• Elastomers and Composites
• /
• v.29 no.3
• /
• pp.226-233
• /
• 1994

The properties of the mixed prepolymer-urethane in the range of 10-40 phr were observed. LBR and LCR have same functional group but different in structure of molecular. The viscosity of mixture depending on content of rubber, adhesive strength, thermal property and compatibility with a diluted solvent are as follows: 1. The viscosity of the mixture was influenced by solubility of the diluent for urethane resin and liquid rubber. 2. Adhesive strength showed the highest value at 30phr rubber, decreased gradually at above 30phr rubber. And LBR revealed better physical property than that of LCR. 3. The most effective factors affecting adhesive strength are molecular structure of rubber, the type of solvent, and volatility. 4. Urethane resin containing LBR showed better compatibility for solvent and faster drying velocity. 5. LBR showed more favorable compatibility and dispersion state than those of LCR by analyzing the results of SEM.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.47 no.3
• /
• pp.267-272
• /
• 2011

The behavior of abrasive wear on counterpart roughness of glass fiber reinforcement polyurethane resin (GF/PUR) composites were investigated at ambient temperature by pin-on-disc friction test. The friction coefficient, cumulative wear volume and surface roughness of these materials against SiC abrasive paper were determined experimentally. The major failure mechanisms were lapping layers, ploughing, delamination, deformation of resin and cracking by scanning electric microscopy (SEM) photograph of the tested surface. As increasing the counterpart roughness the GF/PUR composites indicated higher friction coefficient. The surface roughness of the GF/PUR composites was increased as the sliding velocity was higher and the counterpart roughness was rougher in wear test.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.293-295
• /
• 1987

This paper deals with the dielectric properties dielectric breakdown strength and mechanical tensile properties according to heat - treatment condition of polyurethane resin. This resin is heat - treated over a range of temperature from $50^{\circ}C$ to $150^{\circ}C$. It is shown that the dielectric dissipation factor decreases with increase of heat - treatment temperature of the sample exept for the sample heat - treated at $150^{\circ}C$. The maximum dielectric breakdown strength is appeared for the sample heat - treated for 10 hours at $100^{\circ}C$, after curing for 24 hours at room temperature. The optimal heat - treatment condition in the view point of the electrical and mechanical properties is appeared for the sample heat - treated for 10 hours at $100^{\circ}C$, after curing for 24 hours at room temperature.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.25-26
• /
• 2022

In this study, glued laminated timber were manufactured by different types of adhesives for larch and spruce. Adhesives used to manufacture glued laminated timber include resorcinol resin, phenol resorcinol resin, melamine resin, and polyurethane. The char thickness and char rate according to the type of adhesive forglued laminated timber were analyzed. Melamine, resorcinol, and polyurethane showed excellent fire resistance performance in that order.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.2
• /
• pp.356-363
• /
• 2012

In this study we synthesis Hybrid resin(WPC) by milk casein and waterborne polyurethane(WPU). Then we experiment how casein effect to Hybrid resins in Full-Grain leather coatings. According to measured data for solvent resistance, WPU resin and Hybrid resins had good property. As test of tensile strength, WPU had most low strength(2.130 $kg_f/mm^2$) and WPC-3(WPU 91: casein resin 9) had most high strength(2.191 $kg_f/mm^2$). Also we knew that most good property of abrasion is WPC-3(50.090 mg.loss). In elongation case, WPU had most good result(637 %) in this experiment.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.6
• /
• pp.1619-1626
• /
• 2020

In this study, the physical properties of water-dispersible polyurethane resins synthesized with polyammonium phosphate and HMDI were studied by coating film samples and full-grain surfaces. Solvent resistance was found to be unchanged in all samples, and in terms of tensile strength, DPU-AP3 (1.887 kgf/㎟) containing the most ammonium polyphosphate showed the lowest physical properties. The elongation rate was measured as 54 8% in the sample containing a large amount of ammonium polyphosphate. Abrasion resistance was measured as 548 mg.loss of a sample containing a lot of ammonium polyphosphate, and it was confirmed that the physical properties of the blended resin of ammonium polyphosphate and water-dispersible polyurethane were changed.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.92-99
• /
• 2016

Polyurethane resin used to leather coat was synthesized by the addition reaction of PPG and PTMG with different mole ratios. Physical characteristics of the synthesized polyurethane resin were measured by the SEM, FT-IR and the UTM. Increasing mole ratio of PTMG having four methylene groups caused the increase of abrasion resistance and tensile strength. The elongation was decreased. As we measured the solvent(toluene) resistance of poly urethane resin, it was found the there were no effect of PTMG mole ratios on the phyhsical properties of the resin. The viscosity was increased by ratio of PTMG mole ratio.

• Textile Coloration and Finishing
• /
• v.35 no.2
• /
• pp.98-106
• /
• 2023

The recent surge in night walkers and pedestrian traffic accidents has led to an increased interest in retro-reflection-based products, leading to several studies on retro-reflection. Nonetheless, achieving high durability and dispersibility of retro-reflective glass beads in viscous polyurethane coating resin remains challenging. To address this issue, this study conduct to functionalize the surface of glass beads for covalent conjugation to coating resin to enhance their dispersibility and durability in the coating resin. The study evaluated the dispersibility, chemical composition, and retro-reflection properties of the functionalized glass beads and coating resin. The results showed that the functionalized glass beads conjugated to the polyurethane coating resin and exhibited excellent dispersibility, high durability, and maintained retro-reflection efficiency.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.2
• /
• pp.296-304
• /
• 2014

For this research, prepared polyurethane dispersion of hard segment type and polyethylene emulsion wax. Use these resin, this article has been analyzed about mechanical properties variation by increasing amount of polyethylene emulsion wax on Lam skin leather and dried film. According to measure data for solvent resistance, PUD had good property. As known in the results, increase of polyethylene wax constant did not influence to big variation of hybrid resin properties. As test of tensile strength, PUD had good tensile characteristic($1.235kg_f/mm^2$) and PUD-EW4 had lowest tensile characteristic($1.022kg_f/mm^2$). As same as tensile characteristic, abrasion test determined PUD(52.225 mg.loss) had highest properties. In elongation case, PUD showed 698 % modulus which was best properties in this experiment.

• Corrosion Science and Technology
• /
• v.14 no.5
• /
• pp.207-212
• /
• 2015

The purpose of this research was to synthesize fluorine modified waterborne polyurethane dispersion (F-WPU) by soap-free (internal emulsifier) emulsion polymerization techniques, to prepare coating solution based on fluorine modified waterborne polyurethane dispersion (F-WPU) and to compare the chemical and thermo-mechanical properties on the electrogalvanized steel sheet. Environmentally friendly F-WPU was prepared with a fluorinated polyol containing 60 wt% of fluorine. There are various ways of combining a wide variety of fluorinated polyols and diisocyanate to exhibit novel properties of waterborne polyurethane dispersion. Components of coating solution were largely divided into 4 kinds i.e., F-WPU, acrylic emulsion, silane coupling agent, and colloidal silicate. F-WPU coating solution on the electro-galvanized steel sheet showed excellent properties of corrosion resistance, alkali resistance and heat resistance, as compared to other coating solutions using a general waterborne resin. The F-WPU coating solution's reliable effects are possibly due to the fluorine atoms incorporated even in a small amount of F-WPU.