• 한국정밀공학회지
• /
• 제13권1호
• /
• pp.69-77
• /
• 1996

To design high-effective profile in screw rotor profile using in screw compressor, we design the symmetric type changing the number of lobes and the non-symmetric type changing the neighbourhood of the top point of lobe. Then, we calculated the performance value of profile according to the scale of these non-symmetric's wrap angle. We had the results as follows. 1. About the non-symmetric case, the larger a wrap angle is the shorter seal line is and the smaller blow hole is, thus we know what the large wrap angle profile is better than the small one. 2. We know what the non-symmetric profile is better than the symmetric profile in the result of the compare of seal line's length, blow hole's area, volume curve. 3. About the non-symmetric case, the deformation of the neighbourhood of lobe's top point of the rotor profile has a large effect upon the increase of performance because the length of seal line became short and the area of blow hole is small.

• 산업경영시스템학회지
• /
• 제39권4호
• /
• pp.1-6
• /
• 2016

As manufacturing industries become globalized, product design affects every area of organization. The design sets the goals for a number of different departments, so if it fails to effectively communicate these goals, the entire organization is less efficient. In addition, To communicate clearly, the design must represent a product that meets its technical specification. GD&T (Geometric Dimensioning and Tolerancing) is one of the most important factors, which has an effect on efficiency of manufacture system, in designing products. However, most of designers in different industries are prone to ignore the importance of GD&T. To analyse the importance of GD&T compliance with international standards for design drawing, a comparison analysis of the difference between two methods, composite profile control and multiple single segment profile control, is performed on three different cases and suggests how it used to be more suitable. Composite profile tolerance is specified by a dual feature control frame that has one profile symbol specified with two lines of tolerance information. Whereas a multiple single segment profile control is when two or more single segment profile callouts are used to define the location and/or orientation and/or size and/or form of a part feature. In this study, the following results will be provided : a clear definition and an obvious difference of the tolerance zone, datums and datums sequence and minimization of tolerances. On this study, composite profile tolerance and multiple single segment profile tolerance were discussed. Next steps of research will consist on reaching more accurate results for profile control. Further research will be focused on dealing with the remaining 14 symbols of GD&T.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제34권3호
• /
• pp.180-185
• /
• 2012

Purpose: An accurate preoperative analysis of the patient is essential in orthognathic surgery in order to acquire superior results. In profile, the location of the chin's position may change according to the neck's inclination. This may ultimately affect the amount of surgical movement. During acquisition of cephalometric radiographs, or in supine position, there is a discrepancy in the neck's inclination. This means that there are also various discrepancies between the actual profile and the various preoperative profile images. In the clinical situation, the decision in performing genioplasty usually lies in the analysis of the patient's profile on the operating table at the final stages of orthognathic surgery. This study aims to analyze the different preoperative profile images and to compare their discrepancies. Methods: Fifty eight patients undergoing orthognathic surgery were chosen. These patients were divided into three groups according to angle's classification of malocclusion, as class I, II or III. The right profile of these patients in centric occlusion was taken in natural head position (NHP). This was set as the 'actual profile image.' Another right profile image was taken on the operating table after insertion of the nasotracheal intubation and with muscle relaxants in effect. This was also taken in centric occlusion. The angle (denoted 'A') between the soft tissue glabella-pognion and the true vertical plane was found in the above-mentioned profile images and in the cephalometric radiographs. The differences of these values were analyzed. Results: There were differences in Angle 'A' in all of the preoperative images. These values were however, not statistically significant. Conclusion: In order to gain an esthetic profile during orthognathic surgery, the NHP is shown to be the most reliable position. Images reproducing such head positions should be used in the treatment planning process.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 춘계학술대회 논문집
• /
• pp.27-31
• /
• 1999

Recently, manufacturing industries, specially connected with car are doing their best to increase productivity and to reduce production time. This paper deals with the machining of profile(core/cavity) of mold die using the commercial CAM system. In this study, the effect of machining condition on precision of die profile is investigated by experimental observation and analysis.

• Tribology and Lubricants
• /
• 제16권5호
• /
• pp.357-364
• /
• 2000

In this study, the sliding wear in spur gears, using Archard's wear model, is analyzed. Formulas of tooth sliding wear depth along the line of action are derived. The tooth profile is modified Id make a smooth transmission of the normal loads and the cylinder profile for reducing the pressure spike is suggested. The sliding wear rate is calculated with these profiling results. We expect these modification methods to contribute to the reduction of sliding wear not only in the root, but the tip of tooth and tooth edge.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.184-187
• /
• 2003

The simulation program is developed to get the target strip crown of high strength steel in the continuous hot strip rolling. The developed program consists of several sub-program, which contains work roll shifting pattern, roll wear profile, roll thermal expanded profile and strip profile. Also, the variation of strip profile is investigated according to roll deflection and flattening. The results are compared with the values observed from the actual hot rolling of high strength steel. And effect of bender force on the strip profile is studied. The strip crown is shown to decrease with increasing bender force.

• 한국안전학회지
• /
• 제21권3호
• /
• pp.87-93
• /
• 2006

When a structure is constructed at the site composed of soil, the behavior of a structure is much affected by the characteristics of soil. Therefore, the effect of soil-structure interaction is an important consideration in the design of a structure at the site composed of soil. Precise analysis of soil-structure interaction requires a proper description of soil profile. However, most of approaches are nearly unpractical for soil exhibiting material discontinuity and complex geometry since those cannot consider precisely complicated soil profiles. To overcome these difficulties, an improved integration method is adopted and enables to integrate easily over an element with material discontinuity. As a result the mesh can be generated rapidly and highly structured, leading to regular and precise stiffness matrix. The influence of soil profile on the response is examined by the presented method. It is seen that the presented method can be easily used on soil-structure interaction problems with complicated soil profile and produce reliable results regardless of material discontinuities.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.803-806
• /
• 1995

The vibration and nosic of gears is causeed by manufacting error,alignment error in assembly, and thr meshing stiffness of gears which changes periodically as the meshing of teeth process. On a pair of power transmission helical gears with profile error, the relation between the characteristics of gear vibration and the profile error type have been investigated by simulating the vibrational acceleration level and calculating the natural frequency. The results show that the profile error decrease the natural frequency by reducing the tool stiffness and that the concave error type increase the vibrationsl level. And this paper describes the effect of the tip relief on the vibrational acceleration level which a pair of helical gears with concave error generates.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.55-58
• /
• 2000

SiGe heterojuction bipolar transistors (HBT) have been studied and applied for advanced high speed integrated circuits. Device characteristics of SiGe HBT depending on the Ge profile of the transistor base region have been analysed using a device simulator, ATLAS/BLAZE. The models and parameters have been calibrated to the measured characteristics of the device, having a trapeziodal base profile, including the cut-off frequency of 45GHz and the dc current gain of 200. The Ge concentration which increases linearly, exponentially, or root-functionally from the emitter-base junction to the base-collector junction, has been tried to find out the influence on the device characteristics. The cut-off frequency and gain rather strongly depends on the exponential and root-functional Ge base profiles, respectively.

• 한국치위생학회지
• /
• 제11권6호
• /
• pp.961-971
• /
• 2011

Objectives : The aim of the study was to identify the need of oral health education and prevention? for over 65 years elderly. Methods : his study was to identify the need of oral health management and oral health impact profile among elderly over 65 years. 200 elderly participated in the study, lived in KungBuk and KungNam areas, visited Senior welfare center, from 1st September to 30st December 2008. Results : 1. This majority of respondents are female(74.0%), 75-79 years(29.5%), none education(42.5%), living alone(45.5%), income from children(46.0%), and health insurance(65.5%). 2. In the need of oral health management category, the need of dental treatment are professional toothbrushing, gum treatment, treatment for dental caries, treatment for xerostomia. In the need of prevention and education, the majority participants are 'required'. In oral health impact profile category, the majority participants are 'feel no difficulty during speaking(59.0%)', and 'feel no difficulty during tasting(47.0%)'. In the category, the positive answers are more than negative answers. 3. According to general characteristic with the need of oral health management, famle, obviously income, high level of life are significantly different in the need of prevention and education category. Obviously income is significantly different in the need of dental treatment category. According to general characteristic with the oral health impact profile, getting older, high education are significantly different in disadvantage category. In the case of no spouse, anxiety, physical difficulty, mental difficulty and disadvantage are high score in oral health impact profile. In the case of living alone, pain, anxiety, and disadvantage are high score in oral health impact profile. In the case of no income, limitation of function, pain, anxiety, mental difficulty and disadvantage are high score in oral health impact profile. In the case of no health insurance, anxiety, physical difficulty mental difficulty and lack of sociality are high score in oral health impact profile. 4. The oral health impact profile are positive correlation with the need of dental treatment and the need of prevention education. The effect of oral health impact profile are significantly different with spouse, average of income, the need of prevention education. Conclusions : In Conclusion, the need of prevention education and dental treatment for individual oral health promotion are related with general life condition and life level. Also these are influence of quality of life relate with oral health. These findings are require of development of oral health services program and system from bottom to top.