• Journal of electromagnetic engineering and science
• /
• v.9 no.1
• /
• pp.7-11
• /
• 2009

An Ultra-WideBand(UWB) Low-Noise Amplifier(LNA) is proposed and is implemented in a $0.18-{\mu}m$ CMOS technology. The proposed UWB LNA provides excellent wideband characteristics by combining a High-Pass Filter (HPF) with a conventional resistive-loaded LNA topology. In the proposed UWB LNA, the bell-shaped gain curve of the overall amplifier is much less dependent on the frequency response of the HPF embedded in the input stage. In addition, the adoption of fewer on-chip inductors in the input matching network permits a lower noise figure and a smaller chip area. Measurement results show a power gain of + 10 dB and an input return loss of more than - 9 dB over 2.7 to 6.2 GHz, a noise figure of 3.1 dB at 3.6 GHz and 7.8 dB at 6.2 GHz, an input PldB of - 12 dBm, and an IIP3 of - 0.2 dBm, while dissipating only 4.6 mA from a 1.8-V supply.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.12
• /
• pp.2300-2307
• /
• 2008

This study receives the noise transmitted in a constant audio frequency range through a microphone array in which the noise(like grease in a pan) occurs on the power supply line due to the troublesome partial discharge(arc). Then by going through a series of signal processing of removing noise, this study measures the distance and direction up to the noise caused by the troublesome partial discharge(arc) and monitors the result by displaying in the analog and digital method. After these, it determines the state of each size and judges the distance and direction of problematic part. When the signal sound transmitted by the signal source of bad insulator is received on each microphone, the signal comes only in the frequency range of 20 kHz by passing through the circuit of amplification and 6th low pass filter. Then, this signal is entered in a digital value of digital signal processing(TMS320F2812) through the 16-bit A/D conversion. By doing so, the sound distance, direction and coordinate of bad insulator can be detected by realizing the correlation method of detecting the arriving time difference occurring on each microphone and the algorithm of detecting maximum time difference.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.5
• /
• pp.245-249
• /
• 2006

Corona characteristics of conductors are dependent on the electric field conditions in the immediate vicinity of the conductors. In case of DC transmission line, particularly, the space charge plays an important role in the electric field distribution. Therefore, DC corona cage simulation is necessary for long-term test in the same conditions. This paper presents the results of designing and constructing hardwares such as DC power supply, measurement system and DAS to carry out the simulation. The corona cage longitudinally is divided into five equal length sections and three inner sections of those are isolated from the ground of outer cage. The measurement items are radio noise, corona current, television noise, audible noise and meteorological conditions. In the next step, various simulations about the type and configuration of two or three candidate conductors will be conducted. And then finally an environmentally-friendly conductor for HVDC overhead transmission line will be decided.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.2
• /
• pp.101-107
• /
• 2016

The main target in this paper is the localization of VME Type EPSM in Generator Exciter(EX2100) System. Developed EPSM has the compatibility with the existing product in the structure and shape and electrical feature and so on, but it has a much improved capacity and reliability in comparison with origin company product. this paper, to improve these functions, put emphasis on protection, monitoring, power capacity increase(over 120%), an enlarged scale of input voltage supply, AC/DC dual voltage use and so on. After manufacturing product localization, it was carried out several tests for the performance and reliability verification of developed product. These tests were performed in Authorized Inspection Agency(KTL) and field application test and maker self-test were additionally performed. Finally, the results of all tests were "success".

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.4
• /
• pp.405-411
• /
• 2020

In this paper, we designed the COS MEMS system for sensing the falling detection and explosive noise of fuse link in COS (Cut Out Switch) installing on the power distribution. This system analyzed the failure characteristics and an instantaneous breakdown of power distribution. Therefore, our system strengths the industrial competence and guaranties the stable power supply. In this paper, we applied BLE (Bluetooth Low Energy) technology which is suitable protocol for low data rate, low power consumption and low-cost sensor applications. We experimented with LSM6DSOX which is system-in-module featuring 3 axis digital accelerometer and gyroscope boosting in high-performance mode and enabling always-on low-power features for an optimal motion for the COS fuse holder. Also, we used the MP34DT05-A for gathering an ultra-compact, low power, omnidirectional, digital MEMS microphone built with a capacitive sensing element and an IC interface. The proposed COS MEMS system is developed based on nRF52 SoC (System on Chip), and contained a 3-axis digital accelerometer, a digital microphone, and a SD card. In this paper of experiment steps, we analyzed the performance of COS MEMS system with gathering the accelerometer raw data and the PDM (Pulse Data Modulation) data of MEMS microphone for broadcasting the failure of COS status.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1836-1840
• /
• 2003

This paper, we propose a new phase-locked loop (PLL) system with the controllable output phase, independent from the output frequency, and lock-up time. This PLL system has a dual control loop is described, the inner loop greatly improved VCO characteristic such as faster speed response as well as higher operation bandwidth, to minimize the effect of the VCO noise and the power supply variation and also get better linearity of VCO output. The main loop is the heart of this PLL which greatly improved the output frequency instability due to the external high frequency noise coupling to the input reference frequency also the main loop can control the output phase, independent from the output frequency, and reduce the lock-up time of the step frequency response. The experimental results confirm the validity of the proposed strategy.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.279-282
• /
• 2000

As digital systems continue to use components with faster edge rates and clock speeds, transmission of the digital information in these systems approaches the microwave realm. At these speeds digital signal fidelity becomes both a critical success factor and design challenge. The noise sources in digital systems include the noise in power supply, ground and packaging media due to simultaneous switching of drivers, signal reflections and distortions on single and multiple transmission lines. This paper presents theory, case studies and design considerations of gigabit interconnection for network and communication systems. The case studies show HSPICE and Ampredictor simulations of alternate approaches. Various subjects including skin effect and dielectric losses, interconnect simulations and crosstalks of connector, affected signal discontinuity, are addressed.

• Journal of the Korea society of information convergence
• /
• v.7 no.2
• /
• pp.7-12
• /
• 2014

Many filters are made in order to dectect the accurate signal. The performance of the filter is evaluated as to remove the noise effectively. It is necessary to determine the threshold value for the accurate evaluation of the filter effectively. In this study, we investigated the optimization of the threshold value. It was used for the triangular wave signal and the power supply noise. SNR change according to the number of samples was studied. As the number of samples increases, SNR saw also stabilizde.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2733-2735
• /
• 1999

The conducted noises mainly emitted from PWM DC power supply have a periodicity with respect to switching frequency, and especially center at the switching frequency and the discrete harmonic frequencies. The concentration of noise energy at these discrete frequencies makes it harder to meet EMI regulations. To reduce the conducted noises, this paper presents the novel FM-PWM control method by using random switching frequency modulation control. This control makes it to generate the noises of side bands by shattering emission spectrum, and to reduce the peak level of conducted noises.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.152-155
• /
• 2000

Oversampling modulators based on high-order sigma-delta modulation provide an effective means of achieving high-resolution A/D conversion in a VLSI technology. Because high-order noise shaping great]y reduces the quantization noise in the signal band. This paper introduces a third-order cascaded sigma-delta modulator that is stable for large input level. Modulator was simulated 3.3V single power supply voltage in 0.65$\mu\textrm{m}$ CMOS technology. It achieves 80㏈ SNR for a 20㎑ input signal bandwidth. A lock frequency is 3㎒ that is 80 oversampling ratio.