• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.138-140
• /
• 2002

We fabricated textured Ni substrate for YBCO coated film and evaluated the degree of texture in terms of rolling condition and annealing time. The substrate was compacted from pure Ni powder and reduced the thickness to 100 $\mu$m by rolling followed by heat treatment. As decreasing the thickness of substrate, it was observed that the non-uniform deformation such as ‘wave edge’ or ‘wave buckle’ developed locally on it, causing reduced texture. On the other hand, uniformly deformed substrate showed better cube texture indicating the FWHM of in-plane and out-of-plane of about $11^{\circ}$ ~ $14^{\circ}$. In addition, annealing at $1000^{\circ}C$ for 1~ 8 hr did not make a remarkable difference on the texture.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.391-394
• /
• 2004

In this study, highly thermal stable Ni Germanosilicide has been utilized using NiPt alloy and novel NiPt/Co/TiN tri-layer. And, the Ni Germanosilicide Properties were characterized according to different Ge ratio (x) in $Si_{l-x}Ge_x$ for the next generation CMOS application. The sheet resistance of Ni Germanosilicide utilizing pure-Ni increased dramatically after the post-silicidation annealing at $600^{\circ}C$ for 30 min. Moreover, more degradation was found as the Ge fraction increases. However, using the proposed NiPt/Co/TiN tri-layer, low temperature silicidation and wide range of RTP process window were achieved as well as the improvement of the thermal stability according to different Ge fractions by the subsequent Co and TiN capping layer above NiPt on the $Si_{l-x}Ge_x$. Therefore, highly thermal immune Ni Germanosilicide up to $600^{\circ}C$ for 30 min is utilized using the NiPt/Co/TiN tri-layer promising for future SiGe based ULSI technology.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.2
• /
• pp.169-173
• /
• 2005

Ni oxide thin films were formed through annealing treatment in the atmosphere after Ni thin films deposited by a r.f. magnetron sputtering method and then electric and material properties were analyzed for application to thermal sensors. Resistivity of Ni thin films decreased after annealing treatment at 30$0^{\circ}C$ and 40$0^{\circ}C$ for five hours due to crystallization of Ni thin films but the value increased over 45$0^{\circ}C$ because of Ni thin film's oxidation. Resistivity values of Ni thin films were in the range of 10.5 $\mu$Ωcm/$^{\circ}C$ to 2.84${\times}$10$^4$$\mu$Ωcm/$^{\circ}C$ according to the degree of Ni oxidation. Also temperature coefficient of resistance(TCR) values of Ni oxide thin films depended on the degree of Ni oxidation such as 2,188 ppm/$^{\circ}C$ to 5,630 ppm/$^{\circ}C$ in the temperature range of 0 $^{\circ}C$∼150 $^{\circ}C$. The results demonstrate that Ni oxide thin films of annealing treatment at 40$0^{\circ}C$ for 5hours could be more advantageous than pure Ni thin films and Pt thin films from a point of output properties and TCR, applied to thermal sensors.

• Journal of Radiation Industry
• /
• v.8 no.3
• /
• pp.141-146
• /
• 2014

Nickel (Ni) electroplating was implemented by using a metal Ni powder in order to establish a $^{63}Ni$ plating condition on the PN junction semiconductor needed for production of beta-voltaic battery. PN junction semiconductors with a Ni seed layer of 500 and $1000{\AA}$ were coated with Ni at current density from 10 to $50mA\;cm^{-2}$. The surface roughness and average grain size of Ni deposits were investigated by XRD and SEM techniques. The roughness of Ni deposit was increased as the current density was increased, and decreased as the thickness of Ni seed layer was increased. The results showed that the optimum surface shape was obtained at a current density of $10mA\;cm^{-2}$ in seed layer with thickness of $500{\AA}$, $20mA\;cm^{-2}$ of $1000{\AA}$. Also, pure Ni deposit was well coated on a PN junction semiconductor without any oxide forms. Using the line width of (111) in XRD peak, the average grain size of the Ni thick firm was measured. The results showed that the average grain size was increased as the thickness of seed layer was increased.

• Korean Journal of Materials Research
• /
• v.8 no.3
• /
• pp.206-213
• /
• 1998

Cu, Ni, and Mo were ion-diffused into the pure steel powder in the aqueous solution of $(CuNO_3)_2$, $Ni(NO_3)_2)_2$, and $(NH_4)_6Mo_7O_{24}$, to form partial diffusion bond prealloyed steel powder. The mechanical properties, and compacting and sintering characteristics were investigated as a function of Cu. Ni and Mo contents. The results of the this research, it was found that the smallest change of size was observed, and the good degree of hardness and tensile strength was observed when 1.50wt%Cu, 1.75wt%Ni and 0.50wt%Mo was added each other. The powder metallurgy characteristics of partial diffusion bond prealloyed steel powder containing 1.50wt% of Cu, 1.75wt% of Ni and 0.5wt% of Mo were compared to those of distalloy $AB\textregistered$ which was manufactured in Hogani Corporation of Sweden. Partial diffusion bond prealloyed steel powder of this study had good degree of hardness and density, and its dimensional stability was same to that of pure steel powder. Under the same sintering density and temperature, the tensile strength of the ion powder from this research was $15~20Kg/\textrm{mm}^2$ larger than that of distalloy AB'. also the hardness was larger in the magnitude of Hv20-30. When the powder metallurgy heat-treated, hardness and tensile strength were substantially increased.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.1
• /
• pp.1-6
• /
• 2005

Ni-15at.% W coatings with film thicknesses of 20-40 ㎛ were electroplated on a steel substrate, and their oxidation behavior was investigated at 700 and 800℃ in air. For comparison, a pure Ni coating and a bulk Ni were also oxidized. The Ni-15at.%W coating displayed the worst oxidation resistance, due to the formation of less-protective NiO, Fe₂O₃, NiFe₂O₄ and NiWO₄. The corrosion behavior Ni-15at.%W coatings electroplated on a steel substrate was similarly investigated at 700 and 800℃ in the Ar-l%SO₂ atmosphere. For comparison, the uncoated steel substrate was also corrosion-tested in the Ar-l %SO₂ atmosphere. Severe scale spallation and the internal corrosion of the steel that occurred in the uncoated substrate were not observed in the coated specimen. However, it seemed that the Ni-15at.%W coating cannot be a potential candidate as a sulfidation-resistant coating, due to the formation of less-protective NiO, NiS, WO₃ and NiWO₄.

• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.2
• /
• pp.136-141
• /
• 2005

Li-doped NiO was synthesized by molten salt method. $LiNO_3$-LiOH flux was used as a source for Li doping. $NiCl_2$ was added to the molten Li flux and then processed to make the Li-doped NiO material. Li:Ni ratios were maintained from 5:1 to 30:1 during the synthetic procedure and the Li doping amount of synthesized materials were found between 0.086-0.190 as a Li ion to Ni ion ratio. Li doping did not change the basic cubic structural characteristics of NiO as evidenced by XRD studies, however the lattice parameter decreased from 0.41769nm in pure NiO to 0.41271nm as Li doping amount increased. Hydrogen gas sensors were fabricated using these materials as thick films on alumina substrates. The half surface of each sensor was coated with the Pt catalyst. The sensor when exposed to the hydrogen gas blended in air, heated up the catalytic surface leaving rest half surface (without catalyst) cold. The thermoelectric voltage thus built up along the hot and cold surface of the Li-doped NiO made the basis for detecting hydrogen gas. The linearity of the voltage signal vs $H_2$ concentration was checked up to 4% of $H_2$ in air (as higher concentrations above 4.65% are explosive in air) using Li doped NiO of Li ion/Ni ion=0.111 as the sensor material. The response time T90 and the recovery time RT90 were less than 25 sec. There was minimum interference of other gases and hence $H_2$ gas can easily be detected.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.395-400
• /
• 2003

For the long term storage safety study of the metallic spent fuel, U-Nb, U-Ti, U-Ni, U-Zr, and U-Hf simulated metallic uranium alloys, known as corrosion resistant alloys, were fabricated and oxidized in oxygen gas at $200^{\circ}C~300^{\circ}C$. Simulated metallic uranium alloys were more corrosion resistant than pure uranium metal, and corrosion resistance increases Nb, Ni, Ti in that order. The oxidation rates of uranium alloys determined and activation energy was calculated for each alloy. The matrix microstructure of the test specimens were analyzed using OM, SEM, and EPMA. It was concluded that Nb was the best acceptable alloying elements for reducing corrosion of uranium meta] considered to suitable as candidate.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.4
• /
• pp.161-165
• /
• 2007

In this work, Ni thin films with different thickness from $1,523{\AA}\;to\;9,827{\AA}$ were deposited for the application of micro thermal flow sensors by a magnetron sputtering and oxidized through annealing at $450^{\circ}C$ with increasing annealing time. The initial variation of resistivity decreased radically with increasing films thickness, then gradually stabilizes as the thickness increases. The resistivity of Ni thin films with $3,075{\AA}$ increased suddenly with increasing annealing time at $450{\circ}C$, then gradually stabilizes as the thickness increases after the annealing time 9 h. In case of $3,075{\AA}\;and\;9,827{\AA}$ films, the average of TCR values, measured for the operating temperature range of $0^{\circ}C\;to\;180^{\circ}C$, were $2,413.1ppm/^{\circ}C\;and\;4,438.5ppm/^{\circ}C$, respectively. Because of their high resistivity and very linear TCR, Ni oxide thin films are superior to pure Ni and Pt thin films for flow and temperature sensor applications.

• Particle and aerosol research
• /
• v.10 no.4
• /
• pp.177-182
• /
• 2014

In this study, nickel-coated aluminum (Ni/Al) powders were synthesized for the utilization of energetic applications. Oxide materials present at the surface of Al powders of $45{\mu}m$ in averaged size were removed by using sodium hydroxide(NaOH) solution which is used for controlling pH. Nickel material is coated into the surface of oxide-removed Al powders by electroless-plating process. The microstructure of fabricated Ni/Al powders shows that nickel layers with a few hundreds nm were very homogeneously formed onto the surface of Al powders. The oxidation behavior of Ni/Al exihibit somewhat faster oxidation rate than that of pure Al with surface oxidation. Also, the higher exothermic reaction was observed from the Ni/Al powders. From the result of this, nickel coating is very promising method to obtain highly reactive and safe Al powders for energetic applications.