• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.111-116
• /
• 2001

Waste office paper, photocopied or laser printed, has recently increased along with office automatization. In waste office paper, toner ink is used as the printing medium in place of conventional oil ink. Since toner ink cannot be saponificated by alkali and be decolored by bleaching, different from the case of oil ink, toner remains on regenerated paper as black specks. Although cascade recycling of waste office paper is compelled at present, the demand for low-grade paper is limited. From such circumstances, a new separation process for waste office paper is demanded to achieve parallel recycling. At the first stage of separation studies, the sharpness of separation is evaluated using small separators to obtain fundamental data. In a lab-scale separator, the sample amount of one feed is generally a few grams. However, the sample amount used for brightness, ERIC, and image analysis that are generally used to evaluate the efficiency of deinking are not small for lab-scale tests of these analyses. This paper describes an investigation of a sheet preparation method by a small amount of sample under 0.5g and compares the precision of toner content determination of spectroscopic analysis and image analysis from the viewpoint of separation evaluation. The easiness and convenience of the operation using only general-purpose equipments has also been set as a principle purpose. From the viewpoint of an analysis that yields high precision with a small amount of sample in short time, the method calculating the absorption coefficient from diffuse reflectance in the visible region is the most rational method in this study.

• 한국소음진동공학회논문집
• /
• 제19권12호
• /
• pp.1322-1328
• /
• 2009

This paper presents vibration analysis of maskless exposure module in printed circuit board(PCB) manufacturing system. In order to complete exposure process in PCB, masking type module has been widely used in electronics industries. However, masking process confronts some limitations of application due to higher production cost for masking as well as lower printing resolution. Therefore, maskless exposure module is started to be in the spotlight for flexible production system to meet the needs of fabrication in variable patterns at low cost. Since maskless exposure process adopts direct patterning to PCB, vibration problems become more critical compared to conventional masking type process. Moreover, movements of exposure engine as well as stage generate vibration sources in the system. Thus, it is imperative to analyze the vibration characteristics for the maskless exposure module to improve the quality and accuracy of PCB. In this study, vibration analysis using the finite element analysis is conducted to identify the critical structural parts deteriorating vibration performance. Also, Experimental investigations are conducted by single/dual encoder measurement process under the operating module speed. Measurement points of vibration are selected by three places, which are base of stage, exposure engine and top of stage, to check the effect of vibration from the exposure engine. Comparisons between analysis results and experimental measurement are conducted to confirm the accuracy of analysis results including the developed FE model. Finally, this studies show feasibility of optimal design using the developed FE analysis model.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2010년도 춘계학술대회
• /
• pp.788-791
• /
• 2010

본 논문에서는 인쇄공정기술로써 ETRI $0.8{\mu}m$ CMOS 공정을 사용하여 수동형 인쇄 RFID 태그칩용 64bit ROM을 설계하였다. 먼저 태그 칩의 제작단가를 줄이기 위하여 기존 실리콘 기반의 복잡한 리소그래피 공정을 사용하지 않고 게이트 단자인 폴리 층을 프린팅 기법 중 하나인 임프린트 공정을 사용하여 구현하였다. 그리고 �弼壅� ROM 셀 회로는 기존 ROM 셀 회로의 NMOS 트랜지스터대신에 CMOS 트랜스미션 게이트를 사용함으로써 별도의 BL 프리차지 회로와 BL 감지 증폭기가 필요 없이 출력 버퍼만으로 데이터를 읽어낼 수 있도록 하였다. $0.8{\mu}m$ CMOS 공정을 이용하여 설계된 8 행 ${\times}$ 8 열의 어레이를 갖는 64b ROM의 동작전류는 $9.86{\mu}A$이며 레이아웃 면적은 $311.66{\times}490.59{\mu}m^2$이다.

• 한국전기전자재료학회논문지
• /
• 제33권6호
• /
• pp.465-470
• /
• 2020

Heterolayered K(Ta,Nb)O₃/Pb(Zr,Ti)O₃ thin films on Pt/Ti/SiO₂/Si substrates were prepared by a sol-gel process and spin-coating method. The structural and electrical properties were measured to investigate the possibility of application as an electrocaloric effect device. All specimens exhibited dense and uniform cross-sectional structures without pores, and the average thickness of the specimen coated six times was approximately 394 nm. Curie temperatures were observed at 5℃ or less in type-I and 10℃ in type-II specimens, respectively. Type-II specimens coated 6 times showed a relative dielectric constant of 758 and remanent polarization of 9.71 μC/㎠ at room temperature. The maximum electrocaloric effect occurred between 20 and 25℃, slightly higher than their Curie temperature, and the electrocaloric property (ΔT) of the type-II specimens coated 6 times was approximately 1.2℃ at room temperature.

• Tribology and Lubricants
• /
• 제22권2호
• /
• pp.59-65
• /
• 2006

In hard disk drives as the head to disk spacing continues to decrease to facilitate recording densities, slider disk interactions have become much more severe due to direct contact of head and disk surfaces in both start/stop and flying cases. The slider disk interaction in CSS (contact-start-stop) mode is an important source of particle generation and tribocharge build-up. The tribocharge build-up in the slider disk interface can cause ESD (electrostatic discharge) damage. In turn, ESD can cause severe melting damage to MR or GMR heads. The spindle speed of typical hard disk drives has increased in recent years from 5400 rpm to 15000 rpm and even higher speeds are anticipated in the near future. And the increasing disk velocity leads to increasing disk acceleration and this might affect the tribocharging phenomena of the slider/disk interface. We investigated the tribocurrent/voltage build-up generated in HDD, operating at increasing disk accelerations. In addition, we examined the effects with relative humidity conditions and rest time. We found that the tribocurrent/voltage was generated during pico-slider/disk interaction and its level was about $3\sim16pA$ and $0.1\sim0.3V$, respectively. Tribocurrent/voltage build-up was reduced with increasing disk acceleration. Higher humidity conditions $(75\sim80%)$ produced lower levels tribovoltage/current. Therefore, a higher tribocharge is expected at a lower disk acceleration and lower relative humidity condition. Rest time affected the charge build-up at the slider-disk interface. The degree of tribocharge build-up increased with increasing rest time.

• 공업화학
• /
• 제29권6호
• /
• pp.782-788
• /
• 2018

서브 미크론 구리-은 코어-쉘 Cu@Ag 입자를 초음파화학과 결합된 금속교환 반응으로 합성하고 인쇄용 전자부품을 위한 저렴한 전도성 페이스트 적용을 평가하였다. 코어-쉘의 합성을 위한 반응에서 코어로 사용된 $Cu_2O/Cu$ 복합체의 $Cu_2O$는 초음파화학 반응으로 Cu로 환원되고 Cu 원자는 Ag의 금속교환 반응의 환원제로 작용하여 코어 표면에 Ag가 코팅된 코어-쉘 구조를 얻었다. TEM-EDS와 TG-DSC를 이용하여 서브 미크론 입자의 코어-쉘 구조를 확인하였다. 70 wt% Cu@Ag를 용매에 분산시킨 전도성 페이스트를 결합제와 습윤제를 사용하여 제조하고, 스크린 인쇄법을 사용하여 폴리아미드 필름상에 코팅하였다. Ag 함량이 8 at%와 16 at%인 Cu@Ag 입자를 함유하는 인쇄된 페이스트 필름은 공기 중의 $180^{\circ}C$에서 소결한 후 각각 96.2와 $38.4{\mu}{\Omega}cm$의 낮은 비저항 값을 나타내었다.

• 전기전자학회논문지
• /
• 제25권2호
• /
• pp.322-329
• /
• 2021

본 연구에서는 열처리 후 Island 표면 구조를 가지는 고분자 Poly(vinylidenefluoride-co-trifluoroethylene) [P(VDF-TrFE)]를 사용하여 유기 발광 다이오드의 광추출 효율을 향상시키기 위한 방법을 제시하였다. Island 구조의 P(VDF-TrFE) 표면 위에 임프린트한 polydimethylsiloxane (PDMS)는 Spike 구조를 띄고 이를 통해 전류 및 외부양자 효율을 약 20%을 향상시켰다. 제작된 필름은 8.2의 낮은 Haze특성을 보이며, 93.4% 우수한 투과도 특성으로 인해 Pixel blur 없이 광효율을 향상시킬 수 있음을 확인하였다.

• 전기전자학회논문지
• /
• 제26권2호
• /
• pp.205-210
• /
• 2022

본 연구에서는 유기 발광 다이오드(OLED)의 광추출 향상을 위한 롤투롤 마이크로컨택(mCP)방식으로 인쇄된 마이크로렌즈 어레이(MLA)를 제시하였다. 상업적으로 사용되는 마이크로렌즈 어레이를 템플레이트로 사용하여서 polydimethylpolysiloxane(PDMS)를 롤스탬프로 제작하였다. 낮은 끓는 점을 가지는 불소화 잉크로부터 PDMS 롤스탬프에 고분자 박막을 형성하고 이를 OLED의 하부면에 고압·고온 처리 없이 인쇄하였다. 최적화된 농도를 찾아서 템플레이트로 사용된 MLA와 거의 동일한 모양의 패턴을 성공적으로 인쇄하였다. 마이크로컨택 방식으로 인쇄된 MLA의 구조와 소재의 낮은 흡수도로 인해서 OLED의 외부양자효율이 18% 향상되었다.

• 한국수소및신에너지학회논문집
• /
• 제34권1호
• /
• pp.8-16
• /
• 2023

In this work, we report basic performance test results of a lab-scale three phase alternative current (AC) arc plasma torch system for plasma gas reforming applications. The suggested system primarily consists of three graphite electrodes inclined at 12.5° to the central axis, a 𝞥 150 mm cylindrical gas path and a three phase-60 Hz AC power supply. At air flow rate of 50 Lpm and arc currents of 100-175 A, test results revealed that plasma resistances were decreasing from 1.08 Ω to 0.53 Ω with the increase of plasma power from 9.3 kW to 13.8 kW, causing the decrease of power factor and increase of the line voltages. However, the injected air can be heated quickly up to the temperatures of >1,200℃ when injecting AC arc plasma powers of >10 kW.

• 한국전기전자재료학회논문지
• /
• 제36권6호
• /
• pp.588-593
• /
• 2023

The advantage of OTFT technology is that large-area circuits can be manufactured on flexible substrates using a low-cost solution process such as inkjet printing. Compared to silicon-based inorganic semiconductor processes, the process temperature is lower and the process time is shorter, so it can be widely applied to fields that do not require high electron mobility. Materials that have utility as electrode materials include carbon that can be solution-processed, transparent carbon thin films, and metallic nanoparticles, etc. are being studied. Recently, a technology has been developed to facilitate charge injection by coating the surface of the Al electrode with solution-processable titanium oxide (TiOx), which can greatly improve the performance of OTFT. In order to commercialize OTFT technology, an appropriate method is to use a complementary circuit with excellent reliability and stability. For this, insulators and channel semiconductors using organic materials must have stability in the air. In this study, carbon-doped Mo (MoC) thin films were fabricated with different graphite target power densities via unbalanced magnetron sputtering (UBM). The influence of graphite target power density on the structural, surface area, physical, and electrical properties of MoC films was investigated. MoC thin films deposited by the unbalanced magnetron sputtering method exhibited a smooth and uniform surface. However, as the graphite target power density increased, the rms surface roughness of the MoC film increased, and the hardness and elastic modulus of the MoC thin film increased. Additionally, as the graphite target power density increased, the resistivity value of the MoC film increased. In the performance of an organic thin film transistor using a MoC gate electrode, the carrier mobility, threshold voltage, and drain current on/off ratio (I_on/I_off) showed 0.15 cm²/V·s, -5.6 V, and 7.5×10⁴, respectively.