• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.12
• /
• pp.65-71
• /
• 1996

A novel lateral field emitter triode has been designed and fabricated. It has self-vacuum environmets and low turn-on voltage, so that the chief problems of previous field emission devices such as additional vacuum sealing process and high turn-on voltage are settled. An in-situ vaccum encapsulation empolying recessed cavities by isotropic RIE (reactive ion etch) method and an electron beam evaporated molybdenum vacuum seals are implemented to fabricate the new field emitter triode. The device exhibits low turn-on voltage of 7V, stabel current density of 2.mu.A/tip at V$_{AC}$ = 30V, and high transconductance (g$_{m}$) of 1.7$\mu$S at V$_{AC}$ = 22V. The superb device characteristics are probably due to sub-micron dimension device structure and the pencil type lateral cathode tip employing upper and lower LOCOS oxidation.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.328-331
• /
• 1988

Sealed Interface Local Oxidation (SILO) technology has been investigated using a nitride/oxide/nitride three-layered sandwich structure. P-type silicon substrate was either nitrided by rapid thermal processing, or silicon nitride was deposited by LPCVD method. A three-layered sandwich structure was patterned either by reactive ion etch (RIE) mode or by plasma mode. Sacrificial oxidation conditions were also varied. Physical characterization such as cross-section analysis of field oxide, and electrical characterization such as gate oxide integrity, junction leakage and transistor behavior were carried out. It was found that bird's beak was nearly zero or below 0.1um, and the junction leakages in plasma mode were low compared to devices of the same geometry patterned in RIE mode, and gate oxide integrity and transistor behavior were comparable. Conclusively, SILO process is compatible with conventional local oxidation process.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1998.09a
• /
• pp.85-90
• /
• 1998

Reactive ion etching (RIE) of Ta-Al alloy thin film and SiO2 thin films was observed during the etching with the CF4 gas and the could be used effectively to etch the Ta-Al alloy thin film. The etching rate of the thin film at a Ta content of 50 mol% was about 67$\AA$/min. No selectivity between the Ta-Al alloy thin film and SiO2 thin films was observed during the etching with the CF4 gas and the etching rate of the SiO2 layer was 12 times faster than that of the Ta-Al alloy thin film. In addition, it was observed that photoresist of AZ5214 was more useful than Shiepley 1400-2 in RIE with the CF4 gas.

• Electrical & Electronic Materials
• /
• v.7 no.5
• /
• pp.425-429
• /
• 1994

In this paper, we study on the plasma polymerized styrene as a negative electron-beam resist. Plasma polymerized thin film was prepared using an interelectrode inductively coupled gas-flow type reactor. We show that polymerization parameters of thin film affect sensitivity and etching resistance of the resist. Molecular weight distribution of plasma polymerized styrene is 1.41-3.93, and deposition rates of that are 32-383[.angs./min] with discharge power. Swelling and etching resistance becomes . more improved with increasing discharge power during plasma polymerization. Etch rate by RIE is higher than that by plasma etching.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.93-99
• /
• 2011

This paper presents a new type of optical silicon accelerometer using deep reactive ion etching (DRIE) and micro-stereolithography technology. Optical silicon accelerometer is based on a mass suspended by four vertical beams. A vertical shutter at the end of the mass can only moves along the sensing axis in the optical path between two single-mode optical fibers. The shutter modulates intensity of light from a laser diode reaching a photo detector. With the DRIE technique for (100) silicon, it is possible to etch a vertical shutter and beam. This ensures low sensitivity to accelerations that are not along the sensing axis. The microstructure for sensor packaging and optical fiber fixing was fabricated using micro stereolithography technology. Designed sensors are two types and each resonant frequency is about 15 kHz and 5 kHz.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.1
• /
• pp.60-63
• /
• 1999

Application of reactive ion etching (RIE) technique to Ta-Al alloy thin film with a thickness of $1000{\AA}$ was studied. $CF_{4}$ gas could be used effectively to etch the Ta-Al alloy thin film. The etching rate in the thin film with Ta content of 50 mol% was about $67{\AA}/min$. NO selectivity between the Ta-Al alloy film and $SiO_{2}$ film was observed during the etching using the $CF_{4}$ gas. The etching rate of the $SiO_{2}$ layer was 12 times faster than that of the Ta-Al alloy thin film. It was also observed that photoresist of AZ5214 was more useful than Shiepley 1400-27 in RIE with the $CF_{4}$ gas.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.4
• /
• pp.20-25
• /
• 2010

An integrated Mach-Zehnder interferometric sensor operating at 632.8 nm was designed and fabricated by the technology of planar rib waveguides. Rib waveguide based on silica system ($SiO_2-SiO_xN_y-SiO_2$) was geometrically designed to have single mode operation and high sensitivity. It was structured by semiconductor fabrication processes such as thin film deposition, photolithography, and RIE (Reactive Ion Etching). With the power observation, propagation loss measurement by cut-back method showed about 4.82 dB/cm for rib waveguides. Additionally the chromium mask process for an etch stop was employed to solve the core damaging problem in patterning the sensing zone on the chip. Refractive index measurement of water/ethanol mixture with this device finally showed a sensitivity of about $\pi$/($4.04{\times}10^{-3}$).

• Journal of the Korean Vacuum Society
• /
• v.13 no.3
• /
• pp.120-126
• /
• 2004

A damage-reduced trench was investigated in view of the defect distribution along trench sidewall and bottom using high resolution transmission electron microscopy, which was formed by HBr plasma and additive gases in magnetically enhanced reactive ion etching system. Adding $O_2$ and other additive gases into HBr plasma makes it possible to eliminate sidewall undercut and lower surface roughness by forming the passivation layer of lateral etching. To reduce the RIE induced damage and obtain the fine shape trench corner rounding, we investigated the hydrogen annealing effect after trench formation. Silicon atomic migration on trench surfaces using high temperature hydrogen annealing was observed with atomic scale view. Migrated atoms on crystal surfaces formed specific crystal planes such as (111), (113) low index planes, instead of fully rounded comers to reduce the overall surface energy. We could observe the buildup of migrated atoms against the oxide mask, which originated from the surface migration of silicon atoms. Using this hydrogen annealing, more uniform thermal oxide could be grown on trench surfaces, suitable for the improvement of oxide breakdown.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.1038-1041
• /
• 2003

In the paper, we investigated silicon surface microstructures formed by reactive ion etching in hollow cathode system. Wet anisotropic chemical etching technique use to form random pyramidal structure on <100> silicon wafers usually is not effective in texturing of low-cost multicrystalline silicon wafers because of random orientation nature, but High density hollow cathode plasma system illustrates high deposition rate, better film crystal structure, improved etching characteristics. The etched silicon surface is covered by columnar microstructures with diameters form 50 to 100nm and depth of about 500nm. We used $SF_{6}$ and $O_{2}$ gases in HCP dry etch process. This paper demonstrates very high plasma density of $2{\times}10^{12}$ $cm^{-3}$ at a discharge current of 20 mA. Silicon etch rate of 1.3 ${\mu}s/min$. was achieved with $SF_{6}/O_{2}$ plasma conditions of total gas pressure=50 mTorr, gas flow rate=40 sccm, and rf power=200 W. Our experimental results can be used in various display systems such as thin film growth and etching for TFT-LCDs, emitter tip formations for FEDs, and bright plasma discharge for PDP applications. In this paper we directed our study to the silicon etching properties such as high etching rate, large area uniformity, low power with the high density plasma.

• Applied Chemistry for Engineering
• /
• v.16 no.6
• /
• pp.853-856
• /
• 2005

Inductively coupled plasma reactive ion etching of magnetic tunnel junction (MTJ) stack, which is one of the key elements in magnetic random access memory, was studied. The MTJ stacks were patterned in nanometer size by electron(e)-beam lithography, and TiN thin films were employed as a hard mask. The etch process of TiN hard mask was examined using Ar, $Cl_2/Ar$, and $SF_6/Ar$. The TiN hard mask patterned by e-beam lithography was first etched and then the etching of MTJ stack was performed. The MTJ stacks were etched using Ar, $Cl_2/Ar$, and $BCl_3/Ar$ gases by varying gas concentration and pressure.