 높아지고 있다. 지진발생 시 대응과 복구도 중요하지만, 관리 취약점을 사전에 찾아내어 예방 및 사전 대비 활동을 수행하는 것이 필요하다. 한국수자원공사에서는 지진으로부터 안전한 시설관리를 위해 지진가속도계측기를 운영하여 실시간 지진데이터를 수집하고 있으며, 대외기관에서 지진데이터를 활용할 수 있도록 데이터를 전송하고 있다. 운영 중인 지진감시시스템의 관리 취약점을 사전에 줄이고자 지진데이터의 수집지연시간을 최소화하고, 빅데이터를 활용한 지진데이터의 실시간 품질분석 체계·기반 구축으로 고품질의 데이터 생산이 가능하다. 이에 따라 댐 안전관리 및 고품질의 지진데이터를 확보하여 대외기관에 신속한 데이터를 제공함으로써 지진재해로부터 국민의 생명과 재산을 보호할 수 있을 것으로 기대된다.