• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.61-64
• /
• 2003

A comprehensive understanding is given for the hot-firing test results, which were obtained throughout the verification program of mono-propellant hydrazine thrusters producing 0.95 lbf (4.2 Newtons) of nominal steady-state thrust at an inlet pressure of 350 psia (2.41 ㎫). The scrutiny is made in terms of thrust and temperature behavior of steady state firing mode at the given propellant injection pressures of 400, 250, 100, and 50 psi. Engineering philosophy of data measurement and reduction is shortly mentioned, too.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.3
• /
• pp.41-46
• /
• 2020

In this study, measurement and analysis results from Differential scanning calorimetry(DSC) and Thermogravimetric analysis(TGA) on the newly developed high-energy thermoplastic elastomer(ETPE) propellant are described, followed by the previous study done under the same title as this paper [1]. The characteristics of high-energy thermoplastic propellant were also verified by conducting thermal analysis, and the LSGT, Shotgun & RQ Bomb test, was carried out as well. High energetic thermoplastic binders containing 45% of GAP(Glycidyl Azide Polymer), energetic plasticizer(DEGDN) and Oxidizer Aonium Perchlorate), RDX(reseach development explosive, cyclotrimethylenetrinitramine) were used to formulate the propellant.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.1
• /
• pp.14-19
• /
• 2016

The viscosity and mechanical property of HTPB/AP composite solid propellant are profoundly affected by particle size of AP. In HTPB/AP propellant formulated by two mode of AP size such as $190{\mu}m$ and $7{\mu}m$, the propellant was found to be much less viscose at end of mix when coarse/fine AP ratio is ranged from 70/30 to 60/40 due to high solid packing fraction. It was shown that the toughness of tensile strength test for HTPB/AP propellant increased with the increase in coarse AP. Considering both lower viscosity and better tensile strength, the optimum ratio of AP coarse/fine was estimated to be 70/30.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.268-271
• /
• 2006

Combustion response function of a solid propellant is measured and calculated to study and model the feedback process between acoustic waves and combustion field. Standard Pulsed DB/AB method and related one-dimensional approximate analysis of T-burner are used to obtain the response function at a driving natural frequency. The problems related with simultaneous ignition of propellant samples are also mentioned and treated.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.4
• /
• pp.514-519
• /
• 2017

To develop a gun propellant composition with high insensitivity and high energy, we formulated a composition by adding RDX into the nitrocellulose(NC) based propellant. The flame temperature of the RDX added NC(RAN) propellant was higher than that of neat NC propellant. The kinetic muzzle energy of RAN propellant was close to that of JA2 propellant at room temperature($21^{\circ}C$). The difference of kinetic muzzle energy of RAN propellant between high and room temperature settings as well as between a low and room temperature settings were less compared to those of JA2 propellant.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.61-65
• /
• 2005

In HTPB/AP propellants, zirconium(Zr) addition to formulation was shown to be less specific impulse than aluminum(Al) by the theoretical calculation because of the lower flame temperature and higher molecular weight of Zr oxide. It was found that the burning rate was faster with the finer size of Zr and the more content of $2{\mu}m$ Zr the faster burning rate is in HTPB/AP/Zr propellants caused by the more conduction energy transfer from Zr flame to the burning surface. Also the burning rate of HTPB/AP/Zr propellant could be reduced by addition of 150nm Al, depending on AP size distribution in formulation with Butacene and $1{\mu}m$ AP.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.2
• /
• pp.9-16
• /
• 2005

Zirconium(Zr) addition to formulation of HTPB/AP propellants, was shown to be less specific impulse than aluminum(Al) by the theoretical calculation because of the lower flame temperature and higher molecular weight of Zr oxide. It was found that the burning rate was faster with the finer size of Zr and the more content of $2{\mu}m$ Zr the faster burning rate is in HTPB/AP/Zr propellants caused by the more conduction energy transfer from Zr flame to the burning surface. Also the burning rate of HTPB/AP/Zr propellant could be reduced by addition of 150nm Al, depending on AP size distribution in formulation with Butacene and $1{\mu}m$ AP.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.107-113
• /
• 2000

Design configuration and performance requirements for KOMPSAT-1 propulsion system were described. Operational results of the propulsion system obtained through the satellite Launch and Early Operation Phase were scrutinized. Performance characteristics of the thrusters which are employed for spacecraft attitude control and the corresponding propellant depletion rate were analysed according to satellite operation modes. Additionally, propellant leakproof and thermal control capability were checked out from the view point of system verification. Propellant depletion rates calculated by PVT method in $\Delta$V maneuvering and each attitude control mode produce the very meaningful results for the prediction of total propellant consumption up to the end of satellite mission life.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.383-386
• /
• 2006

Several HTPB/AP and HTPB/AP/HMX propellants were investigated experimentally for ignition characteristics in subatmospheric pressure. The threshold ignition pressure was 4psia for HTPB/AP composite propellant. The partial replacement of AP in HTPB/AP composite propellant by $5\sim15%$ of HMX, HNIW showed improvements in the threshold pressure was below 0.4psia. This appears to be due to the exothermic dissociation characteristics of HMX and HNIW at lower temperature $(\sim220^{\circ}C)$ than that of AP. The ignition substance B/KNO3 was coated thinly on the propellant surface for better ignition effect. As a result, ignition delay time of 15% was improved. NC is applied to $B/KNO_3$ ignition substance as a secondary binder and $NC-B/KNO-3$ suspension solution is coated to the propellant surface.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.698-701
• /
• 2011

Over recent several years, researches for the less sensitive gun propellant development have been carried out with promising the product of propellants which have temperature independent characteristics using the new energetic plasticizing mixture as Di-nitro-diaza-alkanes. During this study, the promising propellant formulation having temperature ballistic properties as well as better behaviors concerning the cold brittleness of the materials was confirmed by results in tests of a closed bomb and 40mm Gun firing. On-going research on the optimized shape, formulation and processes of the propellant is progressing. From now on it should be done present study to establish the better composition and processes.