• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.2
• /
• pp.178-182
• /
• 2011

A FSK receiver RF block has been developed for Dubaisat-1 Low Earth Orbit satellite. The receiver has Doppler tracking function which compensate frequency shift on uplink channel for commanding the satellite. It consist of LNA, downconverter and IF module. The IF module has Doppler tracking circuitry which sweep and lock on to input signal. It satisfies the requirement of the Dubaisat-1 in mass, power consumption, tracking speed and BER performance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.7
• /
• pp.500-507
• /
• 2018

A three-channel radio frequency (RF) monopulse receiver using a data signal with a maximum transmission rate of 274 Mbps was designed. A monopulse receiver using a broadband communication signal was designed to operate in the Ku band, and it consists of a down-conversion module and a signal-processing module. To satisfy the performance of the proposed RF monopulse receiver, a signal-processing function less than the reception sensitivity for each transmission rate according to the adaptive transmission rate is required. To minimize signal reception and mutual frequency interference of various bandwidths, two RF filters were applied. To verify the satisfaction of system requirements, an AWR Corp. simulation tool was used.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.3
• /
• pp.282-288
• /
• 2014

In this paper, we have analyzed and designed a digital RF receiver based on the optimization of the dynamic range parameter to secure the wideband characteristics and linearity of digital radar receivers. To improve the wideband characteristics and dynamic range, a low noise amplifier is matching design with a noise source to minimize the noise figure in 1 GHz bandwidth and we improved the linearity of RF-receiver by securing the conversion gain characteristics of receiver through the design of active mixer. RF receiver is designed to give gain 63 dB, noise figure 1.2 dB and dynamic range of RF receiver has 75.8 dB in a wide band of 8.8~9.8 GHz. It is shown to be applicable to X-band digital radar receiver.

• Journal of Satellite, Information and Communications
• /
• v.2 no.2
• /
• pp.64-68
• /
• 2007

This paper describes the development of RF front.end equipment of a wide band high precision satellite navigation receiver to be able to receive the currently available GPS navigation signal and the GALILEO navigation signal to be developed in Europe in the near future. The wide band satellite navigation receiver with high precision performance is composed of L - band antenna, RF/IF converters for multi - band navigation signals, and high performance baseband processor. The L - band satellite navigation antenna is able to be received the signals in the range from 1.1 GHz to 1.6 GHz and from the navigation satellite positioned near the horizon. The navigation signal of GALILEO navigation satellite consists of L1, E5, and E6 band with signal bandwidth more than 20 MHz which is wider than GPS signal. Due to the wide band navigation signal, the IF frequency and signal processing speed should be increased. The RF/IF converter has been designed with the single stage downconversion structure, and the IF frequency of 140 MHz has been derived from considering the maximum signal bandwidth and the sampling frequency of 112 MHz to be used in ADC circuit. The final output of RF/IF converter is a digital IF signal which is generated from signal processing of the AD converter from the IF signal. The developed RF front - end has the C/N0 performance over 40dB - Hz for the - 130dBm input signal power and includes the automatic gain control circuits to provide the dynamic range over 40dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.5A
• /
• pp.496-503
• /
• 2010

The implementation of a RF transceiver for WRAN(Wireless Regional Area Network) system based on IEEE 802.22 standard using Cognitive Radio technology is presented in this paper. A CMOS RF transceiver IC for WRAN system operates in VHF/UHF(54~862MHz) broadband, and employs dual-path direct-conversion configuration and the in-band harmonic distortions are effectively suppressed by exploiting the dual-path direct conversion architecture. For 64QAM(3/4 coding rate) OFDM signal, an EVM of <-31.4dB(2.7%) has been achieved at 10dBm off-chip PA output power and the total chip area with pads is 12.95 mm2. The experimental results show that the proposed CMOS RF transceiver IC has perfect performance for WRAN system based on TDD(Time Division Duplex) mode.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.6
• /
• pp.600-613
• /
• 1997

The implementation of a BTS(Base station Transceiver) for WLL system using W-CDMA(Wideband-Code Division Multiple Access) method is presented in this paper. It consists of three boards; receiver, transmitter and RF controller. Some RF parameters are considered and simulated by the RF simulation S/W using commercial and customized components specifications. The implemented transceiver of 5 MHz RF channel bandwidth satisfies the system requirements of a transceiver such as dynamic range, sensitivity in the receiver and spurious emission suppression in the transmitter. At the receiver, the experimental measurement showed 2.86 dB of NF and 60 dB above of dynamic range in AGC(Automatic Gain Control) locking. At the transmitter, the -49.46 dBc of spurious emission suppression is attained when the output power of the transmitter is 34.3 dBm. These results are good enough to meet to standard performance specifications.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.1
• /
• pp.91-99
• /
• 2018

This paper has proposed a low-noise and high-linear RF receiver supporting TV white space from 470 MHz to 698 MHz), which is implemented in $0.13-{\mu}m$ CMOS technology. It consists of a low-noise amplifier, a RF band-pass filter, a RF amplifier, a passive down-conversion mixer, and a channel-selection low-pass filter. A low-noise amplifier and RF amplifier provide a high voltage gain to improve the sensitivity level. To suppress strong and nearby interferers, two RF filtering schemes have been performed by using a RF BPF and a down-conversion mixer. The proposed LPF has been based on the common-gate topology and adopted a bi-quad cell to achieve -24dB/oct characteristics. In addition, the RF receiver can support the overall TV band by controlling a LO frequency. The simulated results show a voltage gain of 56 dB, a noise figure of less than 2 dB, and an out-of-channel IIP3 of -2.3 dBm. It consumes 37 mA from a 1.5 V supply voltage.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.11
• /
• pp.1130-1137
• /
• 2009

This paper proposes a new clock routing design for suppressing clock harmonic effects in a Printed Circuit Board (PCB) for a terrestrial Digital Multimedia Broadcasting(DMB) system. Typical crystal reference frequencies that are widely used in DMB tuners are 16.384 MHz, 19.2 MHz, 24.576 MHz. When the high-order harmonic components of these reference frequencies fall near the RF channel frequencies, receiver sensitivity of the tuners is seriously degraded. In this work, we propose a new clock routing design in order to address the clock harmonic coupling issue. The proposed design incorporates two inductors for isolating the clock ground from the main ground, and adopts a new strip line-style routing instead of the conventional microstrip line style routing to minimize the overlap area with the main ground. As a result, the RF sensitivity of the T-DMB tuner is improved by 2 dB.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.2
• /
• pp.36-44
• /
• 2016

In this paper, an Impulse Radio-Ultra Wide band RF Transceiver for WBAN applications is implemented in $0.18{\mu}m$ CMOS technology. The designed RF transceiver support 3-5GHz UWB low band and employs OOK(On-Off Keying) modulation. The receiver employs non-coherent energy detection architecture to reduce complexity and power consumption. For the rejection of the undesired interferers and improvement of the receiver sensitivity, RF active notch filter is integrated. The VCO based transmitter employs the switch mechanism. As adapt the switch mechanism, power consumption and VCO leakage can be reduced. Also, the spectrum mask is always same at each center frequency. The measured sensitivity of the receiver is -84.1 dBm at 3.5 GHz with 1.579 Mbps. The power consumption of the transmitter and receiver are 0.3nJ/bit and 41 mW respectively.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.3
• /
• pp.212-217
• /
• 2016

The S-band receiver for Low Earth Orbit satellite is designed and fabricated as engineering model. Demodulator is implemented by using FPGA for extension of demodulator method. The receiver consists of RF Block, Digital demodulator and Power stage and has a Doppler tracking function to compensate a frequency shift that occur on the operation. The measured results of fabricated receiver show BER of less than $1.0{\times}10^{-6}$ at -110dBm RF input power and equipped a frequency tracking of ${\pm}100KHz$ relative to the center frequency. TID test was satisfied with the results of the test criterion is 10krad.