• International Journal of Fluid Machinery and Systems
• /
• 제6권4호
• /
• pp.206-212
• /
• 2013

Self-excited pulse jet is a specific nozzle with a closed chamber which can change a continuous jet into a pulse one. Energy of the pulse jet can be output not only unevenly but also with multifrequency. With the peak pressure of pulse jet, the hitting power would be 2~2.5 times higher than that of continuous jet. In order to reveal the correlation between the self-excited pulse frequency and nozzle diameter ratio, nozzle spacing and operating pressure, the model of 3D unsteady cavitation model has been used. We found that with the same nozzle structure parameters and the different operating pressure, the self-excited frequency and the width of peak crest are different, but the wave profiles are similar. With FFT, we also found that the less bandwidth of amplitude in low frequency range will lead to the wider wave crest of outlet velocity in its time domain, and the larger force of the strike will be gained. By studying the St of self-excite nozzle, not only the frequency of a certain nozzle can be predicted, but also a nozzle structure with a certain frequency can be designed.

• Journal of Power Electronics
• /
• 제17권6호
• /
• pp.1422-1432
• /
• 2017

This paper presents a buck-boost converter-based bipolar pulse generator, which is able to generate bipolar exponential pulses across a resistive load. The concept of the proposed approach depends on operating the involved buck-boost converters in discontinuous current conduction mode with high-voltage gain and enhanced efficiency. A full design of the pulse generator and its passive components is presented to ensure generating the pulses with the desired specifications (rise time, pulse width, and pulse magnitude) for a given load resistance and input dc voltage. In case of moderate pulsed output voltages (i.e. few of kV), one module of the presented bipolar generator can be employed. While in case of high-voltage pulsed output, multi-module version can be employed, where each module is fed from an isolated dc source and their outputs are connected in series. Simulation models for the proposed approach are built to elucidate their performance in case of one-module as well as multi-module based generator. Finally, a scaled-down prototype for one-module of buck-boost converter-based bipolar pulse generator is implemented to validate the proposed concept.

• Journal of Communications and Networks
• /
• 제5권4호
• /
• pp.365-373
• /
• 2003

This paper investigates the performance of M-ary pulse position modulation (PPM) multiuser ultra-wideband (UWB) communication systems in terms of symbol error rate (SER) over fading and additive white Gaussian noise (AWGN) channel. Based on Gaussian approximation for the multiple access interference, an expression for the signal-to-noise ratio (SNR) is derived for the UWB system. This expression is used to derive exact SER expressions for coherent UWB receivers. The effect of pulse selection on the SER of multiuser UWB system is studied. In addition to rectangular pulse, the 2nd derivative Gaussian waveform and Rayleigh pulses were considered. We show that the system capacity and/or SER performance can be significantly increased by using the monocycle pulse in fading channels.

• Steel and Composite Structures
• /
• 제36권3호
• /
• pp.249-259
• /
• 2020

In this work, a novel three-dimensional model in the generalized thermoelasticity for a homogeneous an isotropic medium was investigated with diffusion, under the effect of thermal loading due to laser pulse in the context of Green-Lindsay theory was investigated. The normal mode analysis technique is used to solve the resulting non-dimensional equations of the problem. Numerical results for the displacement, the thermal stress, the strain, the temperature, the mass concentration, and the chemical potential distributions are represented graphically to display the effect of the thermal loading due to laser pulse and the relaxation time on the resulting quantities. Comparisons are made within the theory in the presence and absence of laser pulse.

• 전기의세계
• /
• 제29권2호
• /
• pp.118-128
• /
• 1980

The properties of plasmas produced by high power glass laser were investigated with various methods of diagnostics. Electron temperature was estimated by measurement of soft X-ray, and ion temperature was estimated by measurement of the time-of-flight of ion. The measurement of incident and reflected laser light, and Schlieren and shadowgragh methods were also used. No influence of laser pulse duration on the temperature was observed in the case of durations 2, 4 and 10 nsecs. The effective heating of plasma occurred in about 2 nsec of beginning of incident laser pulse. The experimental results for fast rising laser pulse were discussed and the influence of resetime of laser pulse on the heating of plasma was described. Neutrons produced by irradiating laser beam to solid deuterium target were detected.

• 한국환경과학회지
• /
• 제16권4호
• /
• pp.449-458
• /
• 2007

Research results for the pressure drop variance depending on operation conditions such as change of inlet concentration, pulse interval, and face velocity, etc., in a pulse air jet-type bag filter show that while at $3kg/cm^2$ whose pulse pressure is low, it is good to make an pulse interval longer in order to form the first layer, it may not be applicable to industry because of a rapid increase in pressure. In addition, the change of inlet concentration contributes more to the increase of pressure drop than the pulse interval does. In order to reduce operation costs by minimizing filter drag of a filter bag at pulse pressure $5kg/cm^2$, the dust concentration should be minimized, and when the inlet dust loading is a lower concentration, the pulse interval in the operation should be less than 70 sec, but when inlet dust loading is a higher concentration, the pulse interval should be below 30 sec. In particular, in the case that inlet dust loading is a higher concentration, a high-pressure distribution is observed regardless of pulse pressure. This is because dust is accumulated continuously in the filter bag and makes it thicker as filtration time increases, and thus the pulse interval should be set to below 30 sec. If the equipment is operated at 1m/min of face velocity, while pressure drop is low, the bag filter becomes larger and thus, its economics are very low due to a large initial investment. Therefore, a face velocity of around 1.5 m/min is considered to be the optimal operation condition. At 1.5 m/min considered to be the most economical face velocity, if the pulse interval increases, since the amount of variation in filter drag is large, depending on the amount of inlet dust loading, the operation may be possible at a lower concentration when the pulse interval is 70 sec. However, for a higher concentration, either face velocity or pulse interval should be reduced.

• 대한기계학회논문집A
• /
• 제21권3호
• /
• pp.485-501
• /
• 1997

Pressure control is possible driving a simple ON/OFF 3-way valve of hydraulic servo system by pulse width modulation signal. But the pressure varies according to the duty ratio and carrier frequency and repeated on-off action induces pressure fluctuation. So equations for mean pressure and ripple amplitude are theoretically derived as a function of on/off time, the system parameters which decide the pressure characteristics are arranged and they are verified by experimental study. As the result selection criteria for the major design parameters are established and the basic strategy to suppress the unnecessary fluctuation can be provided for a hydraulic pressure control system using these type of valves.

• 전자공학회논문지T
• /
• 제36T권1호
• /
• pp.79-85
• /
• 1999

마이크로 스트립 다중 선로의 고속 디지털 펄스 신호에 대한 상호 결합 특성을 신간영역에서 등가 회로 모델을 사용하여 나타내었다. MMIC 설계시 펄스의 상승시간과 주파수 및 듀티 사이클에 따른 간섭과 누화 특성을 분석하기 위해 SPICE용 알고리즘을 개발하였고, 이 알고리즘에 희한 해석 결과를 Branin 법과 FDTD법에 의한 결과와 비교하여 일치함을 보였다. 해석은 결합 마이크로 스트립 선로의 기하학적 구조에서 펄스의 특성에 따른 전송 특성을 중심으로 나타내었다. 본 논문의 결과는 MIC 나 MMIC 회로 설계시 신호의 주파수와 결합선로의 구조적 문제를 CAD 프로그램에서 직접 해석하여 간섭 효과를 줄이는데 적용할 수 있다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.265-269
• /
• 1994

The switching dead time avoiding a bridge leg short circuit in PWM voltage source inverter produces distortions of the controlling inverter output performance such as current waveform, voltage vector, and torque. In this paper, the influence of dead time is investigated. The on-line space voltage vector modulation method is used for current controller. It is possible to compensate dead time by space voltage vector modulation which generates additional pulse compensating voltage distortion caused by dead time. In addition, narrow pulse which is generally neglected can be compensated. All the algorithms, including field-oriented control are performed by one chip microprocessor 80C196MC and DSP TMS320C31. Experimental results probe that the proposed scheme provides a good inverter output performance.

• 한국지진공학회논문집
• /
• 제10권3호
• /
• pp.101-111
• /
• 2006

이 논문에서는 안정대륙권역(Stable Continental Regions, SCRs)에서의 중규모 지진에 의한 근단층지반운동(Near Fault Ground Motion, NFGM) 모델을 처음으로 제시한다. 근단층지반운동은 큰 진폭의 장주기 속도 펄스를 갖는 특징을 가지고 있다. 이 속도 펄스를 모델링하기 위해서는 그 주기와 진폭을 지진의 규모와 단층거리의 함수로 표현할 수 있어야 한다. 그런데 안정대륙권역에서는 관측 자료가 빈약하여 지진데이터로부터 이 관계식을 직접 유도하는 것은 어렵기 때문에 이 연구에서는 간접적인 접근법을 채택하였다. 속도 펄스의 주기와 진폭은 단층파열의 상승시간과 파열속도의 함수임이 알려져 있고 활성구조권역(Active Tectonic Regions, ATRs)에 속하는 미국 서부지역에서는 실험적 공식이 확립되어 있다. 안정대륙권역에서의 상승시간과 단층파열속도의 지진규모에 대한 함수관계는 WUS와 CEUS에서의 자료를 비교하여 도출하였다. 이 관계식들로부터 안정대륙권역에서의 NFGM의 속도 펄스의 주기와 진폭을 지진규모 및 단층 거리에 대한 관계식으로 유도하였다. 안정대륙권역에서의 NFGM의 가속도 시간이력은 추계학적으로 생성된 원역지진지반가속도에 새로운 관계식에 의한 속도 펄스를 중첩하여 얻어진다. 적용 예제로서 탄소성 단자유도 시스템의 근단층지반운동에 대한 응답을 분석하였다.