• Journal of information and communication convergence engineering
• /
• v.5 no.3
• /
• pp.215-218
• /
• 2007

In this paper, amorphous semiconductor and insulator thin film are etched using reactive ion etcher. At that time, we experiment in various RIE conditions (chamber pressure, gas flow rate, rf power, temperature) that have effects on quality of thin film. The using gases are $CF_4,\;CF_4+O_2,\;CCl_2F_2,\;CHF_3$ gases. The etching of a-Si:H thin film use $CF_4,\;CF_4+O_2$ gases and the etching of $a-SiO_2,\;a-SiN_x$ thin film use $CCl_2F_2,\;CHF_3$ gases. The $CCl_2F_2$ gas is particularly excellent because the selectivity of between a-Si:H thin film and $a-SiN_x$ thin film is 6:1. We made precise condition on dry etching with uniformity of 5%. If this dry etching condition is used, that process can acquire high yield and can cut down process cost.

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.1
• /
• pp.33-38
• /
• 2009

We have investigated the effect of the ambient gases on the characteristics of AZO thin films for the OLED (organic light emitting diodes) devices. These AZO thin films are deposited by rf-magnetron sputtering under different ambient gases (Ar, Ar+$O_2$, and Ar+$H_2$) at 300. In order to investigate the influences of the oxygen and hydrogen, the flow rate of oxygen and hydrogen in argon mixing gas has been changed from 0.2sccm to 1sccm and from 0.5sccm to 5sccm, respectively. The AZO thin films were preferred oriented to (002) direction regardless of ambient gases. The electrical resistivity of AZO film increased with increasing flow rate of $O_2$ under Ar+$O_2$ while under Ar+$H_2$ atmosphere the electrical resistivity showed minimum value near 1sccm of $H_2$. All the films showed the average transmittance over 80% in the visible range. The OLED device was fabricated with different AZO substrates made by configuration of AZO/$\acute{a}$-NPD/DPVB/$Alq_3$/LiF/Al to elucidate the performance of AZO substrate.

• Journal of the Korean Vacuum Society
• /
• v.19 no.5
• /
• pp.341-346
• /
• 2010

In this paper, anti-reflection coating was investigated for decreasing the reflection in visible range of 400~650 [nm] through four staked layers of $Si_xO_y$ and $Si_xN_y$ thin films prepared by reactive sputtering method. Si single crystal of 6 [inch] diameter was used as a sputtering target. Ar and $O_2$ gases were used as sputtering gases for reactive sputtering for the $Si_xO_y$ thin film, and Ar and $N_2$ gases were used for reactive sputtering for the $Si_xN_y$ thin film. DC pulse power of 1900 [W] was used for the reactive sputtering. Refractive index and deposition rate were 1.50 and 2.3 [nm/sec] for the $Si_xO_y$, and 1.94 and 1.8 [nm/sec] for the $Si_xN_y$ thin film, respectively. Considering the simulation of the four layer anti-reflection coating structure with the above mentioned films, the $Si_xO_y-Si_xN_y$ stacked four-layer structure was prepared. The reflection measurement result for that structure showed that a "W" shaped anti-reflection was obtained successfully with a reflection of 1.7 [%] at 550 [nm] region and a reflection of 1 [%] at 400~650 [nm] range.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.75-78
• /
• 2005

Using a low-energy Ar+ ion-beam with and without reactive gases, polymers such as chemically stable poly(ether ether ketone) (PTFE) and poly(ether ether ketone) (PEEK) films were modified to have special surface features. The adhesion strength between the polymers and the copper was significantly improved because of both changes in the surface topography and chemical interactions due to polymer surface functionalization (oxidation and amination). The surface modification altered the failure mode from adhesive failure for the unmodified polymer/Cu interface to cohesive failure for the surface-modified polymer/Cu layer interface..

• Proceedings of the Korean Vacuum Society Conference
• /
• 1996.06a
• /
• pp.149-149
• /
• 1996

• Journal of the Korean Ceramic Society
• /
• v.40 no.8
• /
• pp.739-745
• /
• 2003

In $N_{x}$ films were deposited on soda-lime glass without substrate heating by reactive dc magnetron sputtering using indium (In) metal target. Depositions were carried out under various total gas pressures ( $P_{tot}$) of mixture gases (Ar+$N_2$ or He+$N_2$). He gas was introduced to $N_2$ gas in order to enhance the reactivity of nitrogen on film surface by the "penning ionization". Plasma impedance decreased greatly when 20% or more introduced the $N_2$ gas. This is due to the In $N_{x}$ layers formed on target surface because a secondary electron emission rate of InN is small compared with In metal. XRD patterns of the films revealed that <001> preferred oriented polycrystalline In $N_{x}$ films, where the crystallinity of the films was improved with decrease of $P_{tot}$ and with increase of $N_2$ flow ratio. The improvement of the crystallinity and stoichimetry of the In $N_{x}$ films were considered to be caused by an increase in the activated nitrogen radicals and also by an increase in the kinetic energy of sputtered In atoms arriving at growing film surface, which should enhance the chemical reaction and surface migration on the growing film surface, respectively. Furthermore, the films deposited using mixture gases of He+$N_2$ showed higher crystallinity compared with the film deposited by the mixture gases of Ar+$N_2$.$.EX>.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.1
• /
• pp.1-4
• /
• 2019

Reactive sputtering is widely used because of its high deposition rate and high step coverage. The deposition layer is often affected by target poisoning because the target conditions are changed, as well, by reactive gases during the initial stage of sputtering process. The reactive gas affects the deposition rate and process stability (target poisoning), and it also leads unintended oxide interlayer formation. Although the target poisoning mechanism has been well known, little attention has been paid on understanding the interlayer formation during the reactive sputtering. In this research, we studied the interlayer formation during the reactive sputtering. A DC magnetron sputtering process is carried out to deposit an aluminum oxide film on a silicon wafer. From the real-time process monitoring and material analysis, the target poisoning phenomena changes the reactive gas balance at the initial stage, and affects the interlayer formation during the reactive sputtering process.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.49.2-49.2
• /
• 2010

Copper oxide films have been deposited on silicon substrates by direct current magnetron sputtering of Cu in O2 / Ar gas mixtures. The target oxidation occurring as a result of either adsorption or ion-plating of reactive gases to the target has a direct effect on the discharge current and the resulting composition of the deposited films. The kinetic model which relates the target oxidation to the discharge current was proposed, showing the one-to-one relationship between discharge current characteristics and film stoichiometry of the deposited films.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2006.04a
• /
• pp.581-582
• /
• 2006

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.25-28
• /
• 2001

In this paper, we have investigated the effects of gas flow rate, rf power, process pressure and Ar addition on reactive ion etching of InP, InGaAs and InAlAs using Sic14 and Cl$_2$ gases. The etch rates were measured by using a surface profiler. The etched profiles, sidewall roughness, and surface morphology were observed by scanning electron microscopy and by atomic force microscopy. The selective etching of InGaAs to InP and InAlAs was studied by varying the etching parameters. It was found that Cl$_2$ gas is more efficient for the selective etching of InGaAs to InAlAs than SiCl$_4$ gas. The etch selectivity of InGaAs to InAlAs is strongly dependent on the rf power and the process pressure.