• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.9
• /
• pp.62-66
• /
• 2009

Three inputs of given three magnetic fluxes of an induction motor are calculated. Then, the calculation of magnetic flux for minimum input is repeated using quadratic interpolation method until the convergence criteria are satisfied. The maximum efficiency control is fulfilled with the final magnetic flux for minimum input. Simulation results verify the effectiveness of the proposed method.

• Communications of the Korean Mathematical Society
• /
• v.20 no.4
• /
• pp.861-873
• /
• 2005

In this paper we approximate a cylindrical helix by bi-conic and bi-quadratic Bezier curves. Each approximation method is $G^1$ end-points interpolation of the helix. We present a sharp upper bound of the Hausdorff distance between the helix and each approximation curve. We also show that the error bound has the approximation order three and monotone increases as the length of the helix increases. As an illustration we give some numerical examples.

• Journal of Korea Society of Industrial Information Systems
• /
• v.20 no.5
• /
• pp.1-11
• /
• 2015

This paper is focused on how the trajectory of launch vehicle could be optimally estimated by the quadratic regression of trajectory data mining for the operation of telemetry ground system in NARO space center during real-time. To receive the telemetry data, the telemetry ground system has to track the space launch vehicle without tracking loss, and it is possible by the well-designed algorithm to estimate a flight position in real-time. For this reason, the quadratic regression model instead of interpolation was considered to estimate the exact position data of launch vehicle and the improvement of antenna performance. For analysis, the real trajectory data which had been logged during NARO 1st launch mission were used, the estimation result of launcher current position was analyzed by the mathematical modeling. In conclusion, the algorithm using quadratic regression based on trajectory data mining showed the better performance than previous interpolation algorithm to estimate the next flight position and the antenna driving performance.

• Water for future
• /
• v.29 no.1
• /
• pp.203-212
• /
• 1996

The subject research attempts to develop a new temporal interpolation scheme for the method of characteristics. The proposed three-point time-line Lagrange interpolation Reachback (3PR) method is a temporal quadratic interpolation scheme using the three grid points near the intersection between a characteristic line and a previous time-line. The accuracy of the 3PR method is compared with those of temporal and spatial interpolation schemes such as Reachback, Upwind, and quandratic spatial interpolation methods for two pure advection problems. The results show that on the aspects of the numerical damping and/or oscillation the temporal interpolation schemes are better than the spatial ones under the same interpolation order conditions. In addition, the spatial ones under the same interpolation order conditions. In addition, the proposed 3PR method improves the accuracy of Reachback method as well as it contains the merits of time-line interpolation schemes.

• Structural Engineering and Mechanics
• /
• v.59 no.6
• /
• pp.1071-1094
• /
• 2016

We employ the so-called problem-dependent linked interpolation concept to develop two cubic 4-node quadrilateral plate finite elements with 12 external degrees of freedom that pass the constant bending patch test for arbitrary node positions of which the second element has five additional internal degrees of freedom to get polynomial completeness of the cubic form. The new elements are compared to the existing linked-interpolation quadratic and nine-node cubic elements presented by the author earlier and to the other elements from literature that use the cubic linked interpolation by testing them on several benchmark examples.

• Journal of Mechanical Science and Technology
• /
• v.15 no.2
• /
• pp.192-198
• /
• 2001

We consider an interpolation problem with nonuniform rational B-spline curves given ordered data points. The existing approaches assume that weight for each point is available. But, it is not the case in practical applications. Schneider suggested a method which interpolates data points by automatically determining the weight of each control point. However, a drawback of Schneiders approach is that there is no guarantee of avoiding undesired poles; avoiding negative weights. Based on a quadratic programming technique, we use the weights of the control points for interpolating additional data. The weights are restricted to appropriate intervals; this guarantees the regularity of the interpolating curve. In a addition, a knot placement is proposed for pleasing interpolation. In comparison with integral B-spline interpolation, the proposed scheme leads to B-spline curves with fewer control points.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.425-426
• /
• 2006

Overdriving schemes are used to improve the response time of liquid crystal display. Typically they are implemented by using LUTs (look-up table) within an image processor. However, the size of LUT is limited by the physical memory size and system cost. In this paper, we present an improved method for LUT implementation using linear interpolation and piecewise least-square polynomial regression. Using the proposed method, the performance of LUT can be improved and memory size of that can be reduced.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.2
• /
• pp.310-323
• /
• 1990

A three-noded, with three degree-of-freedom at each node, in-plane curved beam element is formulated and employed in eigen-analysis of constant curvature beam. The conventional quadratic shape functions used in a three noded C .deg. type curved beam element produce such an undesirable large stiffness that a significant error is introduced in displacements and stresses. These phenomena are called 'Stiffness Locking Phenomena', which result from spurious strain energy due to inappropriate assumptions on independent isoparametric quadratic interpolation functions. Stiffness locking phenomena can be alleviated by using modified interpolation functions which get rid of spurious constraints of conventional interpolation functions. Eigenvalues and their modes as well as displacements and stresses may be locked because they are related to stiffness. Using modified curved beam element in eigenvalue problem of cantilever and arch, the property and performance of modified curved beam element are examined by numerical experimentations. In these eigen-analyses, mass matrices are calculated by using both modified and unmodified curved beam element, are compared with theoretical solutions. These comparisons show that the performance of the modified curved beam element is better than that of the unmodified curved beam element.

• Journal of computational fluids engineering
• /
• v.17 no.1
• /
• pp.44-53
• /
• 2012

Immersed boundary method(IBM) is a numerical scheme proposed to simulate flow field around complex objectives using simple Cartesian grid system. In the previous studies, the IBM has mostly been implemented to fractional step method based Navier-Stokes solvers. In this study, we implement the IBM to an incompressible Navier-Stokes solver which uses SIMPLE algorithm. The weight coefficients of the bi-linear and quadratic interpolation equations were formulated by using only geometric information of boundary to reconstruct velocities near IB. Flow around 2D circular cylinder at Re=40 and 100 was solved by using these formulations. It was found that the pressure buildup was not observed even when the bi-linear interpolation was adopted. The use of quadratic interpolation made the predicted aerodynamic forces in good agreement with those of previous studies. For an analysis of moving boundary, we smulated an oscillating circular cylinder with Re=100 and KC(Keulegan-Carpenter) number of 5. The predicted flow fields were compared with experimental data and they also showed good agreements.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.1
• /
• pp.130-140
• /
• 1998

This paper presents a method to estimate subpixel accuracy motion vectors using a mathermatical model withoug interpolation. the proposed method decides the coefficients of mathematical model, which represents the motion vector which is achieved by full search. And then the proposed method estimates subpixel accuracy motion vector from achieved mathematical model. Step by step mathematical models such as type 1, type 2, type 3, modified bype 2, modified type 3, and Partial Interpolation type 3 are presented. In type 1, quadratic polynomial, which has 9 unknown coefficients and models the 3by 3 pixel plane, is used to get the subpixel accuracy motion vectors by inverse matrix solution. In type 2 and 3, each quadratic polynomial which is simplified from type 1 has 5 and 6 unknown coefficients and is used by least square solution. Modified type 2 and modified type 3 are enhanced models by weighting only 5 pixels out of 9. P.I. type 3 is more accurate method by partial interpolation around subpixel which isachieved by type 3. LThese simulation results show that the more delicate model has the better performance and modified models which are simplified have excellent performance with reduced computational complexity.