• The Transactions of the Korea Information Processing Society
• /
• 제4권11호
• /
• pp.2822-2831
• /
• 1997

A B-ISDN network based on ATM must support several kinds of transport services with different traffic characteristics and service requirements. There is neither link-by-link flow control nor error control in the ATM layer. For different services, different flow/error controls could be performed at the AAL layer or at a higher Iayer(e.g. transport layer). In traditional data networks, the window now control mechanism combined with error control was used prevalently. But, the window flow control mechanism might be useless in ATM networks because the propagation delay is too large compared with the transmission rate. In this paper, we propose a simple flow control mechanism, called RCT(Rate Control for end-to-end Transport), for end-to-end data transport. The RCT shows acceptable performance when the average overload period is bounded by a certain time.

• The Transactions of the Korean Institute of Power Electronics
• /
• 제10권3호
• /
• pp.282-289
• /
• 2005

This paper proposes a fuzzy neural network controller based on the vector control for interior permanent magnet synchronous motor(IPMSM) drive system. The hybrid combination of neural network and fuzzy control will produce a powerful representation flexibility and numerical processing capability This paper does not oかy presents speed control of IPMSM using neuro-fuzzy control(NFC) but also speed estimation using artificial neural network(ANN) controller. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. The error between the desired state variable and the actual one is back-propagated to adjust the rotor speed, so that the actual state variable will coincide with the desired one. The back propagation mechanism is easy to derive and the estimated speed tracks precisely the actual motor speed. Thus, it is presented the theoretical analysis as well as the analysis results to verify the effectiveness of the proposed method in this paper.

• Journal of the Korean Institute of Intelligent Systems
• /
• 제16권1호
• /
• pp.8-17
• /
• 2006

It is essential for robot to have the sensing and communication abilities in the swarm robot system. In general, as the number of robot goes on increasing, the limitation of communication capacity and information overflow occur in global communication system. Therefore a local communication is more effective than global one. In this paper, we analyze information propagation mechanism based on local communication. To find an optimal communication radius, we propose several methods with different conditions. Also, to avoid chaotic behavior which occurs when a robot obtains and loses information, we will suggest the stable condition of information propagation.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제33권7호
• /
• pp.477-485
• /
• 2009

The study of nitrogen dilution effect on the flame stability was experimentally investigated in a non-premixed turbulent lifted hydrogen jet with coaxial air. Hydrogen gas was used as a fuel and coaxial air was used to make flame liftoff. Each of hydrogen and air were injected through axisymetric inner and outer nozzles ($d_F=3.65\;mm$ and $d_A=14.1\;mm$). And both fuel jet and coaxial air velocity were fixed as $u_F=200\;m/s$ and $u_A=16\;m/s$, while the mole fraction of nitrogen diluents gas was varied from 0.0 to 0.2 with 0.1 step. For the analysis of flame structure and the flame stabilization mechanism, the simultaneous measurement of PIV/OH PLIF laser diagnostics had been performed. The stabilization point was selected in the most upstream region of the flame base and defined as the point where the turbulent flame propagation velocity was equal to the axial component of local flow velocity. We found that the turbulent flame propagation velocity increased with the decrease of nitrogen mole fraction. We concluded that the turbulent flame propagation velocity was expressed as a function of turbulent intensity and axial strain rate, even though nitrogen diluents mole fraction was changed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 한국추진공학회 2003년도 제20회 춘계학술대회 논문집
• /
• pp.221-224
• /
• 2003

A numerical study is carried out for the detonation wave propagation through a T-branch. The T-branch is a crucial part of the combustion wave igniter, a novel concept of rocket ignition system aimed for the simultaneous ignition of multiple combustion chambers by delivering detonation waves. Euler equation and induction parameter equation are used as governing equations with a reaction term modeled from the chemical kinetics database obtained from a detailed chemistry mechanism. Second-order accurate implicit time integration and third-order space accurate TVD algorithm were used for solution of the coupled equations. Over two-million grid points enabled the capture of the dynamics of the detonation wave propagation including the degeneration and re-initiation phenomena, and some of the design factors were be obtained for the CWI flame tubes.

• The Journal of the Acoustical Society of Korea
• /
• 제16권6호
• /
• pp.100-105
• /
• 1997

To analyze the multipath propagation effects on the source bearing detection of HLA(Horizontal Line Array), the conversion mechanism of the multipath into the bearing is described, and the bearing is estimated from the multipath modeled with typical sound velocity structures of the East and the South Sea of Korea. The erroneous bearing is observed from the beamforming outputs simulated with the modeled multipath, and the erroneous phenomena are analyzed. In case of the East Sea, since the multipath propagation with a high receiving angle occurs due to strong inverse slope of the sound velocity structure, it is possible that the estimated source bearing is different from the real source bearing, and that the number of the source is misrecognized.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• 제36S권6호
• /
• pp.67-75
• /
• 1999

The sensing and communication abilities of a mobile robot are essential to cooperative behavior in distributed autonomous robotic systems. In general, as the number of robot goes on increasing, the limitation of communication capacity and information overflow occur in global communication capacity and information overflow occur in global communication system. Therefore a local communication is more effective than global one. In this paper, we analyze information propagation mechanism based on local communication. To find an optimal communication radius, we propose three methods with different conditions. Also, to avoid chaotic behavior which occurs when a robot obtains and loses information, we find stable condition of information propagation.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제24권12호
• /
• pp.1652-1661
• /
• 2000

A visualization study using the schlieren method is adopted in an optically-accessible, cylindrical constant volume combustion chamber to identify the mechanism of ignition energy and ignition system interaction in spark ignited, lean gasoline-air mixture. In order to research the effects of ignition system on flame propagation, two kinds of ignition system are designed, and several kinds of spark plugs are tested and evaluated. To control the discharge energy, the dwell time is varied. The initial flame development is quantified in terms of 2-D images which provides information about the projected flame area and development velocity as a function of ignition system and discharge energy. The results show that high ignition energy and extended spark plug gap can shorten the combustion duration in lean mixtures. The material, diameter and configuration of electrodes the flame development by changing the transfer efficiency from electrical energy to chemical energy and discharge energy. However these factors do not affect of flame development as much a ignition energy or extended gap does.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.367-368
• /
• 2006

Today, the Artificial Intervertebral Disc (AID) is being developed by increasing the oblique of the endplate gradually. In other words, Ultra-high Molecular Weight Polyethylene (UHMWPE) which is apply to the sliding core of the AID, does not change the shape but alters the oblique of endplate. However, the unreasonable increase of degree of freedom (DOF) can result in the aggravation of the bone fusion and the initial stability and it can also lead to the increase of the concentrated force in core. For these reasons, it is necessary to develop the advanced techniques, which choose the most adequate DOF. In this study, the new optimized modeling of the sliding core and the endplate, the fatigue characteristics, the crack propagation and the formation mechanism of wearing debris was studied and the minimizing technique will be derived from this research.

• Transactions of the Korean Society of Mechanical Engineers
• /
• 제13권1호
• /
• pp.87-95
• /
• 1989

The fatigue crack propagation of random short fiber SMC composite material was investigated. In macroscopic viewpoint, SMC composite material was treated as isotropic material and was analyzed in terms of conventional fracture mechanics. Experiments were conducted on mode I and mixed respectively and various loading level was applied to each mode. Fatigue crack growth can be explained in three steps and most of fatigue life is consumed in initial crack growth. In this experiments, power law, i.e, da/dN=C(C.DELTA.K)$^{m}$ , between fatigue crack growth rate and stress intensity factor range, was valid and the value of the exponent m is about 10, which is much higher than that of other metals. Fracture mechanism was also investigated by SEM fractographic study.