• 한국세라믹학회지
• /
• 제30권6호
• /
• pp.510-516
• /
• 1993

$PbTiO_3$ thin films have been formed by rapid thermal annealing(RTA) of $TiO_2$/Pb/$TiO_2$ multilayer films deposited on Si wafers by RF sputtering. Based on the optimal depositon conditions of TiO2 and Pb, $TiO_2$/Pb/$TiO_2$ three layers were deposited for 900$\AA$ each. These films were subjected to RTA process at the temperatures ranging from $400^{\circ}C$ to $900^{\circ}C$ for 30 seconds in air, and were analyzed by X-ray diffraction and transmission electron microscopy to investigate the phases and the microstructures. As a result, perovskite $PbTiO_3$ phases was obtained above $500^{\circ}C$ with the trace of unreacted $TiO_2$. RBS analysis revealed the anisotropic behavior of diffusion that the diffusivity of Pb to the bottom $TiO_2$ layer was faster than that of Pb to the top $TiO_2$ layer. The amorphous Pb-silicate was formed between film and Si substrate due to the diffusion of Pb, but Pb-silicate existed locally at the interface and the amount of that phase was very small. Therefore the effect of bottom $TiO_2$ layer as a diffusion barrier was confirmed. $PbTiO_3$ films formed by current technique showed a relative dielectric constant of 60, and the maximum breakdown field reached 170kV/cm.

• 한국재료학회지
• /
• 제11권9호
• /
• pp.776-780
• /
• 2001

$SiO_2$ and polycrystalline Si layers were sequentially grown on (100) Si. NiSi was formed on this substrate from a 20nm Ni layer or a 20nm Ni/5nm Ti bilayer by rapid thermal annealing (RTA) at $300~500^{\circ}C$ to compare thermal stability. In addition, MOS capacitors were fabricated by depositing a 20nm Ni layer on the Poly-Si/$SiO_2$substrate, RTA at $400^{\circ}C$ to form NiSi, $BF_2$ or As implantation and finally drive- in annealing at $500~800^{\circ}C$ to evaluate electrical characteristics. When annealed at $400^{\circ}C$, NiSi made from both a Ni monolayer and a Ni/Ti bilayer showed excellent thermal stability. But NiSi made from a Ni/Ti bilayer was thermally unstable at $500^{\circ}C$. This was attributed to the formation of insignificantly small amount of NiSi due to suppressed Ni diffusion through the Ti layer. PMOS and NMOS capacitors made by using a Ni monolayer and the SADS(silicide as a dopant source) method showed good C-V characteristics, when drive-in annealed at $500^{\circ}C$ for 20sec., and$ 600^{\circ}C$ for 80sec. respectively.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권4호
• /
• pp.232-238
• /
• 2000

PZT thin films(3500 ) have been prepared onto $Pt/Ti/SiO_2/Si$ substrates with a RF magnetron sputtering system using PB1.05(Zr0.52,Ti0.48)O3 ceramic target. We used two-step annealing techniques. As the RTA times and temperatures were increased, crystallization of PZT thin films were enhanced. The ferroelectric characteristics of PZT capacitors fabricated at $700^{\circ}C$ for 60 seconds were like these remanent polarization were $12.1 \muC/cm^2$, coercive field were 110 kV/cm, leakage current density were $4.1\times10-7 A/cm^2,\; \varepsilonr=442,$ and remanent polarization were decreased by 22% after 1010 cycles, respectively.

• 한국전기전자재료학회논문지
• /
• 제13권4호
• /
• pp.312-317
• /
• 2000

Ferroelectric S $r_{0.9}$/B $i_{2.1}$/T $a_{2}$/ $O_{9}$ solutions were synthesized using sol-gel process in which strontinum ethoxide bismuth ethoxide trantalum ethoxide were used a s startring materials. SBT thin films were coated on Pt/Ti/ $SiO_2$/Si substrates by spin-coating. rapid thermal annealing (RTA) was used to promote crystallization. Thin films were annealed at $700^{\circ}C$ for 1 hr in an oxygen atmosphere. This temperature is about 10$0^{\circ}C$ lower than the usual annealing temperature for SBT thin films. Pt top-electrode was deposited by sputtering and thin films were post-annealed at $700^{\circ}C$ for 30 min. to enhance electrical properties. As the RTA temperature increased the higher 2 $P_{r}$ values were obtained. At RTA temperature being 78$0^{\circ}C$ remanent polarization of S $r_{0.9}$/B $i_{2.1}$/T $a_{2}$/ $O_{9}$ thin film was 7.73 $\mu$C/cm $_2$ and the leakage current density was 1.14$\times$10$^{-7}$ A/c $m^2$ at 3 V. As RTA temperature increased the breakdown voltage was decreased. It is considered that the low-field breadown is caused by the rough surface of SBT films and forming bismuth metal in SBT thin films.films.lms.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.51-54
• /
• 2000

In this paper, $Ba_{0.5}$Sr$_{0.5}$TiO$_3$ thin films were prepared on Pt/Ti/SiO$_2$/Si substrate by RF magnetron sputtering method. We investigated effect of deposition conditions (especially RF input power) on structural properties of BST thin films. Deposit conditions of BST films were set working gas ratio, Ar:O$_2$= 70 : 30, working pressure 10mTorr, and RF input power 25W, 50W, 75W and 100W. Post-annealing using rapid thermal annealing(RTA) performed at 45$0^{\circ}C$, 55$0^{\circ}C$, $650^{\circ}C$, and 75$0^{\circ}C$ in oxigen ambient for 60 sec, respectively. The structural properties of BST films on Pt/Ti/SiO$_2$/Si substrate analysed by X-ray diffraction(XRD).).).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.687-690
• /
• 2004

Fabrication and characterization of dye-sensitized TiO2 solar cells(DSSC) consisting of spray-coated TiO2 electrode, an electrolyte containing I-/I3- redox couple, and a Pt-coated counter electrode carried out, using mainly FE-SEM and solar simulator. Also, effect of rapid thermal annealing(RTA) temperatue on I-V curves of DSSCS consisting of approximately 10m thickness and $5{\times}5mm2$ active area. No significant difference in the apparent size of TiO2 clusters was observed with increasing RTA temperature. Also, an open circuit voltage(Voc) of approximately 0.70V and a short-circuit photocurrent(Jsc) of 8 to 12mA/cm2 were observed in the TiO2 solar cell. With increasing RTA temperature upto 550oC, photocurrent density of dye-sensitized solar cells was enhanced, leading to enhancing the efficiency of dye-sensitized solar cells having Pt-electroplated counter electrode.

• Transactions on Electrical and Electronic Materials
• /
• 제6권2호
• /
• pp.51-56
• /
• 2005

Ferroelectric Bi$_{3.35}$Sm$_{0.65}$Ti$_{3}$O$_{12}$(BSmT) thin films were synthesized using a sol-gel process. Bi(TMHD)$_{3}$, Sm$_{5}$(O$^{i}$Pr)13, Ti(O$^{i}$Pr)4 were used as the precursors, which were dissolved in 2­methoxyethanol. The BSmT thin films were deposited on Pt/TiO$_{x}$/SiO$_{2}$/Si substrates by spin­coating. The electrical properties of the thin films were enhanced using rapid thermal annealing process (RTA) at 600 $^{circ}$C for 1 min in O$_{2}$. Thereafter, the thin films were annealed from 600 to 720 $^{circ}$C in oxygen ambient for 1 hr, which was followed by post-annealed for 1 hr after depositing a Pt electrode to enhance the electrical properties. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to analyze the crystallinity and surface morphology of layered perovskite phase, respectively. The remanent polarization value of the BSmT thin films annealed at 720 $^{circ}$C after the RTA treatment was 35.31 $\mu$C/cmz at an applied voltage of 5 V.

• 한국진공학회지
• /
• 제11권1호
• /
• pp.1-7
• /
• 2002

RF Magnetron Sputtering 방법으로 $Ba_{0.5}Sr_{0.5}TiO_3$ 박막을 Pt/Ti/$SiO_2$/Si 기판위에 증착하였다. $Ba_{0.5}Sr_{0.5}TiO_3$ 박막 증착시 기판온도는 실온으로 고정시켜주었고, 작업 가스 유량(Ar:$O_2$)과 RF Power는 각각 90:10에서 60:40까지 그리고 50 W와 75 W로 하였다. 또한 박막 증착 후 RTA(Rapid Thermal Annealing)를 이용하여 산소분위기에서 $600^{\circ}C$로 고온 순간 열처리를 하였다. 커패시터 제작을 위해 UHV System의 E-beam evaporator를 이용하여 Pt를 증착하였다. XRD 측정을 통한 구조적 특성에서는 작업 가스 유량과 RF Power에 비해 고온 순간 열처리가 결정화에 기여도가 큼을 확인할 수 있었다. 전기적 특성에서는 RF Power가 50 W이고 열처리를 한 샘플에서 비교적 우수한 특성을 보여주었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.80-83
• /
• 2000

The post-annealing treatments on rf magnetron sputtered PZT($Pb_{1.05}(Zr_{0.52},\;Ti_{0.48})O_3$) thin films($4000{\AA}$) have been investigated for a structure of PZT/Pt/Ti/Coming glass(1737). Crystallization properties of PZT films were strongly dependent on RTA(Rapid Thermal Annealing) annealing temperature and time. We were able to obtain a perovskite structure of PZT at $650^{\circ}C$ and 10min. P-E curves of Pd/PZT/Pt capacitor demonstrate typical hysteresis loops. The measured values of $P_r$, $E_c$ were $8.1[{\mu}C/cm^2]$, 95[kV/cm] respectively. Polarization value decrease about 25% after $10^9$ cycles.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.197-197
• /
• 2010

본 연구에서는 RF/DC dual 마그네트론 스퍼터 시스템을 이용하여 Glass 기판 상에 유기태양전지용 Nb-doped $TiO_2$ (NTO)/Ag/NTO 다층 투명전극을 성막하고 이 다층 투명전극을 $200^{\circ}C{\sim}700^{\circ}C$ 온도 범위에서 급속 열처리 (Rapid Thermal Annealing ; RTA)를 통하여 전기적, 광학적, 구조적 및 표면의 특성 변화를 연구하였다. Hall effect measurement, UV-Vis spectrometer, FESEM 분석을 통하여 다층투명전극의 전기적, 광학적, 표면분석을 하였고 Synchrotron 분석을 통하여 온도에 따른 구조변화를 분석하였다. 상온에서 성막된 다층투명전극은 30nm 두께의 NTO 박막 사이에 얇은 9nm의 얇은 Ag 층을 삽입한 구조로써 10ohm/square 이하의 매우 낮은 면저항과 ${\sim}10^{-5}\;ohm-cm$ 의 비저항, Anti-reflection 효과에 의해 85% 이상의 높은 광투과성을 나타내었다. RTA 온도가 증가함에 따라 전기적, 광학적 특성은 약간 향상되었고 비정질 구조를 유지함을 알 수 있었다. 그러나 높은 온도범위에서는 비정질 구조에서 Anatase 상으로 결정구조가 변화함을 알 수 있었고 전기적, 광학적 특성이 감소됨을 알 수 있었다. NTO/Ag/NTO 다층 투명전극을 유기태양전의 Anode로 적용하여 특성을 비교한 결과 RTA 온도가 증가함에 따라 유기태양전지의 효율 또한 증가하였고 최적화된 온도 조건에서 2.49% 의 높은 효율을 얻을 수 있었다. 이를 통해 우수한 특성을 나타내는 NTO/Ag/NTO 다층투명전극이 기존의 디스플레이 및 태양전지 등의 투명전극 재료로 주로 사용되어 온 ITO (Indium Tin Oxide) 를 대체 할 수 있는 재료로써의 가능성을 제시하였다.