• 한국정밀공학회지
• /
• 제32권5호
• /
• pp.491-496
• /
• 2015

Electric handbike can be easily detachable to various sizes of manual wheelchair and the elderly and people with disabilities can use them easily. Therefore, connectors used for coupling between the handbike and manual wheelchair must secure structural stability for occupant safety. However, related research is rare. The aim of this study is to find the connector with highly structural stability by comparing static and dynamic mechanical characteristics among three typical connectors(a snatch lock, a slide latch, and a fastener) by computational simulations. To perform static and dynamic simulation, we referred to durability test based on Korean Standards and then calculated mechanical stresses in connectors. The results showed that the snatch lock addressed the lowest von-mises stress under the same mechanical condition. Therefore when using the combination of a handbike and a wheelchair, we concluded that the snatch lock is considered as the structurally stable connector to structural stability and usability.

• 동력기계공학회지
• /
• 제18권5호
• /
• pp.22-27
• /
• 2014

The objectives of this paper are to obtain an empirical equations regarding the correlations between heat transfer and pressure drop of oval fin-tube heat exchanger having large diameter using wilson plot method. It was difficult to find any recommendable heat transfer and friction factor correlation available for our large diameter experimental cases. Overall heat transfer coefficients are composed of the heat transfer coefficients both inside and outside tubes. The resulting empirical correlations for the Nui and f-factor are given as $Nu_i=0.0146Re^{0.809}Pr^{0.3}$ and $f=4.366Re^{-0.64}$, respectively. The empirical correlations of the Nui and f-factors were developed for the large diameter oval finned-tube heat exchanger as a function of the Reynolds number. As the EG(Ethylene glycol) and air flow rate increases, the heat transfer rate and pressure drop is increased largely.

• 한국소음진동공학회논문집
• /
• 제26권1호
• /
• pp.5-12
• /
• 2016

This paper describes the development process for vibration and acoustic characteristics of a balanced armature speaker. The design parameters were chosen in consideration of the influence of the bending stiffness of balanced armature which is the form of a cantilever structure in the speaker. For study of the performance of the speaker according to the design parameters, in the first step, we analyzed the characteristics of the velocity of the diaphragm to the electrical input. Next step, acoustic characteristics were analyzed by structural-acoustic coupled analysis. And the reliability of the analysis was verified by comparing the result of analysis with test results. Finally, we proposed a design method for implementing an enhanced balanced armature speakers through analysis method.

• 대한임베디드공학회논문지
• /
• 제9권2호
• /
• pp.81-86
• /
• 2014

In the scalable video coding standard, inter-layer prediction based on the coding information of the base layer was adopted to increase the coding performance. This prediction tool results in new syntax elements called motion_prediction_flag (mPF) and residul_prediction_flag(rPF), which are carried to notify the motion vector predictor (MVP) and reference block required in the motion compensation of the decoder. In this paper, an efficient coding method for mPF is proposed to enhance coding efficiency of the salable video coding standard. Through an analysis on the transmission of mPF based on the relationship between the MVPs, we discover the conditions where mPF is unnecessary at the decoder and suggest a modified rate-distortion (RD) cost function to make RD optimization more effective. Simulation results show that the proposed method offers BD rate savings of approximately 1.4%, compared with the conventional SVC standard.

• Asian Journal of Atmospheric Environment
• /
• 제8권2호
• /
• pp.89-95
• /
• 2014

There have been a lot of efforts to keep permissible emission standards and to reduce the amount of emitted air pollutants. There are several air pollution control equipments, however, wet scrubber is used to remove particulate matters and gaseous pollutants simultaneously, even if it has low collection efficiency in the particle size less than $5.0{\mu}m$. To overcome this problem, we introduced a spray tower scrubber with an electrospray system which a high voltage was indirectly applied. We found that collection efficiency of fine particles in the electrospray system was improved by increasing electrical field strength and the ratio of liquid-gas flow rate (from 41% to 84% for $0.3{\mu}m$ particles). In addition, a number of small droplets generated from an electrospray system led high collection efficiency, resulting from electrostatic attraction between droplets and particles and higher collision frequency. Therefore, we can conclude that the introduction of an electrospray system is quite effective to increase the particle removal efficiency of a spray tower scrubber.

• 인터넷정보학회논문지
• /
• 제18권2호
• /
• pp.31-42
• /
• 2017

인터넷 뱅킹 서비스가 보편화되면서 많은 사용자들이 온라인을 통한 재화의 교환이 가능하였다. 하지만 이러한 이점에도 불구하고 인터넷 뱅킹 서비스에서 존재하는 보안위협에 의하여 사고사례가 지속적으로 발생하는 실정이다. 이러한 문제점을 보완하기 위하여 인터넷 뱅킹 서비스의 전 구간에 걸쳐 다양한 보안기술이 적용되었으며, 본 논문에서는 금융기관 구간과 네트워크 구간에 적용된 보안기술에 대한 조사 결과를 서술한다. 본 논문의 결과를 통하여 내부자에 의하여 발생하는 피해사례와 구현과정에서의 취약점으로 인하여 발생하는 위협에 대응하기 위한 참고 자료로써 활용 가치가 있을 것으로 사료된다.

• Journal of Welding and Joining
• /
• 제25권3호
• /
• pp.51-56
• /
• 2007

A $CO_2$ laser overlay was conducted by using a Fe-based powder on the AC2B aluminum substrate. Cracks and intermetallic compounds (IMC) were observed inconsistently along the interface between the overlay and post-molten layer. A scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) detected some Fe-rich IMC ($Fe_3Al$, FeAl) as well as the brittle Al-rich IMC ($Fe_2Al_5,\;FeAl_3$). Micro vickers hardness proved the formation of Al-rich IMC ($FeAl_3$) along the interface by showing HV0.1 $800{\sim}900$. Furthermore, nano indentation was successfully applied to investigate the behavior of IMC more precisely than the micro vickers hardness.

• 한국재난정보학회 논문집
• /
• 제10권1호
• /
• pp.61-70
• /
• 2014

일반적으로 건설재료 용도로 많이 사용되고 있는 유기섬유 보강 콘크리트는 섬유 자체의 인장강도 및 탄성계수는 낮지만, 휨거동, 균열에 대한 저항성 및 충격저항성 등의 특성은 우수하며, 내화학성이 뛰어나고 부식의 우려가 없는 것으로 널리 알려져 있다. 최근 해외에서는 유기섬유 보강재를 터널 숏크리트와 프리캐스트 세그먼트 라이닝, 교량 슬래브 및 PC제품 분야에서 일부 활용되고 있으며, 그 종류 또한 다양하다. 본 연구에서는 다발형 폴리아미드섬유를 혼입한 콘크리트의 휨거동 특성을 ASTM C 1609 및 KS F 2566에 준하여 하중-처짐 관계를 도출하여 유기섬유 보강 콘크리트의 적용 가능성을 검토하였다.

• Food Quality and Culture
• /
• 제2권1호
• /
• pp.20-26
• /
• 2008

Color is one of the most important attributes determining the purchase of food products by consumers. Therefore, the purpose of this study was to identify consumer color preferences for songpyun, a traditional Korean rice cake, by a consumer acceptance test and using coated Pantone color chips. Color evaluation tools for the study were developed accordingly. From the results, the songpyun sample designated as product E was given the highest color acceptability score, and was 'slightly liked' (p<0.05). The color of product E was 'very pale red-purple'. All the evaluated pink-color songpyun products were based on this red-purple hue, however, they had differences in tone. The consumer panel favored a pale tone over a bright tone. The color concept for traditional songpyun within the pink color category was identified as 'very pale red-purple', using coated Pantone color chips. This result for the conceptual color preference was consistent with that of the consumer color acceptance test. Thus, color chips could be an effective tool when applied for color standardization in traditional foods production. From the overall results, it seems consumers are perceiving color trends and are willing to adapt to such changes in food applications.

• 한국전기전자재료학회논문지
• /
• 제29권8호
• /
• pp.516-521
• /
• 2016

Mo-Cu alloys have been widely used for heat sink materials, vacuum technology, automobile, and many other applications due to their excellent physical and electric properties. Especially, Mo-Cu composites with 5 ~ 20 wt.% copper are widely used for the heavy duty service contacts due to their excellent properties like low coefficient of thermal expansion, wear resistance, high temperature strength, and prominent electrical and thermal conductivity. In most of the applications, highly-dense Mo-Cu materials with homogeneous microstructure are required for better performance. In this study, Mo-Cu alloys were prepared by PBM (planetary ball milling) and SPS (spark plasma sintering). The effect of Cu with contents of 5~20 wt.% on the microstructure and thermal properties of Mo-Cu alloys was investigated.