• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.8
• /
• pp.1727-1734
• /
• 2011

In this paper, a position control scheme of the ink droplet is presented for the high image quality and print speed ink jet printer. The proposed scheme estimates the impact position and compensates it by control of the jet strobe time based on the dynamic equations describing the moving trajectory of the ejected ink droplet. Compared to the conventional jet strobe control which is based on the simple synchronization with the position signal of the ink jet nozzle, the proposed control scheme provides more accurate impact position control while the carrier is moving with accelerated or decelerated speed as well as steady state speed with fluctuations. The availability of printing during the acceleration and deceleration states of the carrier moving enables the print speed up and the frame size down which means the cost down.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.39 no.6
• /
• pp.587-598
• /
• 2021

This study aims to develop a multi-camera based MMS (Mobile Mapping System) technology for building a HD (High Definition) map for autonomous driving and for quick update. To replace expensive lidar sensors and reduce long processing times, we intend to develop a low-cost and efficient MMS by applying multiple cameras and real-time data pre-processing. To this end, multi-camera storage technology development, multi-camera time synchronization technology development, and MMS prototype development were performed. We developed a storage module for real-time JPG compression of high-speed images acquired from multiple cameras, and developed an event signal and GNSS (Global Navigation Satellite System) time server-based synchronization method to record the exposure time multiple images taken in real time. And based on the requirements of each sector, MMS was designed and prototypes were produced. Finally, to verify the performance of the manufactured multi-camera-based MMS, data were acquired from an actual 1,000 km road and quantitative evaluation was performed. As a result of the evaluation, the time synchronization performance was less than 1/1000 second, and the position accuracy of the point cloud obtained through SFM (Structure from Motion) image processing was around 5 cm. Through the evaluation results, it was found that the multi-camera based MMS technology developed in this study showed the performance that satisfies the criteria for building a HD map.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.2
• /
• pp.192-198
• /
• 2001

In this study, a methodology of synchronous control which can be applied to position synchronization of a two-axes driving system has been developed. The synchronous error is caused by model uncertainties and torque disturbance of each axis. To overcome these problems, the proposed synchronous control system has been composed of two speed controllers and one synchronous controller. The speed controllers based on PID control law are aimed at the following to speed reference. And the parameters of speed controllers have been designed in order that speed response of the second axis corresponds with one of first axis. Especially, considering to model uncertainties of each axis, the synchronous controller has been designed using H$\infty$ control theory. The controller eliminates the synchronous error by controlling speed of the second axis. The effectiveness of the proposed method has been verified through simulation.

• Journal of Positioning, Navigation, and Timing
• /
• v.2 no.1
• /
• pp.67-74
• /
• 2013

In this study, a remote controller was designed using localization technique. The designed remote controller system consists of infrared transmit/receive module for time synchronization, ultrasonic transmit/receive module for measuring the TOA value, and micro-controller for processing the measured data value. For the position estimation method of remote controller, the Savarese method was used which does not have a problem of diverging solution depending on initial value. The noise included in the measured value was removed by separating the signal and noise with the use of EMD method which is the non-stationary signal analysis technique. The designed system was tested by constructing a simulation environment, and the improvement of accuracy and precision for the application of EMD method was examined.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.5
• /
• pp.689-701
• /
• 2008

In this paper, a fully adaptive feedforward feedback synchronized tracking control approach is developed for precision tracking control of 6 degree of freedom (6DOF) Stewart Platform. The proposed controller is designed in decentralized form for implementation simplicity. Interconnections among different subsystems and gravity effect are eliminated by the feedforward control action. Feedback control action guarantees the stability of the system. The gains of the proposed controller can be updated on line without requiring any prior knowledge of Stewart Platform manipulator. Thus the control approach is claimed to be fully adaptive. By employing cross-coupling error technology, the proposed approach can guarantee both of position error and synchronization error converge to zero asymptotically. Because the actuators work in synchronous manner, the tracking performances are improved. The corresponding stability analysis is also presented in this paper. Finally, simulation is demonstrated to verify the effectiveness of the proposed approach.

• Journal of Embryo Transfer
• /
• v.7 no.2
• /
• pp.111-115
• /
• 1992

This experiment was carried out to study the behavior of the estrus cycle in sows shortened uterine horns and to see whether the embryos could be recovered nonsurgically. The uteri of sows(n=4) were surgically shortened. It took about 3 hours to surgically remove the middle section of both uterine horns. The lengths of the shortened uterine horns were 18.7 to 29.5cm. After treatment, two sows exhibited natural estrus and the intevals from surgery to estrus were 8 days and 15 days, respectively. But the sows were not successful on synchronization and superovulation with PMSG and PGF$_2$$\alpha$. In the resurgery for confirmative examination, the sows had 6 and 7 corpus lutelin in ovaries, respectively. One sow had a small adhesion between the infundibulum and ovary, and the other sow had unilateral uterine obstruction at the sutured position and purulent materials in the uterus.

• International Journal of Contents
• /
• v.12 no.3
• /
• pp.42-46
• /
• 2016

Kinetic typography is technology such as color, scale, position of the letter changes dynamically with time and it communicates information with aesthetics and originality. The purpose of this study is to identify the design factors in the formativeness of Hangul and present and implement the interaction design method of unique Hangul kinetic typography based on the scientific structure of Hangul. We implemented the Hangul kinetic typography system, which varies in sizes and motion directions according to a viewer's movement and exhibited in a media art event. To do this, we used a viewer's skeleton information on typography synchronization. The results indicated that Hangul kinetic typography has potential not only as a means to communicate with viewers but also as a medium to show the artistic value of Hangul.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1717-1722
• /
• 2003

In this paper we developed flip-chip bonder using XY stage, liner-rotary actuator and vision system. We depicted the major parts of the developed flip-chip bonder. Then we discussed several problems and their solutions such as vision and motion control, pick-up module position accuracy, separation of chip from the blue taped hoop, etc. We used a post guide to improve the horizontal positional accuracy against the long arm. Also, we used an ejector module and synchronization technique for easy chip separation from the blue tape.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.138-140
• /
• 2014

The image quality of the color laser printer is highly related with the motion quality of actuators. However, the high precision system requires high production costs in general. The proposed design method in this paper improves image quality without increasing production costs. Using the synchronization method, time gap between exposure and transfer in organic photo conductive (OPC) drum and the period of driving gear revolution are synchronized. The proposed method is verified by computer simulations and experiment, and showed by printed images.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2415-2417
• /
• 2002

In this paper, we discuss about the real-time distributed system for the control of to motors using uCOS-II kernel. Real-time kernel needs to process the tasks for two motors in desired time to synchronize motion. We used both semaphore and message mail box for synchronization. In the previous study, we used step motors for the actuator of two axes robot, but could not draw a clear line because of motor resolution and synchronizing step pulse. To resolve the problem we rebuilt the transfer robot with DC motors and the dedicated position servor which had built in out lab. Moreover we developed the PC based graphic user interface for generating planar drawing image control. Experimental results also presented to show the proposed control system is useful.