• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.266-267
• /
• 2014

In order to develop concrete generating compressive strength of 10MPa~15MPa aging for 6hours in the room temperature curing, Hardening accelerator containing Ca²⁺ mixed with rapid hardening portland cement containing C₃S in quantity. The result was that the more addictive contents of Hardening accelerator is, the more greatly early compressive strength was improved. That's because the composition of Ca(OH)₂ was mass-produced at early-ages.

• 한국건축시공학회지
• /
• 제16권3호
• /
• pp.279-288
• /
• 2016

The fundamental performance of any construction material should cover at least two phases: safety and serviceability. Safety commonly represents adequate strength, while serviceability encompasses the control of cracking and deflections at service loads. With respect to rapid hydraulic binders as a construction material, the above two phases should also be considered. Recent research on rapid cooling ladle furnace slag (RC-LFS) has drawn much attention, particularly given that it shows remarkable rapid hydraulic ability to pulverize to a fineness of $6,300cm^2/g$. This industrial byproduct could contribute to developing the sustainability of the rapidly hardening cementitious material system. This paper aims to expand upon the applicability of an RC-LFS-based binder that is composed of two parts. It also seeks to illustrate the engineering performance of an RC-LFS-based hybrid fiber-reinforced composite and to increase the strength of the RC-LFS-based composite. Each step of this experiment followed ASTM standards. The engineering performance, in both fresh state and hardening state, was tested and discussed in this paper. According to the experimental results for fresh concrete, the air content increased following the addition of polypropylene fiber. For hardened concrete, the toughness and strength improved following the addition of a hybrid fiber. The hybrid fiber mixture, which contains 0.75% of steel fiber and 0.25% of polypropylene fiber, shows even better engineering performance than other mixtures.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.607-612
• /
• 2002

In road pavements, it is known that cement concrete pavement has superior durability, safety compared. But in repairing pavement, cement concrete pavement is not usually applied because of the length of time while the road is interrupted when using Ordinary and Rapid-hardening Portland Cement. And Super High Early Strength Cement and Ultra Super High Early Strength Cement are not favorable for ready mixed concrete because of rapid setting time, high slump loss and other restrictions. We developed special cement developing 1 day strength of over 30.0N/mm$^2$ to open the road within 1 day and workable time is maintained over 1 hour so that it can be used as ready mixed concrete. We performed experimental overlay construction with the cement and evaluated the mechanical property and the durability. At curing temperature of 8-l8$^{\circ}C$,the flexural strength was 6.4N/mm$^2$at 1 day, so that the road can be open to traffic within 1 day. In durability test, the hardened concrete showed higher durability than Portland cement concrete.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.217-220
• /
• 2001

Due to the tendency of increase in demolished-concrete produced by alteration and deterioration of concrete structures, recycling of those demolished-concrete is necessary to solve the exhaustion of natural aggregate, in order to save resources and protect environment, especially being want of resources in Korea. For this purpose, concrete made with the pozzolanic cement and recycled aggregate was tested for compressive and tensile strength. The pozzolanic cement was a mixture of OPC(Ordinary Portland Cement) and pozzolans such as fly ash, other siliceous materials and early rapid hardening cement(ERC). It was found that the compressive strength of the pozzolanic cement was enhanced when 0.75% of ERC was dozed, as compared with OPC mortar. It was also shown that compressive and tensile strength of concrete with recycled aggregate and pozzolanic cement were higher than those of concrete with crushed stones and OPC. It was concluded that the pozzolanic cement influenced on the increase of concrete strengths with recycled aggregate.

• 한국지반환경공학회 논문집
• /
• 제11권1호
• /
• pp.53-59
• /
• 2010

해수 침적 조건에서 시멘트 수화물이 부식되는 화학적 열화과정은 콘크리트 구조물이나 주입공사 목적물에서 동일하다. 국내에서 사용되고 있는 MSG(Micro Silica Grouting)주입재는 실리카질 물질이 다량 함유된 혼합계 시멘트로서 분말도가 $8,000cm^2/g$ 이상으로 높기 때문에 수화활성도가 매우 크고, 고강도 및 고내구성을 특징으로 하며, $C_3A$ 함유량도 5% 이하로 내황산염시멘트 규격을 만족하는 내해수성 시멘트재로 평가된다. 따라서, 본 논문에서는 내해수성이 우수한 MSG와 국내에서 사용되고 있는 급결재를 조합하여 내해수성 특성을 실험적으로 평가하였다. 국내에서 일반적으로 규산계 고활성 급결재 또는 초속경시멘트계 무기질 급결재가 사용되고 있다. 이들 급결재와 MSG가 조합된 주입재의 호모겔 시편에 대해서 압축강도, 중량변화 및 길이변화 특성을 실험적으로 평가하여 내해수성이 우수한 주입재 조합을 제시하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.217-219
• /
• 2012

In this study, the experiment was conducted in the level of mortar as one of the basic studies on pre-cast concrete which acceleration curing is not done. This study has the purpose to develop the strength of mortar into 20MPa within 6 hours in the condition of room temperature using admixtures which can accelerate C3S hydration reaction. In this experiment, W/C was fixed into 20%, PCE which can stimulate C3S was used as an accelerating admixture. From the results of this experiment, maximum content of accelerating admixture was 1%. Also, as more than 20MPa was measured through 6-hour compressive strength, it can be known that strength can be developed without steam-curing.

• Computers and Concrete
• /
• 제13권6호
• /
• pp.695-707
• /
• 2014

This study investigated the chloride binding isotherms of various cement types, especially the contributions of C-S-H and AFm hydrates to the chloride binding isotherms were determined. Ordinary Portland cement (OPC), Modified cement (MC), Rapid-hardening Portland cement (RHC) and Low-heat Portland cement (LHC) were used. The total chloride contents and free chloride contents were analyzed by ASTM. The contents of C-S-H, AFm hydrates and Friedel's salt were determined by X-ray diffraction Rietveld (XRD Rietveld) analysis. The results showed that OPC had the highest chloride binding capacity, and, LHC had the lowest binding capacity of chloride ions. MC and RHC had very similar capacities to bind chloride ions. Experimental equations which distinguish the chemically bound chloride and physically bound chloride were formulated to determine amounts of the bound chloride basing on chloride binding capacity of hydrates.

• 한국지반신소재학회논문집
• /
• 제14권3호
• /
• pp.13-20
• /
• 2015

하수관거 시공시 부적절한 뒤채움재 및 다짐불량으로 인해 하수관로 파손 및 지반침하 현상이 발생한다. 최근들어 이러한 문제점을 해결하기 위해 유동성 채움재에 대한 관심이 증가하고 있다. 본 연구에서는 속경성, 가소성, 유동성, 수중불분리성을 갖춘 뒤채움재의 최적배합 도출과 뒤채움재의 경제성 향상을 위한 기초 연구를 수행하였다. 속경성 결합재의 최적배합 도출 실험 결과를 통해 뒤채움재의 최적 배합의 특성을 평가하였다. 시험결과, 속경성 결합재 페이스트의 W/M을 100%까지 증가시켜도 가소제 첨가량을 적절히 조절하여 사용하면 요구 성능을 만족시킴과 동시에 경제성 또한 확보 할 수 있을 것으로 사료된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제21권3호
• /
• pp.27-34
• /
• 2017

최근 유통 물류 산업의 발달로 산업용 창고 바닥의 중요성a이 점점 높아지고 있다. 본 연구에서는 기존의 바닥재료로 사용되어 온 일반 시멘트계 모르타르가 가지고 있는 유동성의 한계 및 긴 양생 시간 등의 단점을 보완할 수 있는 속경성 폴리머 모르타르 바닥소재를 개발하였다. 속경성 확보를 위해 초속경 시멘트를 결합재로 사용하였고, VAE 폴리머 분말수지를 5%~20% 혼입 범위로 설정한 4종류의 배합과 혼입하지 않은 Proto배합에 대한 기초물성을 유동성실험, 압축강도실험, 휨강도실험, 부착강도실험 및 마모실험을 통해 평가하였다. 유동성 실험결과를 통해 고성능 감수제량를 조절함으로써 플로우 250 mm 이상의 고유동 특성을 확보할 수 있었다. VAE 폴리머 혼입은 압축강도 감소에 영향을 미치는 것으로 나타났지만 휨강도는 Proto배합에 비해 우수하게 증진시킬 수 있어 압축강도/휨강도비를 증가시키는 것으로 평가되었다. 또한 최소 2.6배 이상의 부착강도 향상과 4배 이상의 마모저항성을 확보할 수 있었다. 역학적 실험을 통해 VAE 폴리머 최적 혼입률을 10%로 결정하였고, 현장적용 및 모니터링을 수행한 결과 VAE 폴리머를 혼입하지 않은 바닥재에 비해 오염도, 충격에 의한 저항, 부착성능 등이 우수한 것으로 나타났다.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제24권1호
• /
• pp.35-42
• /
• 2019

In installation of groundwater wells, grouting materials are injected between the groundwater borehole and the inner casing in order to prevent infiltration of contaminated groundwater from the top soil layers into wells. The injection device of grouting materials is commonly composed of an inlet head device with an expansion packer, a cylinder capable of storing the grouting materials, and an air cylinder. In this work, two types of common grouting materials, silicon and cement materials, were tested for their performances as grouting media. For silicon. silicon was mixed with clay or calcite, and tested for their tensile strength and underwater reactivity. Both silicon-clay and silicon-calcite mixtures had adequate flow and adhesiveness. For cement material, general cement, ultra-rapid harding cement, and natural cement were respectively mixed with three different soil types including coarse-grained granite, fine-grained granite, and gneiss, and direct shearing tests were conducted after hardening. Under grouting depth condition of 30 m, the minimum adhesive strength was greater for weathered gneiss than non-weathered gneiss with its maximum values obtained from the mixtures of ultra rapid-harding cement.