• Journal of Chest Surgery
• /
• v.33 no.2
• /
• pp.117-124
• /
• 2000

Background: Nucleoside transport inhibitor(NTI) Keeps AMP, ADP, ATP levels high in myocytes by inhibiting adenosine cataboilsm so that it may preserve the myocardial contractability during ischemia In this study we investigated the effects of cyclic AMP phosphodiesterase inhibor(C-AMP PDSI) and S-P-nitrobenzyl-6 -thioniosine(NBT; a sort of NIT) on myocadial preservation and changes of constituent enzyme. Material and method: Twenty-six isolated rabbit hearts were perfused with Krebs-Henseleit buffer solution for 20 minutes arrested for 20 minutes and ten reperfused for 30 minutes. The following four groups were prepared and hemodynamic changes coronary effluent lactate dehydrogenase (LDH) a-hydroxybutylic accid(a-HBD) levels and myocardial LDH creatine kinase-MB (CK-MB) adenosine deaminase(ADA) a-HBD levels and myocardial LDH creatine kinase-MB (CK-MB) adenosine deaminase(ADA) a-HBD levels were analysed before and after cardiac arest ; Group I(control) ; the heart was only perfused with K-H ; Group II ; the heart was perfused with K-H including C-AMP PDSI(Amrinone 25mg/L); Group III ; the heart was perfused with K-H including NBT(4.19mg/L) ; Group IV ; the heart was perfused with K-H including C-AMP PDSI + NBT. Result : Left venticular developed pressure(LVDP) at 10 minutes of the equilibrium was significantly higher in group III(72.1$\pm$5.3 mmHg p<0.01) and group III(72$\pm$5.6 mmHg P<0.025) as compared with group I (40.8$\pm$4.7mmHg) and LVDP at 20 minutes of the reperfusion was significantly higher in group II(74$\pm$5.3mmHg p<0.01) and group III(72$\pm$5.6mmHg p<0.025) as compared with group I (44.2$\pm$4.6mmHg). Percentage recovery of LVDP at the reperfusion was the highest in group II(123.3%) Percentage recovery of coronary flow at the equilibrium reperfusion were higher in group II(310%, 270%) group III(230%, 290%) group IV(310%, 280%) as compared with group I (100%) respectively. Myocadial LDH level was significant lower in group IV(33495$\pm$1802 IU/gm p<0.04) as compared with group I(48767$\pm$1421 IU/gm) Myocadial CK-MB level was significant higher in group II(74820$\pm$1421 IU/gm) compared with group I (45450$\pm$1737 IU/gm) Myocadial ADA level was significant higher group IV(1215$\pm$8 IU/gm p<0.05) compared with group I(125$\pm$15 IU/gm) but there was no significant difference between group I and group II ,III, IV in changes of coronary effluent LDH, a-HBD levels. Conclusion: C-AMP PDSI solely appears to have a better effect on myocardial preservation after ischemia than NBT but with no synergistic effect and it could keep CK-MB leve high in myocardial tissues.

• Journal of Chest Surgery
• /
• v.42 no.6
• /
• pp.744-748
• /
• 2009

Background: This study was designed to determine etiologic factors for iatrogenic pneumothorax in an era of in-creased use of invasive procedures and to evaluate its impact on morbidity. Material and Method: Subjects were 112 patients (65 men and 47 women ranging in age from 20 to 90 years) who were diagnosed with an iatrogenic pneumothorax between January 2005 and December 2008. We reviewed medical records retrospectively. Result: The leading causes of iatrogenic pneumothorax were percutaneous needle aspiration (50), central venous catheterization (29), acupuncture (14), thoracentesis (8) and positive pressure ventilation (7). The majority of the patients (60 of 114) were treated with chest tubes. The mean duration of hospital treatment was 5.8 $({\pm}4.0)$ days. Hospitalization was prolonged in 24 patients (21.1%). No patient died from iatrogenic pneumothorax. Conclusion: In our study, the most common cause of Iatrogenic pneumothorax was percutaneous needle aspiration. The mortality and morbidity from iatrogenic pneumothorax is not significant. The recognition of pneumothorax, depends on careful examination after completion of an invasive procedure, and should be followed by prompt and definitive therapy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.220-220
• /
• 2013

Surface-normal transmission electro-absorption modulator (EAM) are attractive for high-definition (HD) three-dimensional (3D) imaging application due to its features such as small system volume and simple epitaxial structure [1,2]. However, EAM in order to be used for HD 3D imaging system requires uniform modulation performance over large area. To achieve highly uniform modulation performance of EAM at the operating wavelength of 850 nm, it is extremely important to remove the GaAs substrate over large area since GaAs material has high absorption coefficient below 870 nm which corresponds to band-edge energy of GaAs (1.424 eV). In this study, we propose and experimentally demonstrate a transmission EAM in which highly selective backside etching methods which include lapping, dry etching and wet etching is carried out to remove the GaAs substrate for achieving highly uniform modulation performance. First, lapping process on GaAs substrate was carried out for different lapping speeds (5 rpm, 7 rpm, 10 rpm) and the thickness was measured over different areas of surface. For a lapping speed of 5 rpm, a highly uniform surface over a large area ($2{\times}1\;mm^2$) was obtained. Second, optimization of inductive coupled plasma-reactive ion etching (ICP-RIE) was carried out to achieve anisotropy and high etch rate. The dry etching carried out using a gas mixture of SiCl4 and Ar, each having a flow rate of 10 sccm and 40 sccm, respectively with an RF power of 50 W, ICP power of 400 W and chamber pressure of 2 mTorr was the optimum etching condition. Last, the rest of GaAs substrate was successfully removed by highly selective backside wet etching with pH adjusted solution of citric acid and hydrogen peroxide. Citric acid/hydrogen peroxide etching solution having a volume ratio of 5:1 was the best etching condition which provides not only high selectivity of 235:1 between GaAs and AlAs but also good etching profile [3]. The fabricated transmission EAM array have an amplitude modulation of more than 50% at the bias voltage of -9 V and maintains high uniformity of >90% over large area ($2{\times}1\;mm^2$). These results show that the fabricated transmission EAM with substrate removed is an excellent candidate to be used as an optical shutter for HD 3D imaging application.

• Journal of Biomedical Engineering Research
• /
• v.24 no.6 s.81
• /
• pp.515-522
• /
• 2003

Pharynx is a system transporting foods by peristaltic motion(contraction and expansion movement! into the esophagus and functioning as airway passages. In this study, structural changes of pharyngeal dysfunction are analyzed by biomechanical model using CT and FEM(finite clement method). Loading condition was assumed that equal pressure was loaded sequentially to inside of pharyngeal tissue. In order to analyze the pharyngeal muscular dysfunction by biomechanical model. the pharyngeal dysfunctions was classified into 3 cases. Taking into account the clinical complication by neuromuscular symptoms such as pharyngeal dysfunction after stroke. we assumed that a change of material property is caused by muscular tissue stiffness. A deformation of cross sectional area of the pharynx is analyzed increasing the stiffness $25\%,\;50\%,\;75\%$ in each case on the basis of stress-strain relationship. Based on three-dimensional reconstruction of pharyngeal structure using limited factor - techniques and the optimization procedure by means of inverse dynamic approach. the biomechanical model of the human pharynx is implemented. The results may be used as clinical index illustrating the degree of pharyngeal muscular dysfunction. This study may be used as useful diagnostic model in discovering early deglutitory impediment caused by physiological or pathological pharyngeal dysfunction.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.736-741
• /
• 2017

This paper examines the design for improving the wiper system of rotorcraft. During rotorcraft operation, the wiping performance and excessive clearance can decrease. The wiper system consists of a wiper arm assembly, motor, convertor and flex drive. If there is a problem with the wiper system, the operation ability decreases because the operation is restricted in a rainy environment. There are two main causes of the problem of the wiper system: the lifting forces acting on the wiper arm in aircraft flight and the excessive gap of the components. To remedy these two problems, the wiper arm was improved. The improvements included increased contact pressure on the wiper arm (spring tension), improved gear clearance, and material and shape changes. Durability test, aircraft ground test and flight test were carried out to verify the improved shape, and it was confirmed that the wiping performance and clearance problems were solved. Currently, the rotorcraft is operated without problem by applying the improved shape, and this design improvement process will be a useful reference for future rotorcraft development.

• Resources Recycling
• /
• v.21 no.1
• /
• pp.60-65
• /
• 2012

The Ti-6Al-4V alloys were prepared by recycling of dental Ti pure scraps using vacuum arc melting process, and their physical properties were evaluated the Ti-6Al-4V alloys with different oxygen concentrations. For the preparation of Ti-6Al-4V alloys, Ti pure scraps used for dental implant were utilized as a raw material, and their different oxygen concentrations were ranged from G1 to G4 grade in ASTM standards. It was confirmed that the weight loss of Al in the composition of Ti-6Al-4V alloy could be controlled under the Ar pressure of 875 torr during the melting of alloy. The oxygen concentrations of the Ti-6Al-4V alloys were ranged from 1170 to 3340 ppm. The vickers hardness change of the Ti-6Al-4V alloys showed a similar behavior with that of pure Ti. As a result, we confirmed a possibility of preparation of Ti-6Al-4V alloy by recycling of dental Ti scraps using vacuum arc melting process in this study.

• Journal of Sericultural and Entomological Science
• /
• v.53 no.2
• /
• pp.92-96
• /
• 2015

It is known that silk protein supports effectively proliferation of cell such as insect cell and hybridoma cell. Although there are many varieties of Bombyx mori silkworm, the effect of silkworm varieties on cell proliferation has not been considered in detail. We studied that characteristics of silk cocoon obtained from Baegokjam, Kumokjam, Daeseongjam silkworm varieties and whether silk protein affected cell proliferation or not. Silk sericin was prepared under high temperature and high pressure condition. Silk fibroin was prepared using $CaCl_2:H_2O:EtOH$ with different dissolution time. As a result, there are differences in silk cocoon from different silkworm varieties about cell proliferation. The proliferation was accelerated in the presence of Baegokjam silk sericin and Kumokjam silk fibroin with 5hr dissolution time. We expect that silk proteins could be a preferable culture medium supplement for stimulating the proliferation of cell. Then, this results suggest silk as a new material for medium supplement replacing with fetal bovine serum.

• Nuclear Engineering and Technology
• /
• v.53 no.10
• /
• pp.3367-3378
• /
• 2021

The design phase and safety assessment of Generation IV liquid metal-cooled fast reactors calls for the improvement of fuel pin performance codes, in particular the enhancement of their predictive capabilities towards uranium-plutonium mixed oxide fuels and stainless-steel cladding under irradiation in fast reactor environments. To this end, the current capabilities of fuel performance codes must be critically assessed against experimental data from available irradiation experiments. This work is devoted to the assessment of three European fuel performance codes, namely GERMINAL, MACROS and TRANSURANUS, against the irradiation of two fuel pins selected from the SUPERFACT-1 experimental campaign. The pins are characterized by a low enrichment (~ 2 wt.%) of minor actinides (neptunium and americium) in the fuel, and by plutonium content and cladding material in line with design choices envisaged for liquid metal-cooled Generation IV reactor fuels. The predictions of the codes are compared to several experimental measurements, allowing the identification of the current code capabilities in predicting fuel restructuring, cladding deformation, redistribution of actinides and volatile fission products. The integral assessment against experimental data is complemented by a code-to-code benchmark focused on the evolution of quantities of engineering interest over time. The benchmark analysis points out the differences in the code predictions of fuel central temperature, fuel-cladding gap width, cladding outer radius, pin internal pressure and fission gas release and suggests potential modelling development paths towards an improved description of the fuel pin behaviour in fast reactor irradiation conditions.

• Journal of the Korea Society of Computer and Information
• /
• v.26 no.10
• /
• pp.125-137
• /
• 2021

This study was intended to develop a prototype of new Hanbok Cheollik one-piece based on design extracted through a preference survey on new Hanbok Cheollik one-piece. Through this, it was intended to provide information on patterns that are fundamental to the production of new Hanbok Cheollik one piece. The pattern of the experiment was produced by modifying D pattern, which was selected as excellent in the comparison of commercial Cheollik one-piece patterns. The SPSS 26.0 program was used to analyze the appearance evaluation of patterns. As a result of the 1^st evaluation of appearance and garment pressure, the shoulder, sleeve length, skirt length and sleeve width required modification, reducing the sleeve length by 8.0cm and the sleeve width by 1.0cm in total. The length of the skirt was reduced by 5.0cm and the shoulder end point was reduced by 0.5cm on both sides to modify the shoulder width. As a result of the 2^nd evaluation, the waist area, sleeve width, and skirt wrinkles were required to be corrected, reducing 2.0 cm waist width and 1.0 cm sleeve width and removing wrinkles on the front center and side area. The final pattern was highly appreciated. In future studies, it is thought that research should be conducted through study of Cheollik one-piece pattern according to material and age and the actual wearing experiment according to fabric and age.

• Food Engineering Progress
• /
• v.15 no.4
• /
• pp.398-403
• /
• 2011

A dielectric barrier discharge plasma (DBDP) treatment system was fabricated and the optimum operating conditions for the plasma generation were determined in order to explore the potential of cold plasma as a non-thermal proessing technology. The microbial inactivation performance of the system was also evaluated against Staphyloocus aureus. The system consisted of power supply, transformer, electrode assembly and sample treatment plate. The input power was 220 V single phase AC and amplified to 10.0-50.0 kV on a transformer. A pulsed sine wave of frequency 10.0-50.0 kHz was introduced to the electrode embedded in ceramic as a dielectric barrier material in order to generate plasma at atmospheric pressure. Higher currents and consequently greater power were required for the plasma generation as the frequencies increased. A homogeneous and stable plasma was generated at currents of 1.0-2.0, and frequencies of 32.0-35.3 kHz. The optimum electrode-gaps for the plasma generation were 1.85 mm without loaded samples. More power was consumed as the electrode-gaps increased. The practically optimum electrode- gap was, however, 2.65 mm when samples were treated on slide-glasses for microbial inactivation. The maximum temperature increase after 10 min treatment was less than 20$^{\circ}C$, indicating no microbial inactivation effect by heat and thereby insuring a non-thermal method. The DBDP inactivation effect against Staphyloocus aureus increased linearly with treatment time up to 5 min, but plateaued afterward. More than 5 log reduction was achieved by 10 min treatment at 1.25 A.