• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.1
• /
• pp.6-10
• /
• 2007

The a-plane GaN layer on r-plane $Al_2O_3$ substrate is grown by mixed-source hydride vapor phase epitaxy (HVPE). The GaN/InGaN heterostructure is performed by selective area growth (SAG) method. The heterostructure consists of a flown over mixed-sourec are used as gallium (or indium) and nitrogen sources. The gas flow rates of HCl and $NH_3$ are maintained at 10 sccm and 500 sccm, respectively. The temperatures of GaN source zone is $650^{\circ}C$. In case of InGaN, the temperature of source zone is $900^{\circ}C$. The grown temperatures of GaN and InGaN layer are $820^{\circ}C\;and\;850^{\circ}C$, respectively. The EL (electroluminescence) peak of GaN/InGaN heterostructure is at nearly 460 nm and the FWHM (full width at half maximum) is 0.67 eV. These results are demonstrated that the heterostructure of III-nitrides on r-plane sapphire can be successfully grown by mixed-source HVPE with multi-sliding boat system.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.2
• /
• pp.56-61
• /
• 2015

The effects of the growth temperature on the properties of a-plane GaN epi-layer on r-plane sapphire by HVPE were studied, when the constant V/III ratio and the flow rate of HCl for the Ga source channel was fixed at 10 and 700 sccm, respectively. Additionally the effects of V/III ratios for source gasses were studied when growth temperature and the flow rate of HCl for the Ga source channel was fixed at $1000^{\circ}C$ and 700 sccm, respectively. As the growth temperature was increased, the values of Full Width Half Maximum (FWHM) for Rocking curve (RC) of a-plane GaN (11-20) epi-layer were decreased and thickness of a-plane GaN epi-layer were increased. As V/III ratios were increased at $1000^{\circ}C$, the values of FWHM for RC of a-plane GaN (11-20) were declined and thickness of a-plane GaN epi-layer were increased. The a-plane GaN (11-20) epi-layer grown at $1000^{\circ}C$ and V/III ratio = 10 showed the lowest value FWHM for RC of a-plane GaN (11-20) for 734 arcsec and the smallest dependence of Azimuth angle for FWHM of (11-20) RCs.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.27.1-27.1
• /
• 2009

In recent years, ZnO nanostructures have drawn considerable attentions for the development of futuristic electronic devices due to their superior structural and optical properties. As the growth of ZnO nanowires by MOCVD is a bottom-up technique, the nature of substrates has a vital role for the dimension and alignment of the nanowires. However, in the pursuit of next generation ZnO based nanodevices, it would be highly preferred if well-ordered ZnO nanowires could be obtained on various substrates like sapphire, silicon, glass etc. Vertically aligned nanowires were grown on A and C-plane sapphire substrates, where as nanopencils were obtained on R-plane sapphire substrates. In addition, C-axis oriented vertical nanowires were also found using an interfacial layer(aluminum nitride film) on silicon substrates. On the other hand, long nanowires were found on Ga-doped ZnO film on glass substrates. Structural and optical properties of the ZnO nanowires on various substrates were also investigated.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.88-91
• /
• 2003

The crystal structure and properties of YBa$_2$Cu$_3$$O_{7-x}$(YBCO) and CeO$_2$ thin films deposited on r-plane (1(equation omitted)02) sapphire substrate by pulsed- laser deposition(PLD) have been investigated. C-axis oriented epitaxial YBCO thin films with critical temperature (Tc) of 88 K were routinely grown on (200) oriented CeO$_2$ buffer layers with thickness in the range between 20 to 80 nm. When the thickness of the (200)oriented CeO$_2$ buffer layer increases over than 80 nm, the superconducting properties of YBCO thin films on that were deteriorated. The decrease in Tc of YBCO thin films was explained by the microcrack formation in CeO$_2$ buffer layer. These results indicate that the thickness of the (200) oriented CeO$_2$ buffer layer is critical to the epitaxial YBCO thin nim growth on r-plane (1(equation omitted)02) sapphire substrate.e.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.1
• /
• pp.6-10
• /
• 2009

In this paper, a selective area growth (SAG) of a GaN/AlGaN double heterostructure (DH) has been performed on r-plane sapphire substrate by using the mixed-source hydride vapor phase epitaxy (HVPE) with multi-sliding boat system. The SAG-GaN/AlGaN DH consists of GaN buffer layer, Te-doped AlGaN n-cladding layer, GaN active layer, Mg-doped AlGaN p-cladding layer, and Mg-doped GaN p-capping layer. The electroluminescence (EL) characteristics show an emission peak of wavelength, 439 nm with a full width at half maximum (FWHM) of approximately 0.64 eV at 20 mA. The I-V measurements show that the turn-on voltage of the SAG-GaN/AlGaN DH is 3.4 V at room temperature. We found that the mixed-source HVPE method with a multi-sliding boat system was one of promising growth methods for III-Nitride LEDs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.114-114
• /
• 2009

ZnO has received considerable attention due to its potential applicability to optoelectronic devices such as ultraviolet-light emitting diodes (UVLEDs) and laser diodes (LDs). As well known, however, polar ZnO with the growth direction along the c-axis has spontaneous and piezoelectric polarizations that will result in decreased quantum efficiency. Recently, nonpolar ZnO has been studied to avoid such a polarization effect. In order to realize applications of nonpoar ZnO-based films to LEDs, growth of high quality alloys for quantum well structures is one of the important tasks that should be solved. $Mg_xZn_{1-x}O$ and $Cd_xZn_{1-x}O$ is ones of most promising alloys for this application because the alloys of ZnO with MgO and CdO provide a wide range of band-gap engineering spanning from 2.4 to 7.8 eV. In this study, we investigated on $Mg_xZn_{1-x}O$ films grown with various Mg/Zn flux ratios The films were grown on R-plane sapphire substrates by plasma-assisted molecular beam epitaxy (PAMBE). we investigated on $Mg_xZn_{1-x}O$ films grown with various Mg/Zn flux ratios. The films were grown on R-plane sapphire substrates by plasma-assisted molecular beam epitaxy (PAMBE). With the relatively low Mg/Zn flux ratios, a typical striated anisotropic surface morphology which was generally observed from the nonpolar (11-20) ZnO film on r-plane sapphire substrates. By increasing the Mg/Zn flux ratio, however, additional islands were appeared on the surface and finally the surface morphology was entirely changed, which was generally observed for the (0001) polar ZnO films by losing the striated morphology. Investigations by X-ray $\Theta-2{\Theta}$ diffraction revealed that (0002) and (10-11) ZnO planes are appeared in $Mg_xZn_{1-x}O$ films by increasing the Mg/Zn flux ratio. Further detailed investigation by transmission electron microscopy (TEM) and photoluminescence (PL) will be discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.147-147
• /
• 2011

High crystalline nonpolar a-plane (11-20) nitride light emitting diodes (LEDs) have been fabricated on r-plane (1-102) sapphire substrates by metalorganic chemical-vapor deposition (MOCVD). The multi-quantum wells (MQWs) active region is consists of 4 periods the nonpolar a-plane InGaN/GaN(a-InGaN/GaN) on a high quality a-plane GaN (a-GaN) template grown by using the multibuffer layer technique. The full widths at half maximum (FWHMs) of x-ray rocking curve (XRC) obtained from phiscan of the specimen that was grown up to nonpolar a-plane GaN LED layers with double crystal x-ray diffraction. The FWHM values were decreased down to 477 arc sec for $0^{\circ}$ and 505 arc sec for $-90^{\circ}$, respectively. After fabricating a conventional lateral LED chip which size was $300{\times}600{\mu}m^2$, we measured the optical output power by on-wafer measurements. N-electrode was made with Cr/Au contact, and ITO on p-GaN was formed with Ohmic contact using Ni/Au followed by inductively coupled plasma etching for mesa isolation. The optical output power of 1.08 mW was obtained at drive current of 20 mA with the peak emission wavelength of 502 nm.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.20.2-20.2
• /
• 2011

III-nitrides have attracted much attention for optoelectronic device applications whose emission wavelengths ranging from green to ultraviolet due to their wide band gap. However, due to the strong polarization properties of conventional c-plane III-nitrides, the built-in polarization-induced electric field limits the performance of optical devices. Therefore, there has been a renewed interest in the growth of nonpolar III-nitride semiconductors for polarization free heterostructure optoelectronic and electronic devices. However, the crystal and the optical quality of nonpolar/semipolar GaN have been poorer than those of conventional c-plane GaN, resulting in the relative poor optical and electrical properties of light emitting diodes (LEDs). In this presentation, I will discuss the growth and characterization of high quality nonpolar a-plane and semipolar (11-22) GaN and InGaN multiple quantum wells (MQWs) grown on r- and m-plane sapphire substrates, respectively, by using metalorganic chemical vapor deposition (MOCVD) without a low temperature GaN buffer layer. Especially, the epitaxial lateral overgrowth (ELO) technique will be also discussed to reduce the dislocation density and enhance the performance of nonpolar and semipolar GaN-based LEDs.

• Journal of the Korean Chemical Society
• /
• v.39 no.1
• /
• pp.1-6
• /
• 1995

The surface of a sapphire substrate used for hetero-epitaxy was chemically polished in a mixture of $H_3PO_4\;and\;H_2SO_4$ solution. The extent of etching for various crystal orientations was found to be dependent on the etching time at $315{\pm}2^{\circ}C$ and at the composition of $H_2SO_4 : H_3PO_4$=3 : 1. In addition, the etching rates of the substrates were investigated in the mixture of $H_2SO_4 : H_3PO_4$=3 : 1 by volume and in the temperature range of 280~320$^{\circ}C$. From the plot of log R against 1/T, the activation penergy ($(E_a)$) was found to be in the order of $({\bar1}012) > (10{\bar1}0) > (11{\bar2}0) > (0001)$ plane. After removing the surface layers of the sapphire with (0001), $({\bar1}012),\;(10{\bar1}0)\;and\;(11{\bar2}0)$ plane by a thickness of 64.6, 46.5, 16.2 and 5.1 ${\mu}m$, respectively, the morphology of the resulting surface was observed by SEM.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.236-237
• /
• 2012

ZnO nanorods were grown on R-plane sapphire substrates with the seed layers annealed at different temperature. The effects of annealing temperature for the seed layers on the properties of the ZnO nanorods were investigated by scanning electron microscopy, X-ray diffraction, UV-visible spectroscopy, and photoluminescence. For the as-prepared seed layers, the ZnO nanorods and the ZnO nanosheets were observed. Only the ZnO nanorods were grown as the annealing temperature was above $700^{\circ}C$. The optical transmittance in the UV region was almost zero while that in the visible region was gradually increased as the annealing temperature increased to $700^{\circ}C$. The optical band gap of the ZnO nanorods was increased as the annealing temperature increased to $700^{\circ}C$. In the visible region, the refractive index was decreased with increasing the wavelength, and the extinction coefficient was decreased as the annealing temperature increased to $700^{\circ}C$. The non-linear exciton radiative life time of the FX emission peak was established by cubic equation. The values of Varshni's empirical equation fitting parameters were ${\alpha}=4{\times}10^{-3}eV/K$, ${\beta}=1{\times}10^4K$, and $E_g(0)=3.335eV$ and the activation energy was found to be about 94.6 meV.