• Tribology and Lubricants
• /
• 제17권6호
• /
• pp.426-434
• /
• 2001

The hermetic reciprocating compressor driven by the BLDC motor rotating with variable speeds, is modelled and analyzed for dynamic characteristics. The governing equations of piston, connecting rod and crank-shaft of the reciprocating compression mechanism and characteristics of driving torque of the motor are obtained. Dynamic behavior of the crankshaft supported on 2 journal bearings is analyzed considering compression load and eccentric unbalance for the 4 rotating speeds of crankshaft. And. reaction forces generated from oil film in the journal bearings are analyzed under transient condition using Reynolds' equation. To take into account the dynamic characteristics depending on the variable rotating speeds, comparison on the dynamic behavior of crank-shaft is made for the 4 operating modes of the compressor. Results show that the magnitude of crankshaft locioperating on the lower rotating speeds is more larger than the higher ones due to reduction of inertia force of the reciprocating piston.

• 한국산학기술학회논문지
• /
• 제16권5호
• /
• pp.3653-3659
• /
• 2015

방향족 열방성 액정 고분자와 에틸렌-아크릴 산 공중합체 및 그 금속염 고분자간의 반응 상용화에 관하여 연구하였다. 블렌드는 배치 믹서에서 제조하였으며 액정 고분자의 에스터 그룹과 이오노머의 아크릴산 사이에 발생하는 acidolysis 반응으로 형성되는 그라프트 공중합체의 발생 유무를 평가하였다. 반응의 정도는 배치 믹서에서 시간에 따른 토크의 증가와 열분석 및 형태학 상 구조를 통해 평가하였다. poly(ethylene-co-acrylic acid) (EAA) 이오노머의 Na 염이 반응을 증진시키는데 특히 효과적임을 알 수 있었다. 반응의 진행 정도는 금속염의 종류 뿐 아니라 이오노머의 조성과 반응 시간에 따라 변하였다. 액정 고분자와 Na로 중화된 이오노머 간의 반응으로 생성된 그라프트 공중합체는 액정 고분자와 EAA 이오노머 블렌드의 반응상용화제로 효과가 높음을 미세 구조 분석을 통하여 알 수 있었다.

• 한국운동역학회지
• /
• 제22권1호
• /
• pp.55-63
• /
• 2012

The purpose of this study was to investigate the balance differences between skilled players and less-skilled players during Hakdariseogi motion of Keumgang Poomsae in Taekwondo. To achieve the study goal, total of 10 Taekwondo athletes; 5 skilled players(S, body mass: $67.0{\pm}5.7$ kg, height: $174.0{\pm}4.8$ cm, age: $20.0{\pm}2.0$ yrs) and 5 less-skilled players(LS, body mass: $73.0{\pm}4.9$ kg, height: $176.4{\pm}6.1$ cm, age: $20.8{\pm}1.3$ yrs) participated in this study. A three-dimensional motion analysis with 8 infrared cameras and one force plate whose sampling frequency as 30 Hz and 300 Hz, respectively, were performed. Participants' motion were divided into three phases which were preparation phase(P1), performing phase(P2) and maintaining phase(P3). The range and velocities of COP, the range and RMS of ground reaction torque and displacement between COM and center of BOS of each phase were computed. In this study, at P1 and P3 which were double and single stance, respectively, the range and M-L velocities of COP revealed significantly higher in LS compared with those of S(p<.05). At P2 which was single stance, LS indicated significantly higher in range of COP and ground reaction torque, and M-L velocities of COP than those of S(p<.05). The significantly shorter displacement between COM and center of BOS, however, was found in LS compared with that of S(p<.05). The results from our study indicated that S revealed more stable performance and a better posture control ability during performing Hakdariseogi motion.

• PNF and Movement
• /
• 제5권1호
• /
• pp.49-56
• /
• 2007

Objectives : We find that the reaction force on the elbow joint during elbow flexion, extension with and without an object in the hand can be calculated the equations of motion that the sum of the torque and the sum of the force acting on the elbow joint must be zero and (moment of inertia x angular acceleration) and (mass x acceleration). Methods : we have calculated the equations of motion (${\Sigma}F=0$, ${\Sigma}{\tau}=0$, ${\Sigma}F=ma$, ${\Sigma}{\tau}=Ia$) to investigate the reaction force on the elbow joint during elbow flexion, extension by means of the simplified free-body technique for coplanar forces. Results : we found that the reaction force on the elbow joint during elbow flexion, extention as constant acceleration motion is more than constant velocity, static motion. Also, we found that the relation between during flexion and during extension like this ; $J_{flexion}$ < $J_{extension}$.

• 제어로봇시스템학회논문지
• /
• 제14권10호
• /
• pp.1029-1037
• /
• 2008

When a humanoid robot pushes an object with its force, it is essential to adequately control its posture so as to maximize the surplus torque far all joints. For such purpose, this study proposes a method to find an optimal posture of a humanoid robot using a genetic algorithm in such a way that the surplus torque for all joints is maximized. In this study, pushing motion of an 18-DOF humanoid robot is considered. When the robot takes a cooperative motion to push an object, the palms and soles are assumed to be fixed at the object and ground respectively, and are subjected to sense the reaction force from the object and the ground. Then, the torques for all joints are calculated and reflected to fitness function of the genetic algorithm. To verify the effectiveness of the proposed method, a number of simulations with different fitness functions are carried out. The simulation result shows that the proposed method can be adopted to find optimized posture in cooperative motion of a humanoid robot.

• 한국정밀공학회지
• /
• 제23권1호
• /
• pp.145-151
• /
• 2006

Wheel bearing unit has been exclusively applied to car wheel supporting device. The seal for wheel bearing is required to have both high sealing effects and low reaction forces because wheel bearing are operated on adverse environmental conditions such as mud and splash water. High sealing effects are for the protection of bearing ball wear from dust influx. In order to ensure high sealing effects, it is a easiest way to increase contact force which are affected by geometric characteristics, material properties and interferences between seal and inner bearing but induces higher wear phenomena. Interferences in all variables are most important factor to determine the performance of wheel bearing. In this study, optimization of interference amount was performed with finite element analysis with commercial code ABAQUS. For the sake of finite element analysis, tensile tests of rubber material were conducted and governing equation of nonlinear behavior was achieved. Hock-up bearing was manufactured with optimized interference amount. Results of torque and mud spray tests using this bearing unit are performed. Less torque and moisture influx of bearing with optimized interference amount is evidence to validity of this study.

• 한국항공우주학회지
• /
• 제31권9호
• /
• pp.55-63
• /
• 2003

본 연구에서는 다수의 추력기를 이용한 발사체 상단 RCS 자세 제어 시스템에 대해 다룬다. 이때 추력기 배치 위치와 부착 각도에 따라 시스템 응답 특성, 연료소모량, 추력 분배로직에 의한 유효 토크량, 고장대응 용이성이 달라진다. 최적화 기법을 이용하여 27개의 명령에 대해 명령 방향과 일치하면서 최대 응답 토크량을 갖도록 하는 최적의 배치를 찾는 방법을 제안하였다. 기존에 주어진 추력기 배치 형상과 제안된 추력기 배치 형상에 대한 수치 해석 결과를 비교함으로서 제안된 추력기 배치 형상에 정당성을 찾고자 한다.

• KSBB Journal
• /
• 제4권2호
• /
• pp.78-86
• /
• 1989

에너지소모를 최소화하고 최대의 당화효과를 얻을 수 있는 고효율 당화장치의 개발을 목표로 impeller교반형 bioattritor를 설계, 제작하여 불용성 섬유소를 기질로 실험하였다. Bioattrotor의 효용성과 효소당화촉진 mechan-ism을 규명하였으며, 최적운전조건을 검토하였다. 분쇄 마찰매체함유 반응기에 일정한 탄성계수를 지닌 spiral spring coil을 내장한 torzue측정장치를 개발, 부하되는 torque, power, 그리고 소요에너지를 측정하여 이를 당화촉진과 비교함으로서 bioattritor의 경제성을 검토하였다. 분쇄마찰매체의 첨가량 및 종류, impeller형태, 교반속도는 중요한 요소로서 작용하였다. 비록 더 연구가 필요하나 분쇄마찰매체의 교반에 소모되는 동력은 당화 촉진효과의 증대에 따른 당화시간의 단축과 섬유소의 고효율 전환에 따른 고농도당의 확보등에 의해 보상되리라 예상된다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.545-548
• /
• 2002

Turbines have been known to be particularly susceptible to flow-induced self-excited vibration. In such vibrations, direct damping and cross stiffness effects of aerodynamic forces determine rotordynamic stability. In axial turbines with eccentric shrouded rotors, the non-uniform sealing gap causes azimuthal non-uniformities in the seal gland pressure and the turbine torque which destabilize the rotor system. Previously, research efforts focused solely on either the seal flow or the unshrouded turbine passge flow. Recently, a model for flow in a turbine with a statically offset shrouded rotor has been developed and some stiffness predictions have been obtained. The model couples the seal flow to the passage flow and uses a small perturbation approach to determine nonaxiymmetric flow conditions. The model uses basic conservation laws. Input parameters include aerodynamic parameters (e.g. flow coefficient, reaction, and work coefficient); geometric parameters (e.g. sealing gap, depth of seal gland, seal pitch, annulus height); and a prescribed rotor offset. Thus, aerodynamic stiffness predictions have been obtained. However, aerodynamic damping (i.e. unsteady aerodynamic) effects caused by a whirling turbine has not yet been examined. Therefore, this paper presents a new unsteady model to predict the unsteady flow field due to a whirling shrouded rotor in turbines. From unsteady perturbations in velocity and pressure at various whirling frequencies, not only stiffness but also damping effects of aerodynamic forces can be obtained. Furthermore, relative contributions of seal gland pressure asymmetry and turbine torque asymmetry are presented.

• 한국소음진동공학회논문집
• /
• 제26권3호
• /
• pp.258-264
• /
• 2016

This paper presents the experimental result and theoretical analysis result to investigate the correlation between the operating force and locking torque for vehicle hood frame. Also, we derived the experimental equations that using the results of experiment and theory. The hood frame is switching-devices used for opening and closing the vehicle hood. It needs the correlation data between locking torques of each joint and operating force of hood frame because the parameters affects the emotional quality of the vehicle. The correlation data for torque and force of hood frame obtained through experiment and theory analysis. Finally, two experimental equations of correlation are derived. Thus, the developed equations show that has high usefulness for the basic design of hood frame of vehicle.