• Environmental Engineering Research
• /
• v.19 no.3
• /
• pp.205-214
• /
• 2014

Petroleum a vital commodity affecting every aspect of 21st century. Toxicity and adverse effects of sulphur as catalyst in petroleum products is of great concern required development of techniques for desulphurization in compliance with the International standards. Installation of desulphurizing units costs over $200 million per unit placing economic burden on developing countries like Pakistan. Present study analysis of commercial fuels (station petrol and jet fuel JP8) on gas chromatography-mass spectrometry (GC-MS) identified sulphur concentration of 19.94 mg/L and 21.75 mg/L, respectively. This scenario urged the researcher to attempt synthesis of material that is likely to offer good adsorption capacity for sulphur. Following protocol of sol-gel method, transition metals (Ni, Cu, Zn) solution is gelated with tetraethoxysilane (TEOS; silica precursor) using glycerol. Fourier transform infrared spectroscopy (FTIR) spectra revealed bonding of Zn-O, Cu-O, and Ni-O by stretching vibrations at $468cm^{-1}$, $617cm^{-1}$, and $468cm^{-1}$, respectively. Thiophene and Benzothiophene mixed in n-heptane and benzene (4:1) for preparation of Model Fuels I and II, respectively. Each of silica based metal was applied as adsorbent in batch mode to assess the removal efficiency. Results demonstrated optimal desulphurization of more than 90% following efficacy order as Si-Ni > Si-Zn > Si-Cu based adsorbents. Proposed multilayered (Freundlich) adsorption mechanism follows ${\pi}$-complexation with pseudo secnd order kinetics.

• Analytical Science and Technology
• /
• v.10 no.1
• /
• pp.31-34
• /
• 1997

Barium titanyl oxalate which is a precursor of barium titanate has been precipitated at pH 4~5 by a rapid addition of aqueous titanyl oxalate solution to artificial environmental water samples containing equivalent weight of $Ba^{2+}$ ions. Quantitative recoveries of $Cd^{2+}$ and $Pb^{2+}$ from the water samples has been confirmed and found to be usable as a possible method of preconcentration for their determination.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.107-110
• /
• 1999

The ultrasonic spray method was employed to make (Y,Gd)BO$_3$:Eu Phosphor, and its optical properties under 147nm VUV and 254 nm UV excitations were characterized and then compared with that produced by the solid-state reaction. The mixed solution of acetate hydrates of Y, Gd, Eu and boric acid diluted in water or methanol was used as the precursor fur the spray. It was found that (Y,Gd)BO$_3$:Eu phosphor made by this ultrasonic spray had a spherical shape and fine particle size of 1${\mu}{\textrm}{m}$. The crystalline structure for the as-sprayed phosphor was amorphous, but it converted into the same polycrystalline phase of solid state reaction after post heat treatment at 110$0^{\circ}C$ for 2hr. The emitting intensity under VUV and UV excitations for the spray-formed (Y,Gd)BO$_3$:Eu phosphor, however, was inferior to the later one. The excitation spectra were also studied and compared under VUV and UV excitations to explain the change of emitting intensity with Gd substitution in (Y$_{1-x}$ Gd$_{x}$)BO$_3$:Eu Phosphors made by spray and solid state reaction.on.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.288-289
• /
• 2006

We studied the effect of sol-gel processing and sintering temperature on the microwave properties of $MgCo_2(VO_4)_2$ system(MCV) which is applicable to LTCC(low-temperature cofired ceramics). The MCV was synthesized by sol-gel process using solution that contains precursor molecules for Mg, Co, and V. SEM analysis shows that the average particle size is ${\sim}1{\mu}m$ and size distribution is very uniform compared to the one prepared by conventional solid-state reaction process. Highly dense samples were obtained at the sintering temperature range of $750^{\circ}C{\sim}930^{\circ}C$. The maximum $Q{\times}f_0$ value of 55,700GHz, dielectric constant(${\varepsilon}_r$) of 10.41 and temperature coefficient(${\tau}_f$) of $-85ppm/^{\circ}C$ was obtained at the sintering temperature of $930^{\circ}C$. The superior microwave properties of sol-gel processed MCV relative to conventional solid-state reaction processed one is remarkable especially at lower sintering temperatures such as $750^{\circ}C$ and $800^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.66-66
• /
• 2007

Lead zirconate titanate (PZT) is one of the most attractive perovskite-type materials for ferroelectric random access memory (FRAM) due to its higher remanant polarization and the ability to withstand higher coercive fields. We first applied the damascene process using chemical mechanical polishing (CMP) to fabricate the PZT thin film capacitor to solve the problems of plasma etching including low etching profile and ion charging. The $0.8{\times}0.8\;{\mu}m$ square patterns of silicon dioxide on Pt/Ti/$SiO_2$/Si substrate were coated by sol-gel method with the precursor solution of PZT. Damascene process by CMP was performed to pattern the PZT thin film with the vertical sidewall and no plasma damage. The polarization-voltage (P-V) characteristics of PZT capacitors and the current-voltage characteristics (I-V) were examined by change of process parameters. To examine the CMP induced damage to PZT capacitor, the domain structure of the polished PZT thin film was also investigated by piezoresponse force microscopy (PFM).

• Journal of the Korean Vacuum Society
• /
• v.20 no.3
• /
• pp.189-194
• /
• 2011

Si-cell was prepared with various types owing to the etching times textured by the KOH etching solution. The pn junction for solar cell was prepared on p-type Si wafer by the furnace using the $POCl_3$ and oxygen mixed precursor, and the metalization was done using by the Al back electrode and Ag front electrode. Textured Si surface was etched by the pyramid formation. The efficiency and the fill factor was increased in the Si-cell with a large size of pyramids, because of the series resistances decrease depending on the increasing of the photon absorbance. Increasing of the absorbance occurred the induction of the short current and open voltage, and then the efficiency was increased.

• Korean Journal of Materials Research
• /
• v.15 no.11
• /
• pp.690-696
• /
• 2005

The ultrastructure ore of a nanostructured apatite film nucleated from solution was studied to gain insights into that of bone minerals which is the most important constituent to sustain the strength of bones. Needle-shaped apatite crystal plates with a bimodal size distribution $(\~100\;to\;\~1000 nm)$ were randomly distributed and they were found to grow parallel to the c-axis ([002]), driven by the reduction of surface energy. Between these randomly distributed needle-shaped apatite crystals which are parallel to the film, apatite crystals (20-40nm) with the normal of the grains quasi-perpendicular to the c-axis were observed. These observations suggest that the apatite film is the interwoven structure of apatite crystals with the c-axis parallel and quasi-perpendicular to the fan. In some regions, amorphous calcium phosphate, which is a precursor of apatite, was also observed. In the amorphous phase, small crystalline particle with the size of 2-3 nm were observed. These particles were quite similar, in size and shape, to those observed in the femoral trabecular bone, suggesting the nucleation of apatites by a biomimetic process in vitro is similar to that in vivo.

• Journal of Radiation Industry
• /
• v.5 no.3
• /
• pp.249-252
• /
• 2011

Lignin is one of the natural macromolecules. Every year large amount of lignin arises from the cellulose production as a by-product worldwide. The use of lignin as a precursor to carbonaceous materials has gained interest due to its low cost and high availability. Therefore, we improved the properties of alkali-lignin by exposing to gamma ray in this study. The alkali-lignin is irradiated by Gamma ray irradiation with varying doses. The char yields of alkali-lignin were investigated by increasing up to 50 kGy. The cross-linking and bond scission of alkali-lignin occur simultaneously during gamma ray irradiation. The crosslinking was predominantly accelerated by gamma ray irradiation up to 50 kGy. Bond scission predominantly occurs between 50 and 500 kGy. ESCA analysis indicated that the alcoholic carbon increase up to 50 kGy. Solution viscosity was increased as absorbed dose increased up to 20 kGy. In addition, the aromatic ring was not influenced by irradiation at doses ranging from 20 to 500 kGy as shown in FT-IR results.

• Corrosion Science and Technology
• /
• v.18 no.5
• /
• pp.168-174
• /
• 2019

The sol-gel methodology has been applied successfully in the synthesis of a novel hybrid coating based on dimethoxymethyl-n-octadecylsilane precursor. The newly synthesized parent coating was functionalized further with two commercially-available corrosion-inhibitive pigments Moly-$white^{(R)}$ 101-ED and Hfucophos $Zapp^{(R)}$, applied to mild steel panels, and immersed continuously in 3.5% NaCl electrolytic solution for 288 h. The corrosion protection performance of the prepared functional coatings was evaluated using electrochemical impedance spectroscopy (EIS) and DC polarization techniques. An enhancement in the barrier properties has been revealed from the electrochemical characterization data of the hybrid films, in comparison with untreated mild steel substrates following long-term immersion in 3.5% NaCl. The corrosion resistance properties of the newly developed coatings over mild steel substrates found to be largely dependent on the type of the loaded inhibitive pigment in which the Moly-white inhibitor has a positive impact on the corrosion protection performance of the parent coating, while an opposite behavior was observed upon mixing the base polymeric matrix with the commercially-available Zapp corrosion inhibitor.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.109-112
• /
• 2008

A performance of micro thruster was measured with catalyst bed that was prepared by different catalyst loading condition for the optimization of catalyst bed size. Among the catalyst loading conditions, pH level of precursor solution was changed by several solutions like Nitric acid or Sodium hydroxide. For the each case, it was heated at different drying temperatures that can affect the phase of catalyst loaded on support. From these results, it was studied that the effect of catalyst loading condition on the performance. 90wt% hydrogen peroxide was used as a monopropellant, and platinum was chosen as a catalyst. Characteristic velocity efficiency and temperature efficiency were used for the performance evaluation.