• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.32-38
• /
• 2006

A clutch hydraulic system for automotive manual transmissions transfers hydraulic pressure generated by driver's pedal manipulation to the clutch mechanism. The foot effort when the clutch pedal is pushed is different than that when the clutch is returned. The effort or load difference, called hysteresis, is caused by the friction produced between rubber seal and inner wall inside the hydraulic cylinder. This clutch pedal travel foot effort hysteresis is essential for a clutch hydraulic system design and analysis. The dynamic model for a clutch hydraulic system is developed and a simulation analysis is performed to estimate the fiction coefficient as a function of the cylinder pressure. The simulation result is then compared to the measurements obtained from a clutch hydraulic system tester to ensure the reliability of the dynamic model and the coefficients estimated. Also the estimated friction coefficients at various pressure values are compared to those reported by an independent study.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1598-1603
• /
• 2004

This paper is an experimental study on the performance characteristic with a variation of capillary diameter and length. The performance characteristic of a refrigeration system is predicted that it is occurring changes of flow pattern and pressure drop in a capillary tube because of reduction of capillary diameter 0.74 to 0.6 mm. The difference between experimental results and analytical results is mainly caused by values of friction factor for using to calculate pressure drop through a small diameter capillary tube under 0.74mm. The experimental equation is derived from capillary tube test data using curve fitting method.

• Korea-Australia Rheology Journal
• /
• v.16 no.3
• /
• pp.129-134
• /
• 2004

The aggregation characteristics of red blood cells (RBCs) were measured using a newly developed light-transmission slit rheometer. Conventional methods of RBC disaggregation such as the rotational Couette system were replaced with a pressure-driven slit flow system with a vibrational mechanism. Using a vibration generator, one can disaggregate the RBC aggregates stored in the slit. While shear stress decreases exponentially, instantaneous pressure and the transmitted light intensity were measured over time. Applying an abrupt shearing flow after disaggregation caused a rapid elongation of the RBCs followed by loss of elongation with the decreasing shear stress. While the shear stress is further decreasing, the RBCs start to re-aggregate and the corresponding transmitted intensity increases with time, from which the aggregation indices can be obtained using a curve-fitting program.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.27 no.1
• /
• pp.59-71
• /
• 2009

Measuring ink penetration is one of the best ways to know paper printability. Ink penetration was effected by physical properties of newsprint paper. This study was carried out for the purpose of improvement printability with ink penetration of domestic newsprint paper. The samples were prepared by means of 20 newsprint paper manufacture company in Korea, and were tested by IGT printability tester. The results of this experiments showed that the depth of ink penetration according to the printing pressure. The maximum points in ink transfer curve and the coefficients of oil absorption of the papers also depend mainly upon the situation of anchor points.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.3
• /
• pp.3872-3877
• /
• 1975

This study was conducted to examine the effects of the change of cap hole diameter and pressure on the travelling distance and the sprayed particle size for the medium range nozzle. The results of this study are summarized as follows; 1) The effective travelling distance was about from 1 meter to 8 meters and centro-position of the travelling distance was about 3 or 5 meters. 2) Main effect of change of cap hole diameter for the travelling distance was a slight convex quadratic curve. 3) Main effect of change of pressure increased linearly, its increasing rate about 1.6 was large. 4) Sizes of sprayed particles were less than 250${\mu}$ generally and the sizes decreased according to the increasing of travelling distance. 5) Changes of diameter of sprayed particles by cap hole diameter increased in accordance with increasing of cap hole diameter. 6) Changes of diameter of sprayed particles by the groove depth of swirl plate was very slight.

• Transactions of the Korean hydrogen and new energy society
• /
• v.19 no.1
• /
• pp.26-34
• /
• 2008

This study presents an aerodynamic design and an experimental performance test of a turbo air compressor consisted of mixed-flow impeller and curved diffuser for the PEM fuel cell vehicle application. Many studies compare the efficiency, cost or noise level of high-pressure and low-pressure operation of PEM fuel cell systems. Pressure ratio 2.2:1 is considered as design target The goal of compressor design is to enlarge the flow margin of compressor from surge to choke mass flow rate to cover the operational envelope of FCV. Large-scale rig test is performed to evaluate the compressor performance and to compare the effects of compressor exit pipe volume to stall or surge characteristics. The results show that the mixed-flow compressor designed has large flow margin, and the flow margin of compressor configuration with small exit volume is larger than that with large exit volume.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.6
• /
• pp.52-63
• /
• 1997

Non-circular gear has a good velocity ratio in high speed and heavy load without any slip, moreover, it can transmit various motion, using simpler structure than link and cam, automation mechainism. In case of designing and manufacturing non-circular gear. I suggest one of references in applying non-circular gear to industrial plant, and suitable range of application by pressure angle curvature and angle ratio

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1491-1494
• /
• 2003

A specific experimental method, the Split Hopkinson Pressure Bar (SHPB) technique has been widely used to determine the dynamic material properties under the impact compressive loading conditions with strain-rate of the order of 103/s∼104/s. This type of test procedure has been used to examine the dynamic response of materials in various modes of testing. In this paper, dynamic deformation behaviors of rubber materials widely used for the isolation of vibration from varying structures under dynamic loading are determined using a Split Hopkinson Pressure Bar technique.

• Korean Journal of Pharmacognosy
• /
• v.8 no.2
• /
• pp.55-60
• /
• 1977

In this study the effect of water extract of Viticis rotundifoliae Fructus(VRE) on the blood pressure of the rabbit was investigated. The results of the experiment are as follows. 1. VRE produced a fall of blood pressure, exhibiting dose-action curve in the rabbit. 2. The depressor effect of VRE was inhibited by atropine and chlorisondamine, potentiated by physostigmine, and then potentiated slightly by bethanidine. 3. Effect of VRE was not influenced by propranolol and cyproheptadin. The above results indicate that hypotension of VRE is produced by stimulation of parasympathetic nervous system induced centrally.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.153-158
• /
• 2000

Nuclear reactor pressure vessel should be safety even in the case that hypothetical defects with allowable size are in vessel. Therefore, the materials should have excellent fracture resistance characteristics. The purpose of this study is to analyze the results of preirradiation baseline test of nuclear pressure vessel for Yonggwang Unit 5/6. In experiments, drop weight tests and impact tests are carried out to obtain nil-ductility transition reference temperature, $RT_{NDT}$ and static and dynamic fracture toughness tests are performed to compare with $K_{IR}$ curve in accordance with ASME Sec.III. The test results show that the materials had sufficiently fracture resistance characteristics for 40 years of design life.