• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.6
• /
• pp.37-43
• /
• 1997

In this paper, an analog-domain powr-reduction technique for a low-voltage CMOS operational amplifier and its application to clock-based VLSI systems are proposed. The proposed technique cuts off the bias current of the op amp during a half cycle of the clock in the sleeping mode and resumes the curent supply sequentially during the remaining cycle of the clock in the normal operating mode. The proposed sequential sbiasing technique reduces about 50% of the op amp power and improves the circuit performance through high phase margin and stable settling behavior of the output voltage. The power-reduction technique is applied to a sample-and-hold amplifier which is one of the critical circuit blocks used in the front-end stage of analog and/or digital integrated systems. The SHA was simulated and analyzed in a 0.8.mu.m n-well double-poly double-metal CMOS technology.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.12
• /
• pp.20-27
• /
• 1997

In this paper, a multiplying digital-to-analog converter (MDAC) circuit for low-power high-resolution CMOS algorithmic A/D converters (ADC's) is proposed. The proposed MDAC is designed to operte properly at a supply at a supply voltge between 3 V and 5 V and employs an analog0domain power reduction technique based on a bias switching circuit so that the total power consumption can be optimized. As metal-to-metal capacitors are implemented as frequency compensation capacitors, opamps' performance can be varied by imperfect process control. The MDAC minimizes the effects by the circuit performance variations with on-chip tuning circuits. The proposed low-power MDAC is implementd as a sub-block of a 10-bit 200kHz algorithmic ADC using a 0.6 um single-poly double-metal n-well CMOS technology. With the power-reduction technique enabled, the power consumption of the experimental ADC is reduced from 11mW to 7mW at a 3.3V supply voltage and the power reduction ratio of 36% is achieved.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.507-515
• /
• 2004

With the advent of fast power devices, the high dv/dt voltage produced by PWM inverts have been found to cause EMI noise, shaft voltage and bearing current. This paper describes the application of newly developed Conducted EMI reduction SVPWM technique in induction motor drives. The newly developed common mode voltage reduction SVPWM technique don't use any zero-vector states for inverter control, hence it can restrict the common mode voltage more than conventional PWM technique. The validity of the proposed technique by software approach is verified through simulation and experimental results.

• ETRI Journal
• /
• v.44 no.3
• /
• pp.379-388
• /
• 2022

This study proposes a novel low-complexity algorithm for computing inverse fast Fourier transform (IFFT)/fast Fourier transform (FFT) operations in binary phase shift keying-modulated orthogonal frequency division multiplexing (OFDM) communication systems without requiring any twiddle factor multiplications. The peak-to-average power ratio (PAPR) reduction capacity of an efficient PAPR reduction technique, that is, H-SLM method, is evaluated using the proposed IFFT algorithm without any complex multiplications, and the impact of oversampling factor for the accurate calculation of PAPR is analyzed. The power spectral density of an OFDM signal generated using the proposed multiplierless IFFT algorithm is also examined. Moreover, the bit-error-rate performance of the H-SLM technique with the proposed IFFT/FFT algorithm is compared with the classical methods. Simulation results show that the proposed IFFT/FFT algorithm used in the H-SLM method requires no complex multiplications, thereby minimizing power consumption as well as the area of IFFT/FFT processors used in OFDM communication systems.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.7
• /
• pp.753-759
• /
• 2014

This paper introduces the reduction design technique of the resonance phenomenon of the inner PCB based on power integrity from the analysis about the inner power supply line generating RLC resonance. With the technique, the resonant frequency resulted from the structural characteristics of the PCB can be analyzed and allows to predict and the capacitor for resonance phenomenon reduction can be decided as a decoupling capacitor. From the simulation result, it was confirmed that the PCB's resonance phenomenon reduction design technique should have the reduction effect in the inner motherboard of the industrial controller. This research will be contributed to the improvement of the safety of a PDN (Power Delivery Network) structure in the layout design technique of the PCB.

• Journal of electromagnetic engineering and science
• /
• v.8 no.3
• /
• pp.119-128
• /
• 2008

In this paper, we propose a developing approach of 600 W super high frequency(SHF) traveling wave tube amplifier (TWTA) for communications. Also, we make a TWTA called the experimental-TWTA(ETWTA), which uses a cathode ripple reduction technique to improve RF performance. After implementation, we discuss, and compare it with some other TWTAs. Its RF performance is better than that of other TWTAs. Therefore, this methodology can be used to develop the high power SHF TWTA for communications.

• Journal of Magnetics
• /
• v.21 no.4
• /
• pp.593-598
• /
• 2016

In order to reduce the amount of noise component in X-ray imaging system, various reduction techniques were frequently used in the field of diagnostic imaging. Although the previous techniques -such as median, Wiener filters and Anscombe noise reduction technique - were able to reduce the noise, the edge information was still damaged. In order to cope with this problem, total variation (TV) noise reduction technique has been developed and researched. The purpose of this study was to evaluate and compare the image quality using normalized noise power spectrum (NNPS) and contrast-to-noise ratio (CNR) through simulations and experiments with respect to the above-mentioned noise reduction techniques. As a result, not only lowest NNPS value but also highest CNR values were acquired using a TV noise reduction technique. In conclusion, the results demonstrated that TV noise reduction technique is proved as the most practical method to ensure accurate denoising in X-ray imaging system.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.54 no.7
• /
• pp.458-461
• /
• 2005

Power dissipated during test application is substantially higher than power dissipated during functional operation which can decrease the reliability and lead to yield loss. This paper presents a new technique for power minimization during test application in full scan sequential circuits. This paper shows freezing of combinational logic parts during scan shift operation in test mode. The freezing technique leads to power to minimization. Significant power reduction in the scan techniques is achieved on ISCAS 89 benchmarks.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.531-534
• /
• 2005

This paper presents a new data line sharing technique for TFT-LCD panels. This technique reduces the number of data driver IC's to half by having two adjacent pixels share the same data line. This in turn doubles the number of gate lines, which are integrated directly on the glass substrate of amorphous silicon for further cost reduction and more compactness. The proposed technique with new pixel array structure was applied to 15.4 inch WXGA TFT-LCD panels and has proven that the number of driver IC's were halved with nearly 41% circuit cost reduction and 5.3% reduction in power consumption without degrading the image quality.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.321-324
• /
• 2005

This paper describes the application of newly developed conducted EMI reduction technique of SVPWM in induction motor drive. The newly developed common mode voltage reduction SVPWM technique doesn't any zero-voltage vector states for inverter control. Hence it can restrict the common mode voltage better than conventional PWM technique. The proposed technique is verified through simulation and experimental results. And by applying vector-controled system, the proposed technique have superior ability of reducing EMI and equal control performance comparing conventional SVPWM technique.