• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1347-1352
• /
• 2001

In this study, the acoustic properties of polyester sound absorbing materials with three different bulk densities were investigated by calculating and measuring the acoustic parameters in terms of characteristic impedance, propagation constant, and absorption coefficient. For the calculations, Delany and Bazley's empirical equation was used together with the experimentally obtained specific flow resistivities under steady flow conditions. For the experimental measurements, the well-known two-thickness method was accessed. The experimentally measured values of characteristic impedance and propagation constant were generally agreed well with the corresponding calculated values. Based on the comparisons between the calculations and measurements, it was found that the magnitude of the absorption coefficient was closely related to the characteristic impedance and the real part of the propagation constant. Especially, the maximum magnitude of the absorption coefficient was depended upon the imaginary part of the propagation constant indicating the phase change of the propagation constant.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.2C
• /
• pp.119-125
• /
• 2011

Start This paper analyzes the propagation characteristics of acoustic signals in indoor environments, which is applicable to indoor positioning system. Indoor stereo sound system is generally valid within $25m^2$. So it is not possible to apply prevalent sound propagation characteristic to indoor positioning system because the prevalent acoustic signals propagation characteristic is defined under free space condition. Therefore, in this paper, we present the propagation characteristics of acoustic signals in indoor environments considering the free space propagation characteristic as well as room characteristic such as humidity, temperature, absorption of atmosphere and so on. To verify the designed propagation model of indoor acoustic signals, this paper presents the propagation characteristics of decreasing sinusoidal signals whose frequencies ate from 1kHz to 20kHz in anechoic room. In addition, this paper also presents the propagation characteristics of decreasing sinusoidal signals which have multiple frequencies.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.3
• /
• pp.224-229
• /
• 2004

In order to control the railway noise, the radiation characteristic of the noise when the train passes by should be analyzed. Generally, the major noise sources of the Korea Train Express are the rolling noise and power unit noise up to 300km/h. In this paper, a train model that is considered to be a row of point sourcesis introduced to analyze the radiation characteristic. The analysis results are compared with the measurement ones. It is shown that the propagation characteristic of the rolling noise is a dipole type and the noise generated by the power unit is radiated as a cosine type. With increasing of the train speed, the noise level at a receiving point is increased in the direction of motion and reduced in the direction opposite to the motion. The analysis results including the moving effect of the noise source at 300km/h show good agreement with the measurement results.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.437-442
• /
• 2005

This paper deals with the measurement and analysis of radio characteristic of 424 MHz for using the automation of transmission and supply of electric power, ana automatic meter reading(AMR). Normally radio propagation characteristic is the base of system design, performance evaluation and choice of position of the base station in wireless communication. It is the most accurate way to design a base station through practical measurements, but it costs much time, money and engineers. So, we developed 424 MHz short range wave propagation model for AMR service.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.10
• /
• pp.1157-1165
• /
• 2012

In this paper, we measure and analyze propagation characteristic of heating, ventilation, and air conditioning(HVAC) ducts within buildings for wireless networks. We analyze the duct structures, implement the feeders exciting propagating modes, and simulate the excitation characteristic. We measure the propagation characteristic of HAVC ducts at 2.45 GHz WiFi band and compare it with that of LOS and partitioned office environments. We propose the design method of wireless network using HVAC ducts based on our results.

• ETRI Journal
• /
• v.34 no.6
• /
• pp.911-921
• /
• 2012

In high-speed wireless communications, an analysis of the propagation characteristics is an important process. Information on the propagation characteristics suitable for each environment significantly helps in the design of mobile communications. This paper presents the analysis results of radio propagation characteristics in outdoor environments for a new mobile wireless system at 781 MHz. To avoid the interference of Korean DTV broadcasting, we measure the channel characteristics in urban, suburban, and rural areas on Jeju Island, Republic of Korea, using a channel sounder and $4{\times}4$ antenna. The path loss (PL) measurement results differ from those of existing propagation models by more than 10 dB. To analyze the frequency characteristics for Korean propagation environments, we derive various propagation characteristic parameters: PL, delay spread, angular spread, and K-factor. Finally, we verify the validity of the measurement results by comparing them with the actual measurement results and 3D ray-tracing simulation results.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.12
• /
• pp.589-595
• /
• 2004

The ESD protection characteristic of chip varistors on a circuit board can not be analyzed by using a conventional circuit simulator due to its microwave characteristic. Thus, by employing Agilent's microwave circuit simulator ADS, we showed that the ESD Protection characteristic or chip varistors can be investigated. order to got more precise simulation results, a chip varistor model was extracted from the electrical characteristic of a TDK's chip varistor and the distributed circuit based pattern was designed as the ESD propagation path. The simulation results showed that the ESD protection characteristic of a chip varistors can be improved drastically by reducing the ESD propagation path.

• Journal of KSNVE
• /
• v.7 no.5
• /
• pp.781-787
• /
• 1997

A new method is presented to determine two fundamental acoustic quantities of sound-absorbing materials such as characteristic impedance and propagation constant. In this study, the surface acoustic impedances of sound-absorbing materials are measured using the impedance tube and the anechoic chamber to determine the above acoustic quantities. The measured results are given for two typical sound-absorbing materials(glass wool and urethane foam) int the frequency range between 150 and 1, 600 Hz. The results are verified by other two known methods, which are Smith & Parrott method and Utsuno et al. method. The absorption coefficients calculated from the empirical models(Miki model for glass wool and Jung model for urethane foam) and two quantities by present method are in good agreement with the measured values.

• Proceedings of the KIEE Conference
• /
• 2001.07a
• /
• pp.467-469
• /
• 2001

This paper presents an efficient location estimation methodology for a partial discharge(PD) source in the power transformer. The methodology previously proposed is not suitable for locating a PD source because the ultrasonic signal with medium attenuated through the inner structure. In general, the propagation characteristic of ultrasonic signal with medium is different. Therefore, using this propagation characteristic, we can detect the location of PD source. In this paper, the proposal algorithm finds the PD source using three sensors attached to one side of the transformer without attenuation of the ultrasonic signal and applying the neural network based geometrical method. The proposed methodology demonstrates the effectiveness and validity on an experimental transformer.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.12
• /
• pp.7-16
• /
• 2020

This study presents an acoustic technique to estimate the hydraulic conductivity of soils. Acoustic attenuation and propagation velocity spectra were measured for dry and saturated sandy specimens to confirm that the relationship between Biot's characteristic frequency and its associated hydraulic conductivity exists only for saturated soils. From the experiments presented in this paper, both attenuation-based and propagation-velocity-based techniques resulted in almost identical characteristic frequencies for saturated soils. The propagation velocity based measurements, however, show a a a slightly clearer trend compared to the attenuation based measurements. The results also show that the acoustically estimated hydraulic conductivities of soils agree well with constant head laboratory test results, demonstrating that this acoustic technique can be a useful nondestructive tool to estimate the hydraulic conductivity of sandy or silty soils.