• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.140-140
• /
• 2018

The 3D interconnect technologies have been appeared, as the density of Integrated Circuit (IC) devices increases. Through Silicon Via (TSV) process is an important technology in the 3D interconnect technologies. And the process is used to form a vertically electrical connection through silicon dies. This TSV process has some advantages that short length of interconnection, high interconnection density, low electrical resistance, and low power consumption. Because of these advantages, TSVs could improve the device performance higher. The fabrication process of TSV has several steps such as TSV etching, insulator deposition, seed layer deposition, metallization, planarization, and assembly. Among them, TSV metallization (i.e. TSV filling) was core process in the fabrication process of TSV because TSV metallization determines the performance and reliability of the TSV interconnect. TSVs were commonly filled with metals by using the simple electrochemical deposition method. However, since the aspect ratio of TSVs was become a higher, it was easy to occur voids and copper filling of TSVs became more difficult. Using some additives like an accelerator, suppressor and leveler for the void-free filling of TSVs, deposition rate of bottom could be fast whereas deposition of side walls could be inhibited. The suppressor was adsorbed surface of via easily because of its higher molecular weight than the accelerator. However, for high aspect ratio TSV fillers, the growth of the top of via can be accelerated because the suppressor is replaced by an accelerator. The substitution of the accelerator and the suppressor caused the side wall growth and defect generation. The suppressor was used as Single additive electrodeposition of TSV to overcome the constraints. At the electrochemical deposition of high aspect ratio of TSVs, the suppressor as single additive could effectively suppress the growth of the top surface and the void-free bottom-up filling became possible. Generally, copper was used to fill TSVs since its low resistivity could reduce the RC delay of the interconnection. However, because of the large Coefficients of Thermal Expansion (CTE) mismatch between silicon and copper, stress was induced to the silicon around the TSVs at the annealing process. The Keep Out Zone (KOZ), the stressed area in the silicon, could affect carrier mobility and could cause degradation of the device performance. Cobalt can be used as an alternative material because the CTE of cobalt was lower than that of copper. Therefore, using cobalt could reduce KOZ and improve device performance. In this study, high-aspect ratio TSVs were filled with cobalt using the electrochemical deposition. And the filling performance was enhanced by using the suppressor as single additive. Electrochemical analysis explains the effect of suppressor in the cobalt filling bath and the effect of filling behavior at condition such as current type was investigated.

• Culinary science and hospitality research
• /
• v.20 no.4
• /
• pp.14-26
• /
• 2014

This study investigated the physicochemical and sensory characteristics of muffins prepared with various amounts(0, 3, 6, 9, 12%) of yacon powder. The specific gravity of the muffins prepared by adding yacon powder was higher than that of the control group. The height of the muffins added with 3% yacon powder was higher than that of the other groups. The weight of the muffins prepared with yacon powder showed no significant difference among all the sample groups. The volume and specific loaf volume of the muffins were decreased by addition of yacon powder. The baking loss rate of the muffins prepared by adding yacon powder showed no significant difference among all the sample groups. The moisture content of the muffins was increased, but their pH was decreased significantly by addition of yacon powder. DPPH radical scavenging activity of the control group was 21.45%, whereas the muffins prepared with yacon powder ranged from 57.23~85.46%. The a value of redness was increased, but L and b values were decreased significantly by addition of yacon powder. The springiness, cohesiveness and brittleness of textural properties of the muffins were decreased significantly by addition of yacon powder. Sensory evaluation scores in terms of appearance, taste, texture and overall preference for the muffins showed that 6~9% substituted sample groups were higher than those of the others. The results of this study suggest that adding 6~9% of yacon powder was the best substitution ratio for muffins.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.32-32
• /
• 2017

To increase rice production, manipulating plant architecture, especially developing new high-yielding cultivars with erect leaves, is crucial in rice breeding programs. Leaf inclination angle determines the light extinction coefficient (k) of the canopy. Erect leaves increase light penetration into the canopy and enable dense plantings with a high leaf area index, thus increasing biomass production and grain yield. Because of erect leaves, the high-yielding indica rice cultivar 'Takanari' has smaller k during ripening than 'Koshihikari', a japonica cultivar with good eating quality. In our previous study, using chromosome segment substitution lines (CSSLs) derived from a cross between 'Takanari' and 'Koshihikari', we detected seven quantitative trait loci (QTLs) for leaf inclination angle on chromosomes 1 (two QTLs), 2, 3, 4, 7, and 12. In this study, we developed a near-isogenic line (NIL-3) carrying a 'Takanari' allele for increased leaf inclination angle on chromosome 3 in the 'Koshihikari' genetic background. We compared k, dry matter production, and grain yield of NIL-3 with those of 'Koshihikari' in the field from 2013 to 2016. NIL-3 had higher inclination angles of the flag, second, and third leaves at full heading and 3 (- 4) weeks after full heading and smaller k of the canopy at the ripening stage. Biomass at full heading and leaf area index at full heading and at harvest did not significantly differ between NIL-3 and 'Koshihikari'. However, biomass at harvest was significantly greater in NIL-3 than in 'Koshihikari' due to a higher net assimilation rate at the ripening stage. The photosynthetic rates of the flag and third leaves did not differ between NIL-3 and Koshihikari at ripening. Grain yield was higher in NIL-3 than 'Koshihikari'. Higher panicle number per square meter in NIL-3 contributed to the higher grain yield of NIL-3. We conclude that the QTL on chromosome 3 increases dry matter and grain production in rice by increasing leaf inclination angle.

• IMMUNE NETWORK
• /
• v.1 no.2
• /
• pp.151-161
• /
• 2001

Background: Inactivation in p53 tumor suppressor gene through a point mutation and deletion is one of the most frequent genetic changes found in human cancer, with 50% of an incidence. This high rate of mutation mostly suggests that the gene plays a central role in the development of cancer and the mutations detected so far were found in exons 5 to 8. Mutation of p53 locus produced accumulation of abnormal p53 protein, and negative regulation of cell proliferation and transcriptional activation as a suppressor of transformation were lost. In addition, inhibition of its normal cellular function of wild-type by mutant is an important step in tumorigenesis. Method: 4 colon cancer cell lines (SNU C1, C2A, C4, C5) were examined for mutation in exons 5 to 8 of the p53 tumor suppressor gene by PCR-SSCP analysis and expression pattern by western blotting and immunoprecipitation. p53-mediated transactivation ability were examined by CAT assay and base substitution of p53 in SNU C2A cell were detected by DNA sequencing. Results: 1) SNU C2A cell and SNU C5 cell were detected mobility shifts each in exon 5 and exon 7 of p53 gene by the PCR-SSCP method, implicating being of p53 mutation. 2) 3 colon cancer cell lines (SNU C1, SNU C2A, SNU C5) expressed wild type and mutant type p53 protein. 3) In northern blot experiment, SNU C2A and SNU C5 cell expressed high level of p53 mRNA. 4) Results of p53-mediated transactivation in colon cancer cell lines by CAT assay represented only SNU C2A cell has transcriptional activity. 5) DNA sequencing in SNU C2A cell showed missense mutation in codon 179 of one allele, histidine to arginine and wild type p53 in the other allele. Conclusion: Colon cancer cell lines showed correlation with mutation in p53 gene and accumulation of abnormal p53 protein. Colon cancer cell SNU C2A retained p53-mediated transactivation as heterozygous p53 with one mutant allele in 179 codon and the other wild-type allele.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.10
• /
• pp.6019-6023
• /
• 2013

Lung cancer, one of the leading causes of cancer-related deaths, usually appears as solitary pulmonary nodules (SPNs) which are hard to diagnose using the naked eye. In this paper, curvelet-based textural features and clinical parameters are used with three prediction models [a multilevel model, a least absolute shrinkage and selection operator (LASSO) regression method, and a support vector machine (SVM)] to improve the diagnosis of benign and malignant SPNs. Dimensionality reduction of the original curvelet-based textural features was achieved using principal component analysis. In addition, non-conditional logistical regression was used to find clinical predictors among demographic parameters and morphological features. The results showed that, combined with 11 clinical predictors, the accuracy rates using 12 principal components were higher than those using the original curvelet-based textural features. To evaluate the models, 10-fold cross validation and back substitution were applied. The results obtained, respectively, were 0.8549 and 0.9221 for the LASSO method, 0.9443 and 0.9831 for SVM, and 0.8722 and 0.9722 for the multilevel model. All in all, it was found that using curvelet-based textural features after dimensionality reduction and using clinical predictors, the highest accuracy rate was achieved with SVM. The method may be used as an auxiliary tool to differentiate between benign and malignant SPNs in CT images.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.4
• /
• pp.355-365
• /
• 2015

This study examined the fluidity and strength properties, water resistance, durability, and freeze-thaw of cementless loess mortar using an eco-friendly hardening agent. The experimental result indicates that 28 days compressive and flexural strength of the loess mortar was increased regardless of the weathered granite soil and loess mixture ratio as the replacement ratio of the hardening agent increases. The strengths were significantly increased until 14 days regardless of the hardening agent, while the effect on the strengths increasement was relatively low after 14 days. Thus, the strength development of loess mortar concrete was found to be faster than that of the normal concrete. In addition, when the hardening agent of 10% was used, the average flexural strength was 1.7MPa which is insufficient compared to the 28-day flexural strength of 4.5MPa for the paving concrete. However, the flexural strengths of the loess mortar concrete using the hardening agents of 20% and 30% were 4.0MPa and 5.3MPa, respectively. Thus, the hardening agent need to be at least 20% so that the loess mortar can be used for paving concrete. The experiment for water resistance shows that the repeated absorption and dry reduced mass regardless of the mixing ratio of the loess. The maximum length change also decreased with increasing the substitution rate loess mixture ratio and the hardening agent. The result of the freeze-thaw resistance test indicates that the relative dynamic modulus of elasticity at 300 cycle freeze-thaw with the hardening agents of 20% and 30% were 75% and 79%, relatively. Thus, the hardening agent of at least 20% is required to obtain the relative dynamic modulus of elasticity of 60% for the loess mortar.

• Journal of the Korea Concrete Institute
• /
• v.25 no.2
• /
• pp.241-250
• /
• 2013

As the amount of construction wastes increase, reuse of demolished concrete is being considered in research areas. Reflecting these interests, this experiment was performed to clarify concrete's mechanical property and workability using recycled aggregate as a coarse aggregate. Eleven cases of concrete specimens were produced by changing the rates of replacement of coarse recycled aggregate, replacement of fly ash, design strength, and moisture state of coarse aggregate. Compressive and tensile split strength tests were taken to study the mechanical properties of hardened concrete. To verify flowability of fresh concrete, a slump test and a flow curve test using ICAR Rheometer were performed. It was found that using recycled aggregate and fly ash leads good workability by testing slump and flow curve. The yield stress of fresh concrete decreased with increase of recycled aggregate substitution rate. Through the test, it was confirmed that there is inversely proportional relationship between the slump and yield stress roughly. Recycled aggregate concrete containing fly ash has considerably lower plasticity viscosity than not containing fly ash. Strength test results showed that recycled aggregate tended to decrease compressive and tensile strength of concrete, when recycled aggregate was used as a coarse aggregate. Using over 30% recycled aggregate caused significant decreases in compressive and tensile strength. Replacing 30% cement with fly ash was helpful to improve the long-term strength of concrete.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.27 no.1
• /
• pp.45-52
• /
• 2007

This study was conducted from 2003 to 2005 at crop field of National Institute of Subtropical Agriculture, RDA, in Jeju. The treatment consisted of chemical fertilizer 100%(CF 100%, T1), cattle manure 100%(CM 100%, T2), CF 50%+CM 50%(T3), CF 25%+CM 75%(T4), CM 100%(1st yr.)+CF 100%(2nd yr,)+CM(3rd yr)(T5), CM 100%(1st yr.)+CF 100%(2nd yr.)+CF(3rd yr.)(T6). The highest substitution effect of chemical fertilizer for cattle manure indicated that the highest yield(Avg. 11,169 kg/ha) obtained from CM 100%(1 yr.)+CF 100%(2 yr.) treatment. The forage yield of CM 100%(1 yr.)+CF 100%(2 yr.) was 4% more than CM 100% application whereas was 3% less than CF 100% application. Changes of physical and chemical properties of soils for applications of CF 100% and CM 100% was clearly in cattle manure application. Especially, cattle manure application in pasture were superior to chemical fertilizer application with respect to organic matter(OM, %), total nitrogen(T-N, %), and avaliable phosphorous($P_2O_5$, %) contents of soils. In this present study, cattle manure application recorded slightly lower forage yields than CF 100% application but the combined use of cattle manure and chemical fertilizer was attribute to reduction of chemical fertilizer application rate as well as maintaining soil health on long-term basis.

• Korean Journal of Agricultural Science
• /
• v.10 no.2
• /
• pp.393-405
• /
• 1983

The demand for livestock and poultry products including beef, pork, chicken, egg and milk whose income elasticities are relatively higher than other staple foods, has been increased significantly during the past two decades in response to the remarkable increase in per capita GNP. This trend will be continued during the fifth and the sixth five year economic development plan period beginning with 1982. The annual GNP growth rate will be 7.5% on the average during the next 10 years. It is greatly needed to estimate the demand for beef, pork, chicken egg and milk and to study the feasibilities of domestic production of livestock products for the formulation of adequate policies in order to equate the consumption and the production during the 1980s. So this study reviewed the possible changes in the food consumption patterns during the 1980s, estimated the demand for beef, pork, chicken, egg and milk by using empirical demand functions and finally made suggestions for the formulation of long term price stabilization policies for each livestock, poultry and dairy products through the equilibrium of the quantity of demand for and supply of the products. There are many factors affecting the demand for meats, but this study considered own price, prices of supplements and substitutes and per capita income as the independent variables in the demand equations. It was found that it's own price and income were most significantly affecting factors among others and the degree of substitution effects were remarkably different among the products. According to the meat demand derived in this study, per capita consumption of beef, pork and chicken in the base year 1982 was 11.2kg for total meat, 2.5kg beef, 6.0kg pork and 2.5kg chicken, 106 pieces egg, 15.1kg milk respectively, while those in 1991 were 19.3kg for total meat, 4.8kg beef, 9.6kg pork, 4.9kg chicken, 133pieces egg and 44.1kg milk. It is also predicted through this study that, when the level of production costs be maintained, the domestic production of pork and chicken will meet the demand for them during the fifth and sixth five year economic plan period. However, there will be chronic shortage of beef supply during the coming years. The annual import requirement will be 30,000tons to 40,000tons during the period. In order to stabilize the domestic livestock and poultry and dairy products market, the government should introduce measures to curb the increase in beef consumption by encouraging the consumption of pork and chicken. For this, the livestock production policy measures should be concentrated on : 1) the improvement of infrastructures of beef production by introducing advanced feeding and management technology, subsidies for the establishment of facilities and price support programs for farmers : 2) the development of dairy beef : 3) the reinforcement of the forecast systems for pork and chicken production and consumption.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.4
• /
• pp.327-337
• /
• 2007

Mineral compositions were determined using quantitative X-ray diffraction analysis on the three kinds of Youngdong illite consisting of white, yellow and refined yellow samples. Mean particle size and their size distribution patterns were measured by laser particle size analyzer. The characteristics of phosphate adsorption on illite were studied through batch adsorption experiments. The white illite has less illite content, but is finer than that of yellow. The refined yellow illite has more illite content and finer particle size compared with those of raw yellow illite. The adsorption rate of phosphate generally increases when the mass of illite increases, whereas adsorption quantity decreases with ascending pH. The phosphate adsorption usually increases with ascending illite content or descending particle size. Although the white illite has lower illite content than the yellow, the former has higher phosphate adsorption quantity than the latter. This can be ascribed to the fine particle size, high interlayer charge, and low substitution in tetrahedral site of white illite. The adsorption isotherms of white illite are well fitted with the Langmuir equation, however those of yellow one are better with Freundlich equation.