• Proceedings of the KIEE Conference
• /
• 2008.09a
• /
• pp.229-230
• /
• 2008

The investigations included the measurements of volume currents and also internal space charges on epoxy samples of mm thicknesses. The current versus time relations were shown to correspond well with classical forms of dielectric response such as the Curie-von Schweidler model. After the time transient, near steady currents were extremely small and exhibited a significant temperature dependence, similar in relation to the Poole-Frenkel hoping transport model. Equivalent resistances were on the order of $10^{19}$ ohms and represent very weak charge transport. Electrically stimulated acoustic waves were used to quantify the small internal charges that would accumulate within the epoxy. There was a notable homocharge near both anode and cathode. The dielectric response and the internal charge were related to show a consistent model for charge transport within unfilled epoxy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1991.10a
• /
• pp.79-82
• /
• 1991

In this paper we examined, by using the PET film with thickness of 16-350$\mu\textrm{m}$, space charge focused on TSC peak at the slightly higher temperature than transition temperture of the glass. In the result we found that charge quantity, leaking current and absorbing current at TSC peak were rarely dependant its thickness at the Al foil contact electrde. In the case of Al evaporated electrode, the absorbing current was rarely dependent its thickness but TSC charge quantity at C-peak was increased directly proportional to its thickness and leaking current was decayed inversely proportional to its thickness. Also current-volteag characteristics showed sublinerar property under ohmic area at the Al evaporated electrode.

• Journal of Hydrogen and New Energy
• /
• v.8 no.1
• /
• pp.31-41
• /
• 1997

In order to investigate the mechanism of electrochemical hydrogenation reaction on Zr-based Laves phase hydrogen storage alloy electrodes, electrochemical charge/discharge characteristics, potentiostatic/dynamic polarizations and electrocehmical impedance spectroscopy(EIS) of Zr-Ti-Mn-Ni and Zr-Ti-Mn-Ni-M(M=Fe, Co, Al) alloys were examined. Electrochemical discharge capacities of the alloys were quite different with gas charge capacities. Therefore, it was considered that discharge capacities of the alloys depend on electrochemical kinetic factors rather then thermodynamic ones. Discharge efficiencies were increased linearly with exchange current densities. The results of potentiostatic/dynamic polarization measurements showed that electrochemical charge and discharge reaction of Zr-based Laves phase hydrogen storage alloys is controlled by charge transfer process at the electrode surface. The EIS measurements also confirmed this result.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.2311-2312
• /
• 2008

The investigations included the measurements of volume currents and also internal space charges on epoxy samples of mm thicknesses. The current versus time relations were shown to correspond well with classical forms of dielectric response such as the Curie-von Schweidler model. After the time transient, near steady currents were extremely small and exhibited a significant temperature dependence, similar in relation to the Poole-Frenkel hoping transport model. Equivalent resistances were on the order of 1019 ohms and represent very weak charge transport. Electrically stimulated acoustic waves were used to quantify the small internal charges that would accumulate within the epoxy. There was a notable homocharge near both anode and cathode. The dielectric response and the internal charge were related to show a consistent model for charge transport within unfilled epoxy.

• Journal of Electrochemical Science and Technology
• /
• v.4 no.2
• /
• pp.61-70
• /
• 2013

Corrosion inhibition of carbon steel in 2M HCl by some benzohydrazide derivatives (I-III) was studied using weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) techniques at $30^{\circ}C$. Polarization studies showed that all the investigated compounds are of mixed type inhibitors. Temperature studies revealed a decrease in efficiency with rise in temperature and corrosion activation energies increased in the presence of the hydrazide derivatives, probably implying that physical adsorption of cationic species may be responsible for the observed inhibition behavior. Electrochemical impedance studies showed that the presence of benzohydrazide derivatives decreases the double layer capacitance and increases the charge transfer resistance. The adsorption of these compounds on carbon steel surface was found to obey Temkin's adsorption isotherm. Synergistic effects increased the inhibition efficiency in the presence of halide additives namely KI and KBr. An inhibition mechanism was proposed in terms of strongly adsorption of inhibitor molecules on carbon steel surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.413-416
• /
• 1996

The ceramic dielectrics were fabricated by mixing of Mn $O_2$ and ZnO at (B $a_{0.85}$ $Ca_{0.15}$)Ti $O_3$ and studied for dielectric relaxation characteristics. The dielectric relaxation time was increased by space charge polarization of palaelectric layer at the low temperature and frequency but it was decreased by Interface polarization at the high temperature and frequency. The remnant polarization and coercive field of ceramic dielectrics was decreased by rising temperature.ure.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.70-77
• /
• 2000

In this paper, the effect of solution and age heat treatment to the corrosion behavior for the Ti-6Al-4V alloy were studied by cyclic polarization methods. Ti-6Al-4V was solution heat treated at $1,066^{\circ}C$ and $966^{\circ}C$ for 5 hours, and followed by age heat treated at $650^{\circ}C$, $600^{\circ}C$ and $550^{\circ}C$ with 1, 2, 4, 8 and 16 hours under vacuum environment. Test solution was 3.5% NaCl with temperature $25^{\circ}C$. The obtained results were as follows: 1. Base metal was exhibited higher electrical charge than that of solution and aged material. With decrease of solution-treatment temperature from 1066 to $966^{\circ}C$, the electrical charge was increased due to softening of micro structure. 2. The corrosion resistance of specimen that solution treated at $966^{\circ}C$ for 5 hours and age heat treated at 650, 660 and $550^{\circ}C$ were increased with increase of aging time to 4, 8 and 16 hours respectively, and then decreased. 3. In case of 316L stainless steel, measured charge and corrosion potential was 0.0627 coulomb and -614 mV respectively. Corrosion resistance of Ti-6Al-4V was higher than that of 316L.

• Proceedings of the KIEE Conference
• /
• 1985.07a
• /
• pp.204-206
• /
• 1985

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.349-352
• /
• 1987

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.12
• /
• pp.1108-1114
• /
• 1998

$BaTiO_3$ thin films preferred c-axis orientation for the potential application of ferroelectric memory devices were deposited on silicon substrates(100) by RF sputtering and annealed at 800 and 900[$^{\circ}C$] in air. The BT(100)/BT(110) peak ratio of the sputtered sample was decreased with post-annealing in air. According to increasing with annealing temperature and time, the peak ratio of BT(100)/BT(110) was decreased and the surface density of thin film was high. Dielectric characteristics of $BaTiO_3$ thin film was measured as a function of annealing temperature and frequency. The dielectric constants were increased with annealing and decreased with frequency by space charge polarization and dipole polarization below 600[kHz]. The remanent polarization and coercive field in P-E hysteresis loop of $BaTiO_3$thin film were increased with the annealing temperature in air. The remanent polarization and coercive filed annealed at 800[$^{\circ}C$] for 1hr were 1.2[$\mu$C/$cm^2$] and 200[kV/cm]