• 한국세라믹학회지
• /
• 제37권8호
• /
• pp.731-738
• /
• 2000

KLN(K3Li2Nb5O15) has attracted a great deal of attention for their potential usefulness in piezoelectric, electro-optic, nonlinear optic, and pyroelectirc devices. Especially, the KLN single crystal has been studied in the field of optics and electronics. However it is hard to produce good quality single crystals due to the crack propagation during crystal growing. One of the solutions of this problem is prepartion of thin film. But the intensive study has not been conducted so far. In this study, after the KLN thin film were prepared by R.F. magnetron Sputtering method on SiO2/Si substrate, the post-annealing methods of RTA(rapid thermal annealin) and IPA(insitu post annealing) were employed. The deposition condition of KLN thin film was RF power(100 W), Working pressure(100 mtorr). The commonness of both RAT and IPA was that the higher were deposition and post annealing temperature, the higher was the intensity of XRD but the less surface roughness. The difference of post-annealing methods affected XRD phase and surface condition very much. And in IPA process, the influence of O2 had much effect on the formation of KLN phase.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.46.1-46.1
• /
• 2010

Surface passivation of crystalline silicon(c-Si) surface with a-Si:H thin films has been investigated by using quasi-steady-state photo conductance(QSSPC) measurements. Analyzing the influence of a-Si:H film thickness, process gas ratio, deposition temperature and post annealing temperature on the passivation properties of c-Si, we optimized the passivation conditions at the substrate temperature of $200-250^{\circ}C$. Best surface passivation has been obtained by post-deposition annealing of a-Si:H film layer. Post annealing around the deposition temperature was sufficient to improve the surface passivation for silicon substrates. We obtained effective carrier lifetimes above 5.5 ms on average.

• 한국진공학회지
• /
• 제1권1호
• /
• pp.206-211
• /
• 1992

SIMOX SOI structures were formed by oxygen ion implantation with a dose of 2 1018 ions/cm2 at 180kev and post-implantation annealing at $1250^{\circ}C$ for 6 hours in nitrogen ambient. The oxygen redistribution process during post-implantation annealing was examined by AES and TEM. The electrical property of the structure was investigated by SRP method. We could find oxygen precipitates in SOI layer was discussed. And the limiting factor to the decrease of the precipitates during post-implantation annealing was discussed also.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(2)
• /
• pp.273-276
• /
• 2001

The origin of image-slicking in metal-insulator-metal type thin-film-diode(TFD) LCDs is the asymmetric current-voltage(I-V) characteristic of TFD element. we developed that MIM-LCDs have reduced-image-sticking and perfect symmetry characteristic. One-Time Post-Annealing (OPTA) heat treatment process was introduced to reduce the asymmetry and shift of the I-V characteristics, respectively. OPTA means that the whole layers of lower metal, insulator, and uuper metal are annealed at one time. The treatment temperatures and fabricated process of TFD element were under foot. Also, this low temperature fabricated process allows the application of plastic substrates.

• 열처리공학회지
• /
• 제18권4호
• /
• pp.223-228
• /
• 2005

Tube hydroforming provides a number of advantages over conventional stamping process, including fewer secondary operation, weight reduction, assembly simplification, adaptability to forming of complex structural components and improved structural strength and stiffness. It can produce wide range of products such as subframe, engine cradle, and exhaust manifold. In this study, the effect of the heat treatment conditions such as post seam annealing (PSA) and bright annealing (BA) on the ovality and hydro-formability of steel tubes has been investigated. Hydroformabilities have been estimated by the bulging heights obtained at various processing parameters such as internal pressure, axial feeding and heat treatment conditions. The ovality and forming height are strongly influenced by material properties after heat treatments.

• 전기전자학회논문지
• /
• 제23권2호
• /
• pp.704-709
• /
• 2019

본 논문에서는 다양한 열처리(annealing) 조건에서 tunneling field effect transistor(TFET)의 전기적 특성을 연구 하였다. TFET 샘플은 수소 혼합 가스(4 %) 및 중수소($D_2$) 혼합 가스 (4 %)를 사용하여 열처리를 진행하였으며 측정은 노이즈 차폐실에서 진행되었다. 실험 결과, 열처리 전과 비교하여 열처리 공정 후에 subthreshold slope(SS)이 33 mV / dec만큼 감소함을 확인할 수 있었다. 그리고 측정 온도 범위에서 온도가 증가할수록 $V_G=3V$ 조건에서 10 기압의 중수소 혼합 가스에 대해 평균 31.2 %의 노이즈가 개선됨을 확인할 수 있었다. $D_2$ 혼합 가스로 메탈 증착 후 열처리 공정(post metal annealing)을 실시한 결과, $I_D=100nA$ 조건에서 평균 30.7 %의 노이즈가 감소되었음을 확인할 수 있다.

• 한국전기전자재료학회논문지
• /
• 제33권2호
• /
• pp.93-98
• /
• 2020

We investigated the effect of a post-annealing process using ultraviolet (UV) light on the electrical properties of solution-processed InZnO (IZO) thin-film transistors (TFTs). UV light was irradiated on IZO TFTs for different time periods of 0s, 30s, and 90s. We measured transfer and retention stability curves to evaluate the performance of the fabricated TFTs. In addition, we measured height, amplitude, and phase AFM images to analyze changes in the surface and morphology of the devices. AFM measurements were performed by setting the drive amplitude of the cantilever tip to 47.9 mV in tapping mode, then dividing the device surface into 500 nm × 500 nm. In the case of IZO TFT irradiated with UV for 30s, the electron mobility and I_on/I_off ratio were improved, the threshold voltage was reduced by approximately 2 V, and the subthreshold swing also decreased form 1.34 V/dec to 1.11 V/dec.

• 한국세라믹학회지
• /
• 제33권3호
• /
• pp.299-306
• /
• 1996

We invesgated the fesibility of thin films deposition by pyrolysis of metalorganic precursors using chemical beam deposition (CBD) process. We attempted to understand the effects of deposition variables such as substrate temperature operating pressure effusion cell temperature and H2 partial pressure on the properties of MgF2 grown by CBD. Mg(tfac)2 was used as a precursor. MgF2 thin films were always grown in an amorphous state and crystallized bypost-annealing. he higher the substrate temperature and the lower the operating pressure the less the impurities I the deposited MgF2 thin films. H2 gas has to be supplied for the pyrolitic reaction of Mg(tfac)2 decomposition. MgF2 films annealed in H2 have lower C impurity than those annealed in O2. But their crysatllinity was independent of annealing atmosphere. The optimum conditions for the prepara-tion of MgF2 films by CBD process were as following : The substrate temperature 55$0^{\circ}C$ the operating pressure 10-4 torr; effusion cell temperature 21$0^{\circ}C$ the percentage of H2 100% Post-annealing in H2 gas was required to remove residual carbon and to form MgF2 crystalline phase.

• 한국분말재료학회지
• /
• 제27권1호
• /
• pp.1-7
• /
• 2020

In this research, a new medium-entropy alloy with an equiatomic composition of FeCuNi was designed using a phase diagram (CALPHAD) technique. The FeCuNi MEA was produced from pure iron, copper, and nickel powders through mechanical alloying. The alloy powders were consolidated via a high-pressure torsion process to obtain a rigid bulk specimen. Subsequently, annealing treatment at different conditions was conducted on the four turn HPT-processed specimen. The microstructural analysis indicates that an ultrafine-grained microstructure is achieved after post-HPT annealing, and microstructural evolutions at various stages of processing were consistent with the thermodynamic calculations. The results indicate that the post-HPT-annealed microstructure consists of a dual-phase structure with two FCC phases: one rich in Cu and the other rich in Fe and Ni. The kernel average misorientation value decreases with the increase in the annealing time and temperature, indicating the recovery of HPT-induced dislocations.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.290.2-290.2
• /
• 2016

Recently, organic thin-film transistors have been widely researched for organic light-emitting diode panels, memory devices, logic circuits for flexible display because of its virtue of mechanical flexibility, low fabrication cost, low process temperature, and large area production. In order to achieve high performance OTFTs, increase in accumulation carrier mobility is a critical factor. Post-fabrication thermal annealing process has been known as one of the methods to achieve this by improving the crystal quality of organic semiconductor materials In this paper, we researched the properties of pentacene films with X-Ray Diffraction (XRD) and Atomic Force Microscope (AFM) analyses as different annealing temperature in N2 ambient. Electrical characterization of the pentacene based thin film transistor was also conducted by transfer length method (TLM) with different annealing temperature in Al- and Ti-pentacene junctions to confirm the Fermi level pinning phenomenon. For Al- and Ti-pentacene junctions, is was found that as the surface quality of the pentacene films changed as annealing temperature increased, the hole-barrier height (h-BH) that were controlled by Fermi level pinning were effectively reduced.