• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.335-338
• /
• 2010

The moisture in the atmosphere exerts a lot of influence upon Gas turbine engine performances. There is a noticeable influence of wet air at the summer sea level, high flight mach number and low engine rpm increasingly. An altitude Engine Test Facility is used to accomplish the engine performance tests at dry air condition and wet air condition, through which engine performance results is revealed. In the result, net thrust and specific fuel consumption measured -2.826% and 1.325%, respectively at wet air condition compared to dry air condition.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.153-156
• /
• 2008

Ignition and combustion performance of a gas-turbine engine were changed by various high-altitude condition. A goal of this study is to make the small test facility to simulate high-altitude condition. To perform the low pressure condition, a diffuser was used in various diffuser front of primary nozzle pressure. To perform the low temperature, heat exchanger was used in various mixture ratio of cryogenic air and ambient temperature air. The experimental result shows that high-altitude conditions can be controled by diffuser front of primary nozzle pressure and mixture ratio of cryogenic air and ambient temperature air.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.1
• /
• pp.69-75
• /
• 2016

This paper covers the result of construction and start-up tests of the KSLV(Korea Space Launch Vehicle)-II combustion chamber hot-firing test facility. This facility was constructed from 2012 to 2014. Start-up test of this facility began in the second half of 2014. Oxidizer cold flow test, fuel cold flow test and cooling water cold flow test were carried out as start-up test. Afterward, ignition test of combustion chamber was accomplished. The result of ignition test is applied to set up start-up sequence of KSLV-II combustion chamber and utilized as base line data for hot-firing test of low and normal design point.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.181-184
• /
• 2003

We manufactured standard motor to measure burning rate of propellant, used to estimate burning rate of main motor by static fired testing. We installed static fired testing facility and developed standard motor more lightly to accomplish the test. As a result of the tests, we could get the burning rate closer than acquired by existing method to the main motor's on. And we confirmed repeatability by many times of tests. We will use this method positively for R&D and quality assurance activity of mass production.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.178-182
• /
• 2007

This paper reviews on the LRE health monitoring and emergency protection system to protect test object engine system and engine test facility, in case of various fault occurrence at LRE testing. General composition and major technical consideration of LRE health monitoring system and emergency protection system are reviewed. Moreover, some application of LRE health monitoring/emergency protection system to development test of major LRE component such as turbopump testing, gas generator and combustion chamber test are reviewed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.159-167
• /
• 2005

Considering the increase of interest in $H_{2}O_2$ as a rocket propellant, a test facility and a rocket engine have been developed to research in areas of $H_{2}O_2$ mono-propellant propulsion. A detailed design-study of a $H_{2}O_2$ mono-propellant rocket engine of 100-N thrust is presented. Several firings attempted in early stage had some problems with misfire and chamber pressure decrease. Low environmental temperature and impurities included in hydrogen peroxide were considered to be the reasons. Addressing these points resulted in successful firing of the rocket engine and obtained thrust about $100\sim107-N.$

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.110-117
• /
• 2006

Considering the increase of interest in $H_2O_2$ as a rocket propellant, a test facility and a rocket engine have been developed to research in areas of $H_2O_2$ mono-propellant propulsion. A detailed design-study of a $H_2O_2$ mono-propellant rocket engine of 100-N thrust is presented. Several firings attempted in early stage had some problems with misfire and chamber pressure decrease. Low environmental temperature and impurities included in hydrogen peroxide were considered to be the reasons. Addressing these points resulted in successful firing of the rocket engine and obtained thrust about $100\sim107-N$.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.892-897
• /
• 2011

The propulsion system of space launch vehicle generates thrust by supplying oxidizer and fuel to combustion chamber. KSLV-II 2nd stage engine, currently under development by KARI, is to use liquid oxygen as a oxidizer and JET-A1 as a fuel. The 2nd stage pump-fed engine is mainly composed of combustion chamber, turbo-pump and engine supply system. To develop liquid propulsion engine, the development of combustion chamber must be preceded. For performance validation of the combustion chamber, the designed and manufactured combustion chamber should be tested in combustion chamber test facility(CCTF). The detailed design for the planned CCTF in Naro Space Center was conducted. The fuel supply system modeling using AMESim was performed based on the results of the detailed design, and the fuel supply characteristics was analyzed in this paper.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.2
• /
• pp.44-53
• /
• 2003

A vertical hot-firing test facility was established to carry out the IPPT(Integrated Propulsion Performance Test) and SQT(Stage Qualification Test) of KSR-III(Korea Sounding Rocket-III). The components for actual launcher were mostly used, hence these tests were carried out under the condition of relatively lower safety margin. To perform hot-firing tests with the maximum safety, an engine emergency blockage system was investigated and applied. An emergency blockage system using combustion chamber pressures and acceleration signals was set up to monitor ignition delay and fail, flame out, propellant feeding status, unstable combustion and excessive structural vibration. With such a system, the test safety could be secured by rapid judgement and follow-up measures, which made IPPT and SQT be safely completed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.2
• /
• pp.95-103
• /
• 2019

Control systems of compressed gas supply facility are responsible for storing and supplying compressed gases required for launch complex qualification test and launch operation. Most of the facilities that make up the launch complex require compressed gas for their operation. Therefore, such control systems should be developed and verified earlier rather than the other systems that constitute the launch complex. Each verification for hardware and software is performed separately. In particular, software verification of control algorithms loaded on the controller takes a lot of time and man power during the development period of the control system. Thus, specific test procedures and methods should be prepared in advance for efficient development. This paper introduces the configuration of a compressed gas supply facility and its control system with the verification procedure and results of major algorithms.