• Journal of the Korean Society of Mechanical Technology
• /
• v.20 no.6
• /
• pp.924-928
• /
• 2018

The objective of this study is to solve a problem that is occurred during the spline machining of tubular shaft yoke in both side IMS module. In order to simulate the problem, the movement direction of upper die was set as standard case and error case. The material of tubular shaft yoke was set to S20C as refer to the analysis library. The movement directions of upper die were separated with standard case and error case. The error case was set to simulate the problem in the spline machining of tubular shaft yoke. In order to solve the problem, the outer radius of upper die were modelled from 9.40mm to 9.44mm. The simulation results were analyzed and compared in terms of effective stress, metal flow line and folding phenomena characteristics. In case of the outer radius of upper die was 9.42mm, it was observed a relatively uniform effective stress distribution and had a straight metal flow line.

• 한국환경농학회:학술대회논문집
• /
• 2009.07a
• /
• pp.220-227
• /
• 2009

For last about 10 years, the Republic of Korea experienced 3 times of outbreaks of highly pathogenic avian influenza (HPAI) from 10 December 2003 to 30 April 2004 (a total number of 19 outbreaks), 22 November 2006 to 6 March 2007 (a total number of 7 outbreaks), and 1 April 2008 to 12 May 2008 (a total number of 33 outbreaks). Among the totally 59 outbreaks, the infected premises included 35 chicken farms, 17 duck farms, 1 quail farm, and 6 farms rearing mixed species. Control measures were applied according to the HPAI standard operation procedure including depopulation of all infected and suspected flocks, movement restrictions, and disinfection of the infected farms within a 500-meter radius. Including movement restrictions, stringent control measures were additionally applied to two designated zones: the protection zone was an area within a 3-kilometer radius of the outbreak farm, and the surveillance zone was an area between a 3- to 10-kilometer radius of the outbreak farm. Farms with dangerous contacts and/or all of poultry within the protection zone was subjected to preemptive culling. Epidemiological investigations were also carried out including trace-back and trace-forward investigations to identify possible sources of spread and dangerous contact farms. Investigation teams conducted on-site examination of farm premises and facilities, interview with farm owner and staff, and review of records. Genetic and pathogenic characteristics of the virus isolates, and the results of the various surveillance activities were also analyzed. HPAI surveillance conducted in Korea includes passive surveillance of investigating notified cases, and active surveillance of testing high risk groups and areas. HPAI is a notifiable disease in Korea and all suspect cases must be reported to the veterinary authorities. Cases reported for other poultry diseases that require differential diagnosis are also tested for HPAI. Active surveillance includes annual testing of breeder duck farms, broiler duck farms and wild bird surveillance, which is concentrated during the autumn and winter. Surveillance activities conducted prior to the outbreaks have shown no evidence of HPAI infection in Korea.

• Fisheries and Aquatic Sciences
• /
• v.9 no.2
• /
• pp.91-96
• /
• 2006

The movement range and diurnal behavior of 17 wild black rockfish (Sebastes schlegeli) were monitored within the marine ranching area of Tongyeong from 27 July to 7 November, 2005 using acoustic telemetry. Coded transmitters were surgically implanted into the abdomen of fish. Two of ten fish released in summer moved about 2 km away from the capture point for 1 day. The others stayed within a 500-m radius of the release point for 1 week after release. The seven fish released in autumn stayed within 500 m of the release point. Most fish were more active and had a greater range of horizontal diurnal movement at night than during the day. Additionally, the range of horizontal diurnal variation was greater in summer than in autumn. While fish released in summer were more vertically active at night than during the day, those released in autumn preferred to move vertically during the day.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.979-983
• /
• 2010

In case a set of railway vehicles moves on a rail track, the end of each car in which a coupler is installed produces a complex movement depending on the displacement of a rail track, bogie and a coupler. Especially, the movement of an end of cars is hugely affected by a radius of gyration and gradient of a rail track, vertical and lateral movement of bogie, and compression of coupler. In this thesis, I present a simulation technic for easy input and change of displacement of a rail track, bogie and a coupler as well as visualization of movement of the end of cars on a rail track using CATIA V5, CAD software.

• Journal of Life Science
• /
• v.16 no.5
• /
• pp.773-779
• /
• 2006

Eight of the individuals had a unilateral S-RAD TKA and Multi-Radius TKA ($Scorpio^{TM}$ PS, Howmedica-Osteonics, Inc.). The instrument were used Peak Motion Measurement $System^{TM}$, $MYOPAC^{TM}$EMG System, KIN-COM $III^{TM}$ System. The Figure 3 shows that the average time for the S-RAD group to accomplish the sit-to-stand movement was 1.59 s, which was 0.19 s less than the M-RAD group (p= 0.033). In Figure 5, the S-RAD TKA group tended to have $7^{\Omega}{\cdot}S^{-1}$ less trunk flexion velocity than that of the M-RAD group (p= 0.058). The Figure 6 shows that the S-RAD TKA limb tended to have less ADD displacement (p = 0.071) than that of the M-RAD TKA limb. We failed to find significant differences for ABD and ADD displacements between the S-RAD and M-RAD N-TKA limbs (p= 0.128 and 0.457, respectively). The VM of the S-RAD TKA limb demonstrated significant less RMS EMG than that of the M-RAD TKA limb from $60^{\Omega}$ to $15^{\Omega}$ of knee flexion (p 0.05). The VL of the S-RAD TKA limb also demonstrated significant less RMS EMG than that of the M-RAD TKA limb from $60^{\Omega}$ to $45^{\Omega}$ of knee flexion (p 0.05). Similar to the VM and VL, the RF of the S-RAD TKA limb showed less RMS EMG than that of the M-RAD TKA limb from $60^{\Omega}$ to $30^{\Omega}$ of knee flexion (p 0.05).

• Journal of Veterinary Clinics
• /
• v.20 no.3
• /
• pp.403-405
• /
• 2003

A 11 month-old Shihtzu was referred to the Veterinary Medical Teaching Hospital, Seoul National University. Clinical signs of this patient were lameness, shortening limb, angular deformity, rotation of foot, subluxaion of elbow joint and restricted range of movement of left forelimb. For the evaluation of the abnormalities of left forelimb, radiographic examination was carried out. Radiographic findings were characteristics of premature closure of distal ulna such as closure of distal ulna growth plate and cranial bowing of radius. With radiographic signs and physical examination, it was diagnosed as premature closure of growth plate of the left forelimb. After osteotomy of the radius and ostectomy of the ulna, radiographic evaluation of limb about angulation of elbow joint was performed every 2-3 weeks for 3 months. In case of premature closure of distal growth plate of ulna, radiography was very useful for diagnositic method of premature closure of distal ulna and monitoring of healing process.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.2
• /
• pp.382-390
• /
• 1995

Failure of connecting rod in automotive engine may cause catastrophic situation. The corner radius at small end has an effect on stress raising. To investigate the stress distribution in connecting rod during operation, the finite element analysis was used by giving possible maximum tension and compression. Excessive sizing after forging connecting rod may result in the tensile residual stress which lower the fatigue life and cause premature failures. It was shown that when the sizing amount is too large, the location of high tensile residual stress coincide with that of high stress amplitude during operation through the elastic-plastic finite element analysis. The endurance limit moves down due to the surface finish and decarburization, which combines with the movement of resultant stress points to dangerous range. It was concluded that the precise control of sizing and enough corner radius are necessary to a reliability of connecting rod.

• The Journal of Korean Academy of Prosthodontics
• /
• v.25 no.1
• /
• pp.119-135
• /
• 1987

For the determination of instantaneous centre of rotation in the mandibular movement, the habitual opening path was recorded on the sagittal tracing plate by a Gnathorecorder attached on the lower anterior teeth which was designed for this study. The opening path was demonstrated mathematically and the instantaneous centre of rotation in the opening path were calculated and plotted by computer programs, and then a computer graphic movement of the mandible was obtained according to the opening path. The hinge path of posterior border movement was graphied by the Gnathorecorder as well and demonstated mathematically. This hinge path was compared with the same obtained by Visitrainer to prove a reliability of the Gnathorecorder. The results obtained from this study were as follows. 1. The habitual opening path and hinge path obtained from the Gnathorecorder movement were expressed mathematically as follows: $y=0.11x^2-0.66x+3.09$ (equation of opening path), $y=0.04x^2+0.21x+3.71$ (equation of hinge path), and a kinematic hinge axis was not shown in the equation of kings path. 2. The early habitual opening movement of the mandible demonstrated almost a straight opening path or an arc motion with the larger radius and it's centre of rotation moved parallelly in the more rear and lower position than a kinematic hinge axis. 3. Instantaneous centre of rotation occured along with the translation of the condyle, and mandible was rotated around an axis in the close to the maximum opening and then moved toward the forward and upward position. 4. There were some similarities between the articular eminence and the movement pattern of a special point which was the kinematic hinge axis.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.786-791
• /
• 2000

The purpose of this study is to investigate quantitatively the effects of drawbead dimensions to the weld line movements for the deep drawing of the tailor welded blanks. Square blanks have been used and five different circular drawbeads were installed in experimental apparatus. The differences in the weld-line movements and the tendencies of the strain distributions in thickness were investigated by experimental and analytical methods. The results of the weldline movement show that the smaller the radius of drawbead installed, the larger the values of movements. Also it is shown for thickness strain in central and diagonal direction that the larger the dimension of drawbead, the larger the values of maximum thickness strain. The drawbead adds the additional restraining forces to the blank, hence the movement of weld line could be controlled by the adequate drawbead installation

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.54-65
• /
• 1993

The paper describes and alternative method based on a new idea to measure the circular movement of machining centers. ISO has employed three testing methods for the acceptance tests of machine tools; the first is a rotating one-dimensional probe method, the second is a two-dimensional probe and a master circular ring, and the third is a kinematic ball bar. The last two methods were proposed and introduced by W. Knapp and J. B. Bryan, respectively. The newly developed method is superior to above two methods; the rotating angle can be detected and the rotating radius is variable. Circular movement errors of machining centers were investigated by the analysis of data measured by R- .THETA. method. Followint observations are obtained 1) The errors which depend on positions, i.e., periodical errors by the pitch of ball screws, errors by compensation of backlash and errors by perpendicularity of X and Y-axis, were analyzed. 2) The errors which depend on NC control system, i.e., errors by the unbalance of position-loop-gaians, errors by velocity-loop-gains and errors by feed speeds, were quantiatively analyzed. 3) The method of extracting error information, which uses moving technique of averaging angle and fourier's analysis data mesured by the R- .THETA. method, was proposed.