• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3383-3388
• /
• 2014

An experimental study was performed to compare the characteristics of the combustion pressure and exhaust emissions in the case of using pure diesel when the EGR rate was changed in a CRDI 4-cylinder diesel engine with those using biodiesel blended and pure diesel fuel. In this study, the EGR rate variation were conducted at an engine speed of 2000rpm with fuel with a biodiesel blended rate of 20%. The combustion pressure of the biodiesel blended rate 20% and pure diesel fuels decreased with increasing EGR rate. The IMEP of biodiesel was higher than that of ULSD (Ultra low sulfur diesel). The emission results showed that the NOx emission of biodiesel blended fuel with increasing EGR rate was higher than that of ULSD. In addition, the NOx emission of biodiesel blended and diesel fuel decreased with increasing EGR rate. The CO and soot, $CO_2$ emissions increased with increasing EGR rate, and the CO and soot emissions from the biodiesel blended fuel were lower than that of ULSD but the $CO_2$ emissions were higher.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.10a
• /
• pp.21-24
• /
• 2000

Ultra-fine grains were produced in pure Al using an Accumulative Rolling-Bonding (ARB) process. After several cycles of the ARB process, pure Al sheets were filled with the ultra-fine grains whose diameters were several hundred nano-meters. With ARB cycles, the nature of grain boundaries of the ultra-fine grains changed from diffusive sub-boundaries to well-defined high angle boundaries. After 7 cycles, ultra-fine polycrystals with large misorientations between neighboring grains were obtained. Sliding wear tests using a pin-on-disk type wear tester were co ducted on the ultra-fine grained pure Al. Wear rates of pure Al increased with the increase of ARB cycle numbers in spite of the increase in hardness. Worn surfaces and cross-sections were examined with optical microscopy (OM) and scanning electron microscopy (SEM) In investigate the wear mechanism of the ultra-fine grained pure Al.

• Journal of computational fluids engineering
• /
• v.18 no.3
• /
• pp.1-7
• /
• 2013

A pure oxygen combustion technology is crucial in Carbon Capture and Storage (CCS) technology especially in capturing of $CO_2$, where CCS will reduce 9 $GtCO_2$ by 2050, which is 19% of the total $CO_2$ reduction amount. To make pure oxygen combustion feasible, a regenerative system is required to enhance the efficiency of pure oxygen combustion system. However, an existing air combustion technology is not directly applicable due to the absence of nitrogen that occupies the 78% of air. This study, therefore, investigates the heat and fluid flow in a regenerative system for pure oxygen combustion by using commercial CFD software, FLUENT. Our regenerative system is composed of aluminium packed spheres. The effect of the amount of packed spheres in regenerator and the effect of presence or absence of a bypass of exhaust gas are investigated. The more thermal mass in regenerator makes the steady-state time longer and temperature variation between heating and regenerating cycle smaller. In the case of absence of bypass, the regenerator saturates because of enthalpy imbalance between exhaust gas and oxygen. We find that 40% of exhaust gas is to be bypassed to prevent the saturation of regenerator.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.526-529
• /
• 2008

By combining tetraphenylethylene and anthracene, we synthesized 9,10-bis(4-(1,2,2-triphenylvinyl)phenyl) anthracene [BTPPA] and 1,2-di(4'-tert-butylphenyl)-1,2-bis(4'-(anthracene-9-yl)phenyl)ethene [BPBAPE]; both BTPPA and BPBAPE have similar band-gaps, however their PL spectra were shifted by about 30 nm with respect to each other. The fabricated multilayered non-doped OLED devices based on pure BTPPA or BPBAPE exhibited luminance efficiencies of 3.93 cd/A at 6.8 V and 10.33 cd/A at 8.1 V, respectively, at $10\;mA/cm^2$. As the BPBAPE content of the emitting layer increased, the luminance efficiency of the device increased; in addition, the CIE coordinates of the fabricated devices shifted gradually from deep-blue for pure BTPPA to sky-blue for pure BPBAPE.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.735-742
• /
• 2000

Densification behaviors of mixed metal powder under high temperature were investigated. Experimental data of mixed copper and tool steel powder with various volume fractions of Cu powder were obtained under hot isostatic pressing and hot pressing. By mixing the creep potentials of McMeeking and co-workers and of Abouaf and co-workers originally for pure powder, the mixed creep potentials with various volume fractions of Cu powder were employed in the constitutive models. The constitutive equations were implemented into a finite element program (ABAQUS) to compare with experimental data for densification of mixed powder under hot isostatic pressing and hot pressing. Finite element calculations by using the creep potentials of Abouaf and co-workers agreed reasonably well with experimental data, however, those by McMeeking and co-workers underestimate experimental data as observed in the case of pure metal powders.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.2
• /
• pp.167-172
• /
• 2009

Direct methanol fuel cells(DMFCs) are receiving significant attention in the portable power source and electric vehicular transportation because of its high energy efficiency as liquid fuel, low cost, and no requirement of fuel reforming process. In this study, we synthesized the Sulfonated poly(ether ether ketone) (SPEEK) to evaluate the possibility of use as a proton exchange membrane for DMFC. And poly(vinylidienedifluoride) (PVDF) was used to increase proton conductivity in SPEEK and simultaneously to prevent methanol transport through the cross linked membrane. Furthermore, in order to improve the electrical composite properties for DMFC applications.

• Journal of Korean Society for Atmospheric Environment
• /
• v.30 no.1
• /
• pp.68-76
• /
• 2014

The present study has evaluated the $CO_2$ adsorption amount of activated carbon pellets (AC). Coconut shell based test AC were modified with surface impregnation of glycine, glycine metal salts and monoethanolamine for low level $CO_2$ (3000 ppm) adsorption. Physical and chemical properties of prepared adsorbents were analyzed and the adsorbed amount of $CO_2$ was investigated by using pure and 3,000 ppm $CO_2$ levels. The impregnation of nitrogen functionalities was verified by XPS analysis. The adsorption capacity for pure $CO_2$ gas was found to reach upto 3.08 mmol/g by AC-LiG (Activated carbon-Lithium glycinate), which has the largest specific surface area ($1026.9m^2/g$). As for low level $CO_2$ flow the primary amine impregnated adsorbent showed 0.26 mmol/g of adsorption amount, indicating the highest selectivity. An adsorbent with potassium-glycine salts (AC-KG, Activated carbon-Potassium glycinate) instead of amine presented with 0.12 mmol/g of adsorption capacity, which was higher than that of raw activated carbon granules (0.016 mmol/g).

• Journal of Sensor Science and Technology
• /
• v.28 no.5
• /
• pp.271-276
• /
• 2019

Pure and 0.5, 1, 2, 5, and 10 at% of Mo-doped $Co_3O_4$ yolk-shell spheres were synthesized by ultrasonic spray pyrolysis of droplets containing Co nitrate, ammonium molybdate, and sucrose and their gas sensing characteristics to 5 ppm trimethylamine (TMA), ethanol, p-xylene, toluene, ammonia, carbon monoxide, and benzene were measured at $225-325^{\circ}C$. The sensor using pure $Co_3O_4$ yolk-shell spheres showed the highest response to p-xylene and very low response to TMA at $250^{\circ}C$, while the doping of Mo into $Co_3O_4$ tended to increase the overall responses of gas sensors. In particular, the sensor using 5 at% Mo-doped $Co_3O_4$ yolk-shell spheres exhibited the high response to TMA with low cross-responses to other interfering gases. The high response and selectivity of Mo-doped $Co_3O_4$ yolk-shell spheres to TMA are attributed to the electronic sensitization by higher valent Mo doping and acid-base interaction between TMA and Mo components.

• Journal of Industrial and Engineering Chemistry
• /
• v.67
• /
• pp.156-163
• /
• 2018

High-performance mixed-matrix membranes that comprise both zeolitic imidazolate framework-8 (ZIF-8) and graphene oxide (GO) were synthesized with a solution casting technique to realize excellent $CO_2/CH_4$ separation. The incorporation of ZIF-8 nanocrystals alone in ODPA-TMPDA polyimide can be used to significantly enhance $CO_2$ permeability compared with that of pure ODPA-TMPDA. Meanwhile, the addition of a GO nanostack alone in ODPA-TMPDA contributes to improved $CO_2/CH_4$ selectivity. Hence, a composite membrane that contains both fillers displays significant enhancements in $CO_2$ permeability (up to 60%) and $CO_2/CH_4$ selectivity (up to 28%) compared with those of pure polymeric membrane. Furthermore, in contrast to the ZIF-8 mixed-matrix membrane, which showed decreased mechanical stability, it was found that the incorporation of GO could improve the mechanical strength of mixed-matrix membranes. Overall, the synergistic effects of the use of both fillers together are successfully demonstrated in this paper. Such significant improvements in the mixed-matrix membrane's $CO_2/CH_4$ separation performance and mechanical strength suggest a feasible and effective approach for potential biogas upgrading and natural gas purification.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.5
• /
• pp.222-227
• /
• 2018

$Zn_{1-x}Co_x$ Zeolitic Imidazolate Framework (ZIF) (x = 0~0.05) were prepared by the co-precipitation of $Zn^{2+}$ and $Co^{2+}$ using 2-methylimidazole, which were converted into pure and Co-doped ZnO nanoparticles by heat treatment at $600^{\circ}C$ for 2 h. Homogeneous Zn/Co ZIFs were achieved at x < 0.05 owing to the strong coordination of the imidazole linker to $Zn^{2+}$ and $Co^{2+}$, facilitating atomic-scale doping of Co into ZnO via annealing. By contrast, heterogeneous Zn/Co ZIFs were formed at $x{\geq}0.05$, resulting in the formation of $Co_3O_4$ second phase. To investigate the potential as high-performance gas sensors, the gas sensing characteristics of pure and Co-doped ZnO nanoparticles were evaluated. The sensor using 3 at% Co-doped ZnO exhibited an unprecedentedly high response and selectivity to trimethylamine, whereas pure ZnO nanoparticles did not. The facile, bimetallic ZIF derived synthesis of doped-metal oxide nanoparticles can be used to design high-performance gas sensors.