• 전력전자학회논문지
• /
• 제18권6호
• /
• pp.593-600
• /
• 2013

The asymmetric pulsed DC reactive magnetron sputtering system is widely used for the high quality plasma sputtering process such as a thin film deposition. In asymmetric pulsed DC power supply a reverse voltage is applied to the target periodically to minimize arc discharging effect. When sputtering in the mid-frequency range (20-350 kHz), the periodic target voltage reversals suppress arc formation at the target and provide long-term process stability. Thus, high quality, defect-free coatings of these materials can now be deposited at competitive rates. In this paper, a new style asymmetric pulsed DC power supply including mid-transformer is presented. In the proposed, an energy recovery circuit is adopted to reduce the mutual inductance of the transformer. As a result, the system dynamics of the voltage control loop is increased highly and the non-linear voltage boosting effect of the conventional system is removed. This work was proved through simulation and laboratory based experimental study.

• Journal of Korean Vacuum Science & Technology
• /
• 제3권2호
• /
• pp.130-133
• /
• 1999

Paraelectric ZrTiO4 thin films were synthesized on a Si(100) substrate using DC magnetron reactive sputtering. Films deposited above-400$^{\circ}C$ exhibited crystalline characteristics. The dielectric constants ($\varepsilon$) and dielectric losses (tan$\delta$) of as-deposited and annealed films were measured in the 1 MHz range using a Pt upper electrode and a phosphorous-doped si bottom electrode. Preliminary data showed that as the deposition temperature increased, the dielectric losses decreased while the dielectric constants did not change significantly. similar trends for dielectric losses were observed when the as-deposited samples were annealed at 800$^{\circ}C$. The reduction of dielectric losses at high-deposition temperatures and post annealing correlated well with the x-ray diffraction peak widths.

• 한국표면공학회지
• /
• 제37권3호
• /
• pp.169-174
• /
• 2004

MgO thin films were reactively deposited using an internal inductively coupled plasma assisted sputtering method varying reactive gas ratio to get stoichiometric film composition, and bipolar dc substrate bias to suppress micro arcs. The minimum frequency required for arc suppression was about 10KHz depending on ICP power. Their crystallinity was analyzed using X-ray diffraction and surface morphology using AFM. The surface was very smooth with rms roughness less than 0.42nm. The preferred orientation of the films were changing from (200) to bulk-like characteristics as Ar: $O_2$ratio was controlled to 10 : 2. Optical emission spectroscopy revealed that there were two distinct discharge modes: a blue one and a green one, where enhanced emission from Ar and Mg were observed. This cannot simply be understood by metallic or oxide mode of reactive sputtering due to ICP coupled to magnetron discharge.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 춘계학술대회 논문집
• /
• pp.35-38
• /
• 1995

Indium Tin Oxide(ITO) thin film is transparent to visible ray and conductive in electricity. It is seen that the samples made by the sputtering process have high transmission rate to visible ray and high adhesion , but the planar type magnetron sputtering process with is very well known in industrial region have a defect of partial erosion on the surface of target and a high loss of target and also since the substrate is positioned in plasma, the damage on thin film surface is caused by the reaction with plasma. In cylindrical magnetron sputtering system. it is known that the loss of target is little , the damage of thin film is very little and the adhesion of thin film with substrate is strong. In this study, we have made ITO thin film in the cylindrical DC magnetron system with the variable of substrate temperature , magnetic field, vacuum condution and the applied voltage. The general temperature for formation on ITO is asked at 350 $^{\circ}C$~400$^{\circ}C$ but we have made ITO is low temperature(80-150$^{\circ}C$) By studing electrical and optical properties of ITO thin fims made by varing several condition, we have searched the optimal condition for formation in the best ITO in low temperature.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1999년도 추계학술발표강연 및 논문개요집
• /
• pp.25-25
• /
• 1999

• 한국표면공학회지
• /
• 제45권5호
• /
• pp.206-211
• /
• 2012

Process analysis was carried out during deposition of MgO by inductively coupled plasma assisted reactive magnetron sputtering in Ar and $O_2$ ambient. At the initiation of Mg sputtering with bipolar pulsed dc power in Ar ambient, total pressure showed sharp increase and then slow fall. To analyse partial pressure change, QMS was used in downstream region, where the total pressure was maintained as low as $10^{-5}$ Torr during plasma processing, good for ion source and quadrupole operation. At base pressure, the major impurity was $H_2O$ and the second major impurity was $CO/N_2$ about 10%. During sputtering of Mg in Ar, $H_2$ soared up to 10.7% of Ar and remained as the major impurity during all the later process time. When $O_2$ was mixed with Ar, the partial pressure of Ar decreased in proportion to $O_2$ flow rate and that of $H_2$ dropped down to 2%. It was understood as Mg target surface was oxidized to stop $H_2$ emission by Ar ion sputtering. With ICP turned on, the major impurity $H_2$ was converted into $H_2O$ consuming $O_2$ and C was also oxidized to evolve CO and $CO_2$.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 1998년도 추계학술발표회 초록집
• /
• pp.55-56
• /
• 1998

• 한국세라믹학회지
• /
• 제40권8호
• /
• pp.739-745
• /
• 2003

In $N_{x}$ films were deposited on soda-lime glass without substrate heating by reactive dc magnetron sputtering using indium (In) metal target. Depositions were carried out under various total gas pressures ( $P_{tot}$) of mixture gases (Ar+$N_2$ or He+$N_2$). He gas was introduced to $N_2$ gas in order to enhance the reactivity of nitrogen on film surface by the "penning ionization". Plasma impedance decreased greatly when 20% or more introduced the $N_2$ gas. This is due to the In $N_{x}$ layers formed on target surface because a secondary electron emission rate of InN is small compared with In metal. XRD patterns of the films revealed that <001> preferred oriented polycrystalline In $N_{x}$ films, where the crystallinity of the films was improved with decrease of $P_{tot}$ and with increase of $N_2$ flow ratio. The improvement of the crystallinity and stoichimetry of the In $N_{x}$ films were considered to be caused by an increase in the activated nitrogen radicals and also by an increase in the kinetic energy of sputtered In atoms arriving at growing film surface, which should enhance the chemical reaction and surface migration on the growing film surface, respectively. Furthermore, the films deposited using mixture gases of He+$N_2$ showed higher crystallinity compared with the film deposited by the mixture gases of Ar+$N_2$.$.EX>.

• Applied Science and Convergence Technology
• /
• 제23권3호
• /
• pp.145-150
• /
• 2014

MgO thin films were deposited by internal ICP-assisted reactive-magnetron sputtering with bipolar pulse bias on a substrate to suppress random arcs. Mg is reactively sputtered by a bipolar pulsed DC power of 100 kHz into ICP generated by a dielectrically shielded internal antenna. At a mass flow ratio of $Ar/O_2$ = 10 : 2 and an ICP/sputter power ratio of 1 : 1, optimal film properties were obtained (a powder-like crystal orientation distribution and a RMS surface roughness of approximately 0.42 nm). A bipolar pulse substrate bias at a proper frequency (~a few kHz) prevented random arc events. The crystalline preferred orientations varied between the (111), (200) and (220) orientations. By optimizing the plasma conditions, films having similar bulk crystallinity characteristics (JCPDS data) were successfully obtained.

• 한국표면공학회지
• /
• 제55권6호
• /
• pp.353-362
• /
• 2022

Recently, transmittance of photomasks for ultra-violet (UV) region is getting more important, as the light source wavelength of an exposure process is shortened due to the demand for technologies about high integration and miniaturization of devices. Meanwhile, such problems can occur as damages or the reduction of yield of photomask as electrostatic damage (ESD) occurs in the weak parts due to the accumulation of static electricity and the electric charge on chromium metal layers which are light shielding layers, caused by the repeated contacts and the peeling off between the photomask and the substrate during the exposure process. Accordingly, there have been studies to improve transmittance and antistatic performance through various functional coatings on the photomask surface. In the present study, we manufactured antireflection films of Nb₂O₅, | SiO₂ structure and antistatic films of ITO designed on 100 × 100 × 3 mmt sodalime glass by DC magnetron sputtering system so that photomask can maintain high transmittance at I-line (365 nm). ITO thin film deposited using In/Sn (10 wt.%) on sodalime glass was optimized to be 10 nm-thick, 3.0 × 103 𝛺/☐ sheet resistance, and about 80% transmittance, which was relatively low transmittance because of the absorption properties of ITO thin film. High average transmittance of 91.45% was obtained from a double side antireflection and antistatic thin films structure of Nb₂O₅ 64 nm | SiO₂ 41 nm | sodalime glass | ITO 10 nm | Nb₂O₅ 64 nm | SiO₂ 41 nm.