• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.2
• /
• pp.1-9
• /
• 1993

For frame synchronization in synchronous multiplexer based on SDH (Synchronous Digital Hierarchy), pointer justification mechanism (opinter adjustment) to compensate small frequency differences between the received uline clock and local clock is sed. But these pointer adjustment will introduce jitter onto tributary signal. This paper presents the bit leaking method to reduce those jitter to a level compatible with existing specification, where the simulation shows that this method reduces pointer adjustment jitter.

• The KIPS Transactions:PartC
• /
• v.10C no.4
• /
• pp.455-462
• /
• 2003

Techniques for the reduction of SRTS jitter and pointer adjustment jitter are studied. To reduce the stuffing jitter several methods have been proposed, such as bit leaking, stuff threshold modulation and sigma delta modulation. The characteristics of jitter generated in SRTS and pointer adjustment systen implementing these reduction techniques is analyzed with computer simulation. The results show that ms jitter value decreases to less than 50% as compared to a conventional pointer adjustment system. The amplitude of SRTS jitter using new techniques decreases or Increases dependent on system parameter.

• The Transactions of the Korea Information Processing Society
• /
• v.2 no.4
• /
• pp.561-566
• /
• 1995

In the degraded mode, there is frequency-misalignment between the node clocks in a synchronous network. Therefore the phase differences between node clocks fluctuate greatly. To keep the phase difference under allowable level the pointer adjustment technique is used Unfortunately these processes cause an inherent pointer adjustment jitter, that accumulates in a chain of pointer adjustment systems. To analyze the jitter, computer simulation is carried and the results is compared with experimental jitter values.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.7
• /
• pp.1196-1201
• /
• 2006

In pointer adjustment systems, 3 byte SDH clocks are controlled for synchronization. Therefore large jitter is generated in that systems. Bit stuffing technique was introduced as method for reducing pointer adjustment jitter. However, the jitter generated in this systems is also not so small. In this paper, the problems in the bit leaking system are analyzed and new bit stuffing technique is introduced to reduce the jitter sufficiently.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.6
• /
• pp.1091-1095
• /
• 2004

Bit leaking technique is analyzed as method for reducing pointer adjustment jitter. The method for jitter reduction is described, and simulation results are represented to illustrate rms jitter performance. The results show that rms jitter value decrease to less than 25% as compared to a conventional pointer adjustment system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.8
• /
• pp.1848-1853
• /
• 2003

Stuff threshold modulation(STM) technique is analyzed as method for reducing pointer adjustment jitter. The method for jitter reduction is described, and simulation results are presented to illustrate rms jitter performance. The results show that rms jitter value decrease to less than 50％ as compared to a conventional pointer adjustment system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.5
• /
• pp.533-540
• /
• 2013

Prime movers in engine rooms inherently are much affected by the adjustment of their governors for the steady state and transient properties, consequently requiring that marine engineers shall be well familiar with the way to manage governor dials for normal operation. The hydro-mechanical governors basically have different control characteristics and adjustment parameters of stability from digital governors. The former include compensation mechanism using dash pot while the control algorithm of the latter is usually based on the PID action. This study is for configuring a simulation module to let trainees practice how to adjust dials for stability on hydraulic governors in the view that the practice by real governors and engines is time consuming and high cost for operation. The governor module includes the adjusting points such as speed set, speed droop, needle valve and compensation pointer with engine module of $2^{nd}$ order coupled. The results of simulation showed satisfactory responses as a training tool for the adjustment of control parameters.