• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.4
• /
• pp.307-313
• /
• 2009

Quantitative analysis of optical scattering intensities from a Au nanoparticle with a diameter of 100 nm, which is effected by the localized surface plasmon resonance (LSPR), were numerically carried out by using a dark-field detection scheme on prism basal plane for two different beam incident modes of reflectance (R-mode) and transmittance (T-mode). Two-dimensional finite difference time domain (FDTD) algorithm was adopted, and its applicabilibility was verified by comparing the simulation results with the theoretical ones. Simulation results of the scattered light intensities from a Au nanoparticle revealed that the scattered intensity of the T-mode was much stronger than that of R-mode. Comparison of the calculated results with the theoretical intensity distribution on the prism showed that the scattered intensity is marimized when the evanescent field, which is generated from the interface of prism and air at TIR angle, is coupled with Au nanoparticle.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.2
• /
• pp.15-22
• /
• 1993

This study was carried out to investigate the fracture criterion of glulam. The mixed mode fracture of glulam was investigated by means of single edge notched specimens with various crack inclination in the longitudinal-radial plane. While fracture of wood is not completely understood, the study on linear-elastic fracture mechanics is a rational and valuable tool for studying the strength behavior of glulam. The results are summarized as follows : 1. Glue line has no effect on fracture strength. 2. There is a definite interaction between fracture toughness $K_I$ and $K_{II}$ during the mixed mode fracture of glulam. Several criterions for mixed mode failure were compared. The criterion was expressed in the following form: $(\frac{K_I}{K_{IC}})^2+(\frac{K_{II}}{K_{IIC}})^2=1$ 3. As crack inclination increases, $K_{IC}$ value and $K_{IIC}$ value decreases. The equations relating crack angle to $K_{IC}$ and $K_{IIC}$, respectively, were obtained as follows; $K_{IC}$ = -77.42${\gamma}$+153.72 ($R^2$ = 0.78) $K_{IIC}$ = -9.17${\gamma}$+34.90 ($R^2$ = 0.48)

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.18 no.2
• /
• pp.77-86
• /
• 2022

This study investigates the effect of the diameter and thickness on crack initiation location and orientation of 90° elbows under in-plane mode displacement-controlled cyclic bending loads. Finite element (FE) analysis of cyclic failure test is conducted for elbow specimens under in-plane mode displacement-controlled cyclic bending to identify the parameters affecting crack location and orientation. Furthermore, parametric FE analysis of the pipe elbows with various pipe nominal sizes and Schedules is performed, and the crack location and orientation from the results of FE analysis are determined. It is found that the crack location and orientation in the pipe elbows are determined mianly by the radius to thickness ratio of pipe elbows (R_m/t). It is also found that the presence of internal pressure slightly increases the value of R_m/t at which the failure mode changes.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.286-289
• /
• 2006

Temporal dual gamma drive technology employing the 120Hz refresh rate was developed to enhance the off-axis viewing quality in patterned vertical alignment mode. The color shift ${\Delta}u'v'$ from on-axis to off-axis (60 deg.) for pale orange color, (R,G,B) = (196,124,96), was below 0.01, and the power exponent of gamma curve for off-axis viewing angle (60 deg.) was about 1.8, when the gamma curve for on-axis was set with power exponent of 2.4. The off-axis image distortion index was below 0.180 in contrast to the normal case ${\sim}0.23$. To elevate the response speed of liquid crystal in the intra-frame, the voltage below threshold voltage of liquid crystals was used.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.73-74
• /
• 2008

In this paper, we suggest a new video coding method using hierarchical block mode structure extension. It is based on the conventional H.264 block modes but adds hierarchically extended block modes to cover large resolution sequences. It is shown by experimental results that the proposed method can achieve a higher coding gain for HD sequences.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.3
• /
• pp.394-400
• /
• 2012

In this paper, charging modes of series resonant converter for a high voltage energy storage capacitor are compared in terms of charging time, peak resonant current, normalized peak resonant current and voltage in each operation mode. Operating principles of the full bridge series resonant converter with capacitor load are explained and analyzed in discontinuous and continuous operation mode. Based on the analysis and simulation result, $0.6{\omega}_r$ < ${\omega}_s$ < $0.75{\omega}_r$ and $1.3{\omega}_r$ < ${\omega}_s$ < $1.4{\omega}_r$ are evaluated to the best range of switching frequency for charging of an high voltage energy storage capacitor. 1.8 kJ/s SRC prototype is assembled with TI 28335 DSP controller and 40 kJ, 7 kV energy storage capacitor. Design rules based on the comparative analysis are verified by experiment.

• Journal of information and communication convergence engineering
• /
• v.17 no.3
• /
• pp.221-226
• /
• 2019

In this work, a transmitter/receiver front-end module (T/R FEM) with an automatic Tx/Rx switching scheme for a 2.4 GHz microwave power transfer is developed for a retro-reflective beamforming scheme. Recently, research on wireless power transfer techniques has moved to wireless charging systems for mobile devices. Retro-reflective beamforming is a good candidate for tracking the spatial position of a mobile device to be charged. In Tx mode, the T/R FEM generates a minimum of 1 W. It also comprises an amplitude and phase monitoring port for transmitting RF power. In Rx mode, it passes an Rx pilot signal from a mobile device to a digital baseband subsystem to recognize the position of the mobile device. The insertion loss of the Rx signal path is 4.5 dB. The Tx and Rx modes are automatically switched by detecting the Tx input power. This T/R FEM is a design example of T/R FEMs for wireless charging systems based on a retro-reflective beamforming scheme.

• Structural Engineering and Mechanics
• /
• v.24 no.4
• /
• pp.493-508
• /
• 2006

Vibration mode localization and frequency loci veering in disordered coupled beam system are studied in this paper using finite element analysis. Two beams coupled with transverse and rotational springs are examined. Small disorders in the physical parameters such as Young's modulus, mass density or span length of the substructure are introduced in the investigation of the mode localization and frequency loci veering phenomena. The effect of disorder in the elastic support on the mode localization phenomenon is also discussed. It is found that an asymmetric disorder in the weakly coupled system will lead to the occurrence of mode localization and frequency loci phenomena.

• Journal of Aerospace System Engineering
• /
• v.2 no.3
• /
• pp.33-39
• /
• 2008

VDL Mode 2 is one of air-to-ground VHF digital data link technologies. The VDL Mode 2 system is designed to be an air-to-ground subnetwork of the Aeronautical Telecommunication Network (ATN) using the AM(R)S band and it is organized according to the Open System Interconnection (OSI) model (defined by ISO). It can be used in ATS Applications especially for ATC communication such as CPDLC and ADS as well. And It is expected VDL Mode 2 replaces ACARS(Aircraft Communications Addressing and Reporting System) which has broadly been used for over 20 years. This paper presents the result of design of operational test equipments for the validation of VDL Mode 2 system under development in KARI.

• 제어로봇시스템학회:학술대회논문집
• /
• 1998.10a
• /
• pp.265-270
• /
• 1998

In this paper we introduce a modeling of wheeled mobile robot with a differential drive derived by R.M. DeSantis and using the dynamics model-ing with some disturbance term we control the wheeled mobile robot using fuzzy sliding mode control(FSMC) method. In a fuzzy control approach it is very difficult to prove the stability of the fuzzy controller. Therefore, to overcome that difficult proof of the stability in a fuzzy control method, we first propose a sliding mode controller and prove the stability of the proposed controller. Next, transforming the proposed sliding mode controller into a fuzzy sliding mode controller without changing the basic structure of the sliding mode con-troller, we easily obtain a fuzzy sliding mode con-troller(FSMC) whose stability is guaranteed with-out difficult stability proof procedure of the proposed FSMC.