• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04b
• /
• pp.65-68
• /
• 2002

The effect of low-temperature ZnO buffer layer has been investigated for the optical properties of ZnO thin films. ZnO buffers and thin films have been deposited using the pulsed laser deposition technique. ZnO buffer layers were grown at $200^{\circ}C$ with various thickness of 0 to 60 nm, followed by raising the substrate temperature to $400^{\circ}C$ to grow $2{\mu}m$ ZnO thin films. The buffer layers could relax stresses induced by the lattice mismatch and different thermal expansion coefficients between ZnO thin films and sapphire substrate. In order to identify the optical properties of ZnO thin films, PL measurement was used. From the results of PL measurement, all the fabricated ZnO thin films with buffer layers have shown intensive UV emission with a narrow linewidth. ZnO thin films with buffer layer of 20 nm have shown the strongest UV emission. It was found that the use of ZnO buffer layer plays an important role to improve the intensive UV emission of the ZnO thin films.

• Journal of the Speleological Society of Korea
• /
• no.71
• /
• pp.1-4
• /
• 2006

Chloromethylnaphthalene is a valuable compound for obtaining of the plant growing stimulator - -napthylacetic acid. Chloromethylation of naphthalene by paraformaldehyde in the presence of glacial acetic acid, phosphoric and hydrochloric acids at temperature 80 - 85C and duration - 6 hours the -chloromethylnaphthalene yield was 55-57%. Using Box-Wilson method for mathematical planning of experiment carried out optimization of its synthesis for purpose increasing -chloromethylnaphthalene yield. Preliminary, one - factor experiments were carried out for selecting independence main parameters influencing on the synthesis. A full factor experiment of 23 with extended matrix of planning was used for optimization. Aiming to increase the -chloromethylnaphthalene yield, the obtained mathematical model was used for program of sharp raising on the reply surface. The received optimal conditions for the -chloromethylnaphthalene synthesis were selected as following: molar ratio of naphthalene parapfsormaldehyde of 1 : 2 temperature - 105C duration of the reaction - 3 hours. The yield of -chloromethylnaphthalene under these optimal conditions was 75%.

• Journal of Fisheries and Marine Sciences Education
• /
• v.9 no.2
• /
• pp.188-197
• /
• 1997

The fracture toughness of three different kinds of epoxy-matrix composites containing the same volume fraction of reinforcement and the variation of fracture toughness of glass-carbon fiber/epoxy hybrid composites due to the change of test temperature and different glass fiber content were investigated in this study. Glass fiber/epoxy composite provided much higher fracture toughness than that of other composites because of the high strain at failure of glass fiber. Particularly the carbon fiber/epoxy composite exhibited the low fracture toughness caused by the low strain energy absorbing capacity of carbon fiber. And it was found that the strain at failure of reinforcement and interfacial delamination absorbing a significant amount of impact energy played an important role to increase fracture toughness of composites. The fracture toughness of the glass-carbon fiber hybrid composites increased with increasing the glass fiber content and decreased with raising the test temperature. The residual stress arising from the different thermal expansion between the matrix and reinforcement influenced the fracture toughness of composites.

• Journal of Software Engineering Society
• /
• v.27 no.1
• /
• pp.15-17
• /
• 2018

Fast response to livestock disease and raising the reproductive success rate contribute to the improvement of farm productivity and profit margins. Due to the decrease in farm workforce and aging population, efficient livestock healthcare and breeding management are needed. In this study, we developed a mobile application for livestock healthcare and breeding management based on the collected body temperature data by IoT sensors. In case of livestock health problem, users are notified immediately via a mobile application warning message. It also provides users with a livestock breeding date function, allowing them to respond without missing the breeding season.

• Journal of Sensor Science and Technology
• /
• v.29 no.1
• /
• pp.40-44
• /
• 2020

An integrated multifunctional sensor, capable of raising an early electric-fire warning, was fabricated. An arc-light, temperature, and humidity sensor was fabricated on a flexible substrate using a printed thin film of indium tin oxide. A polyethylene terephthalate (PET) substrate was used as the flexible substrate. The sensor was fabricated on a PET substrate, and its operating characteristics were tested. The operating performances of the sensor when serving as an arc-light, a temperature, and a humidity sensor were estimated to be 0.6247 Ω/W, 80.6 Ω/K, and -4.08 Ω/RH, respectively. The feasibility of the proposed fire sensor was demonstrated; it costs low and offers multiple functionalities.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.10
• /
• pp.2597-2605
• /
• 1994

The wear behavior of two types of $Si_3N_4$ exposed to high and low humidity was examined at various sliding speeds, using bearing steel as disk material under pin-on-disk type sliding conditions. Higher wear rates were obtained at a high humidity than at a low humidity. As the sliding speed was increased, the wear rates were decreased and the effect of humidity on the wear rates of $Si_3N_4$ was reduced. The result that the $Si_3N_4$ pin showed higher wear rate under the high humidity condition was explained by the decrease in microhardness of $Si_3N_4$ due to the chemisorbed moisture on the pin and plowing action by the hard particles of $Fe_2O_3$ from the disk. An increase in the sliding speed is supposed to reduce the effect of humidity on the wear rate of $Si_3N_4$ by raising the average temperature of the disk surface and the local temperature at pin-disk contact point.

• The Journal of Engineering Geology
• /
• v.5 no.1
• /
• pp.21-29
• /
• 1995

Among the index properties of granite and andesite, the relation between porosity and water content is highly correlated, but specific gravity, porosity and water content have loW relation with P wave velocity and their relationship showed dispersed zone type. With raising the temperature, Brazilian tensile strength was not changed remarkably, but decreased near $100^{\circ}C$. After the strength increased at $150^{\circ}C$, it decreased near $200^{\circ}C$ in granite. In andesite, however, the strength was increased up to $200^{\circ}C$, and then decreased. The variations of P wave velocity at each temperature zone are similar to those of tensile strength.

• New & Renewable Energy
• /
• v.2 no.4 s.8
• /
• pp.70-77
• /
• 2006

The butane decomposition over the catalyst is an attractive method for the hydrogen production. The objective of the work was investigated the catalysis of carbon black in butane decomposition reaction. The Butane decomposition was performed over carbon black catalyst in a range of $500-1100^{\circ}C$. The butane conversion of thermal decomposition and catalytic decomposition were increased with increasing the reaction temperature The butane conversion of the thermal decomposition was higher than the butane conversion of the catalytic decomposition. Hydrogen and methane were mostly observed in the butane decomposition over $1000^{\circ}C$. Especially, the hydrogen yield was steadily increased with raising the reaction temperature, It could be known that the hydrogen yield of the catalytic decomposition was higher than one of the thermal cracking because the hydrogen productivity was improved by the catalyst. The deactivation of the catalyst was not observed in the reactivity test. The surface and crystalline of the fresh and used catalysts were characterized by TEM, BET surface area and XRD analysis, respectively. The fresh carbon black particles had mostly smoothly round-shaped surfaces. In the surface of the carbon black after the reaction, the deposited carbon was formed as the protrusion-shaped carbon and the cone-shaped. The proper peaks of carbon black appeared in XRD analysis.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.177-186
• /
• 2011

We can expect reduction of the sunlight absorption quantity to a structure and an earth surface, a decline of the surface temperature and a decline of the heat transport volume in what there is a method I give the sunlight reflectance in the aspect to the surface of the building by painting sunlight high reflectance paint, and to reduce the sunlight absorption quantity to a structure and an earth surface and does so, and, in addition, a method high water retentivity of tree planting and the road surface of the city space uses evaporation latent heat of the water by making it, and to restrain a rise in temperature is thought about. and It is thought that I reduce the sunlight absorption quantity to not only the structure but also other structures and attention gathers to the reflexive reflector reflecting in the direction again and it is wide as a marker of a board and the clothing of the traffic sign and is used the incidence energy from a source of light for this reflexive reflector now by there is it and devises surface structure again, and controlling reflection directivity for the sunlight for the purpose of raising night visibility.

• Journal of the Korean Chemical Society
• /
• v.25 no.2
• /
• pp.92-96
• /
• 1981

The reactions of adsorbed oxygen species, $O_2^-$ and $O^-$, with propylene on ZnO were studied by EPR spectroscopy and temperature programmed desorption technique. Propylene interacts with adsorbed $O_2^-$ at $25^{\circ}C$ and the surface intermediate was decomposed to CO, $H_2$, $CO_2$ and $CH_4$ by raising the temperature above $200^{\circ}C$, while $O^-$ gave the products of complete oxidation, $CO_2$ and $H_2O$ above $300^{\circ}C$.